LM139ADR
Product Specifications
LM139ADR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM139ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM139ADR: quad differential comparator with open collector outputs in a 14-pin SOIC
LM139ADR is four independent voltage comparators with open collector outputs on one die in a SOIC body of 14 pins. The A suffix is the tighter offset grade of the LM139, and the part is specified over minus 55 to plus 125 C, which is the widest temperature range in the LM339 family. The four comparators share a supply from 2 to 36 V, work down to the negative rail on their inputs, and each output is an open collector transistor that can be tied to a logic rail above the supply.
Order code and package
| Order code | LM139ADR |
| Function | quad differential comparator |
| Package | SOIC, 14 pins, D body |
| Comparators | four, independent |
| Output | open collector, wired OR capable |
| Supply | 2 V to 36 V, or plus and minus 18 V split |
| Input common mode | includes the negative rail |
| Offset grade | A suffix, tighter than the plain LM139 |
| Temperature range | minus 55 to plus 125 C |
| Response time | about 1.3 microseconds typical at 5 V |
| Input bias current | low, in the nanoamp range for this family |
| Supply current | under 2 milliamps for the four comparators |
| Datasheet | SLCS006 revision Z, May 2025 |
Electrical parameters that decide the application
| Input stage | PNP differential pair, allows sensing at ground |
| Output sink | typically 16 milliamps, enough to drive an optocoupler or a small relay through a transistor |
| Output voltage | up to 36 V independent of the supply |
| Hysteresis | none internal, added with two resistors from the output |
| Offset | 2 millivolts maximum on the A grade over the full military temperature range |
| ESD | 2 kV HBM |
| Pin out | shared with the LM239 and LM339 and with the newer B versions |
| Response with overdrive | faster with a larger input overdrive, the 1.3 microsecond figure assumes 5 millivolts |
Points to check before this part goes on a BOM
The military temperature range is the reason this order code exists in a catalogue full of cheaper comparators. A board that has to hold its threshold from minus 55 to plus 125 C needs the part whose offset is specified across that range, not one whose numbers stop at 85 C and are assumed to hold beyond it.
The open collector output is what allows the four comparators to share one pull up resistor and produce a wired OR fault signal. That is a genuine saving in a monitor circuit, and it also means the output can swing to a rail above the comparator supply, which a push pull output cannot do.
Response time is quoted at a stated input overdrive. At 5 millivolts of overdrive the output changes in about 1.3 microseconds, and at 1 millivolt it takes several times longer. A protection circuit that assumes the fast number with a slow input ramp will let the fault through before the output moves.
The input stage works at the negative rail, so a current sense resistor on the low side can be monitored directly without a level shift. That single property removes an amplifier and its offset from the measurement path in most overcurrent detectors.
Where this order code fits
Overvoltage and window detectors, relay drivers and level translators in industrial and aerospace assemblies order this code because the four comparators can share one resistor network. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.
Questions buyers ask
Can the output pull up to a higher voltage than the supply? Yes, the open collector transistor is rated to 36 V independent of the comparator supply, which is how 3.3 V logic is driven from a 24 V monitor rail.
Is hysteresis built in? No. It is added externally with a resistor from the output to the input, and without it a slow moving input will produce multiple edges at the threshold.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.