OPA656U
Product Specifications
OPA656U
Texas Instruments — Power Management & Signal Chain
Product Overview
The OPA656U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
OPA656U: 230 MHz JFET-input voltage-feedback operational amplifier in an 8-pin SOIC
OPA656U is a wideband voltage-feedback operational amplifier with a JFET input, 230 MHz of gain bandwidth and 130 volts per microsecond of slew in a SOIC body of 8 pins. The U suffix is the 8-pin SOIC body. The part provides 230 MHz of gain bandwidth product and 550 MHz of unity gain bandwidth with 130 volts per microsecond of slew, draws 11.7 milliamps typical and 16.7 milliamps maximum, and pairs a JFET input with a voltage-feedback topology, which is the combination that lets a wideband stage keep a picoamp class bias current.
Order code and package
| Order code | OPA656U |
| Function | wideband voltage-feedback operational amplifier with JFET input |
| Package | SOIC, 8 pins, body code D |
| Supply | plus or minus 5 V nominal, 10 V total |
| Supply current | 11.7 milliamps typical, 16.7 milliamps maximum |
| Gain bandwidth product | 230 MHz |
| Unity gain bandwidth | 550 MHz |
| Slew rate | 130 volts per microsecond on a 1 V step |
| Input | JFET, picoamp class bias current |
| Output | voltage-feedback output stage with the swing set by the supply |
| Stability | unity gain stable, with peaking specified at a gain of plus 1 |
| Datasheet | OPA656 wideband JFET family document |
Electrical parameters that decide the application
| Noise | low voltage noise JFET input, specified with a density curve rather than a single figure |
| Input capacitance | JFET gate capacitance, which sets the feedback pole with the transimpedance resistor |
| Output drive | capable of driving a back terminated cable at video rates |
| Peaking | specified at a gain of plus 1 with the recommended feedback resistor |
| Supply headroom | 10 V total, so a 5 V single supply is outside the specified range |
| Thermal | SOIC body, junction limit set by the package and the ambient |
| Operating range | industrial |
Points to check before this part goes on a BOM
230 MHz of gain bandwidth and 550 MHz of unity gain bandwidth are not the same measurement. The second is the frequency at which the open loop gain falls to one, and the first is the product of gain and bandwidth in the region where the response is single pole. At a gain of 10 the closed loop bandwidth is 23 MHz, and a board that assumes 550 MHz at a gain of 10 will be a factor of twenty out. Every wideband voltage-feedback part has this same pair of numbers and they are routinely swapped.
130 volts per microsecond at a 2 V peak to peak signal gives a full power bandwidth of about 10 MHz, so the slew rate and the gain bandwidth meet around a gain of 20. At a gain of 2 the part can deliver the full 23 MHz of small signal bandwidth with the signal held below 0.9 V peak to peak. Above that amplitude the output looks like a triangle wave and the distortion rises long before the bandwidth runs out.
11.7 milliamps typical and 16.7 milliamps maximum at 10 V total is 117 to 167 milliwatts, which in an SOIC body is a 20 to 30 degree rise before any load current. Driving a 100 ohm back terminated cable adds 25 milliamps at 2.5 V peak, which doubles the dissipation. This is a part that wants a copper pour under it, and the thermal resistance of the SOIC rather than the electrical rating is what limits a four channel board.
The JFET input is why a 230 MHz amplifier can be used as a transimpedance stage. Bias current in the picoamp class means a 1 megohm feedback resistor sees negligible DC error, and the noise gain of a transimpedance circuit is set by the source capacitance and the feedback resistor rather than by the amplifier. With 10 picofarads of photodiode capacitance and a 1 megohm resistor the feedback pole lands near 16 kHz and the circuit is stable with a small phase capacitor across the resistor.
The supply is 10 V total, so this is not a single supply part. On a plus or minus 5 V rail the output swing leaves about 1 V of headroom at each end and the input common mode is set by the JFET pair, which is typically plus or minus 3 V. A board that wants to run the part from 5 V and ground needs a different amplifier, and the 38 MHz rail-to-rail family covers that case at a fifth of the bandwidth.
Peaking at a gain of plus 1 is specified with the recommended feedback resistor, and the resistor is part of the specification. A board that fits 0 ohms in the feedback position, on the assumption that a unity gain buffer needs no resistor, sees a resonant peak in the response and often a sustained oscillation with a capacitive load. The published peaking number belongs to the published network, and deviating from it invalidates the stability claim rather than the bandwidth claim.
Where this order code fits
Wideband transimpedance amplifiers, CCD and photodiode front ends, high speed integrators, active filters and fast ADC drivers use this part. A voltage-feedback topology with a JFET input is the usual answer when a photodiode has to be amplified to a megahertz without the bias current of a bipolar input or the gain restrictions of a current-feedback stage. Boards comparing it with a neighbouring part start from our How to Choose an RF Amplifier page, and boards replacing a part that has gone end of life start from the Amplifier Cross Reference page.
Questions buyers ask
Is 550 MHz the bandwidth at a gain of 10? No. 550 MHz is unity gain bandwidth and the gain bandwidth product is 230 MHz, so a gain of 10 gives about 23 MHz. The slew rate then limits a large signal to about 10 MHz at 2 V peak to peak.
Can this part run from a single 5 V supply? No. The supply is 10 V total, plus or minus 5 V nominal, and the input and output ranges are specified against that. A 5 V single supply board needs a rail-to-rail part instead.
Why does a unity gain buffer need a feedback resistor here? Because the peaking specification is tied to the recommended resistor value. Substituting 0 ohms changes the loop and can produce a peak or an oscillation, especially into a capacitive load.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Medical Device Components page sets out the checks that keep a substitute from failing on the bench.