Contact Us

ISO7221MDR

Brand: Texas Instruments
Texas Instruments ISO7221MDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7221MDR — Power Management & Signal Chain | Superb Automation

ISO7221MDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7221MDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7221MDR: the hundred and fifty megabit grade of the same dual isolator

ISO7221MDR is the M grade of the dual channel digital isolator in the eight pin SOIC on a large reel of 2500, the fastest of the four grades with 150 megabits per second and a propagation delay of 12 nanoseconds typical and 20 maximum. The input pulse width falls to 6.67 nanoseconds, and the input thresholds change to 0.7 times the supply rather than the fixed transistor transistor logic levels of the slower grades.

That threshold change is the practical difference. The A, B and C grades take a fixed 2 volt high level and 0.8 volt low level, while the M grade tracks the supply, so a 3.3 volt driver has to reach 2.3 volts and a 5 volt driver 3.5 volts. A board that moves from the C grade to the M grade has to check the driver swing as well as the timing.

ISO7221MDR as the vendor document publishes it

Channels2, one in each direction
Signaling rate1, 5, 25 or 150 megabits per second by grade
Propagation delay, A grade253 nanoseconds typical, 585 maximum
Propagation delay, B grade58 nanoseconds typical, 75 maximum
Propagation delay, C grade36 nanoseconds typical, 48 maximum
Propagation delay, M grade12 nanoseconds typical, 20 maximum
Common mode transient immunity25 kilovolts per microsecond minimum, 50 typical at 5 volts
Supply3 to 5.5 volts per side, 2.8 volts minimum on the C grade
Quiescent current8.5 milliamps typical, 17 maximum per side
Supply current at 1 megabit10 milliamps typical, 18 maximum
Withstand isolation2500 volts root mean square for 60 seconds
Maximum repetitive isolation560 volts peak
Maximum transient isolation4000 volts peak
Clearance and creepage4 millimetres
Distance through insulation8 micrometres
Temperature rangeminus 40 to plus 125 degrees
Package8 pins, SOIC body D
Catalogue codeISO7221MDR
Vendor statusactive
GradeM, 150 megabits per second
Carrierlarge reel of 2500
Input thresholds0.7 times the supply, not fixed logic levels

Four speed grades, four propagation delays

The family is published in four grades that differ only in speed. The A grade runs to 1 megabit per second with a propagation delay of 253 nanoseconds typical and 585 maximum. The B grade runs to 5 megabits with 58 nanoseconds typical and 75 maximum. The C grade runs to 25 megabits with 36 nanoseconds typical and 48 maximum. The M grade runs to 150 megabits with 12 nanoseconds typical and 20 maximum.

The input pulse width follows the grade: 1 microsecond on the A, 200 nanoseconds on the B, 40 on the C and 6.67 on the M. Paying for a faster grade than the bus needs buys nothing, and the slower grade is the one with the lowest current at a given data rate, because the output stage is not switching faster than the signal.

Two channels, one each way, in an eight pin body

ISO7221MDR is the dual channel member of the ISO722x family with the two channels in opposite directions: channel one passes from side one to side two, channel two passes back. The same-direction dual is a different part number, and the eight pin SOIC body is shared by both, so the direction is the only thing that decides which code goes on the order.

Each channel is a logic input and output buffer separated by a silicon dioxide barrier, with no integrated noise filter, which is why the propagation delay is short and the pulse width distortion is small. The part is specified over minus 40 to plus 125 degrees and runs from a 3 to 5.5 volt supply on each side.

Eight and a half milliamps quiescent, ten at a megabit

Each side of ISO7221MDR draws 8.5 milliamps typical and 17 milliamps maximum with no load, and the supply current on side one rises to 10 milliamps typical with a 1 megabit signal applied, because the output stage and the barrier are both switching. On side two the same signal takes 10 milliamps typical at 1 megabit on the opposite direction channel.

The common mode transient immunity is 25 kilovolts per microsecond minimum and 50 typical on a five volt supply, dropping to 15 and 40 on a mixed 5 volt and 3.3 volt arrangement, and to 10 and 30 when both sides run at 3.3 volts. That drop is the reason a barrier is specified at the supply it will actually run at rather than at the highest one in the table.

Twenty five hundred volts, four millimetres, and eight micrometres

The barrier of ISO7221MDR is rated 2500 volts root mean square of withstand for 60 seconds, 560 volts peak of maximum repetitive isolation voltage and 4000 volts peak of maximum transient isolation voltage. The external clearance and creepage are both 4 millimetres, the distance through the insulation is 8 micrometres, and the barrier capacitance is about 1 picofarad.

The 8 micrometre figure is the one that decides the life of the barrier rather than its type test, because the insulation thickness is what the time dependent breakdown depends on. Four millimetres of creepage is the number the board has to preserve, and a mounting pad or a test point placed across the gap reduces it without changing anything on the drawing.

The eight pin body, the reel, and the marking

ISO7221MDR is the eight pin SOIC body, published on a tube and on a large reel, with the R suffix marking the reel. The part is moisture level 1 at 260 degrees, so no bake is needed before reflow, and the lead finish is nickel palladium gold. The temperature range is minus 40 to plus 125 degrees on both carriers.

Level 1 is a real difference against the isolators in the wider bodies, several of which are level 2 or 3. A line that runs an eight pin isolator beside a sixteen pin one has two different floor life rules on the same board, and the handling instruction has to say which is which rather than applying the stricter rule to both and baking parts that do not need it.

Where a two channel isolator sits

ISO7221MDR belongs on an isolated universal asynchronous receiver transmitter, an isolated RS-485 or controller area network interface where the transceiver is already isolated on the bus side, a gate drive signal pair for a half bridge, and a serial peripheral interface link where only clock and data need to cross the barrier and the chip select stays local.

Two channels in opposite directions is the shape of a full duplex link, which is why this member of the family is the one used beside a transceiver: one channel carries the transmit data out and one carries the receive data back, and the direction control for a half duplex bus is generated on the isolated side rather than crossing the barrier.

What the grade letter decides besides speed

The four grades differ in more than the propagation delay. The A, B and C grades take fixed transistor transistor logic thresholds of 2 volts high and 0.8 volt low, while the M grade tracks the supply at 0.7 and 0.3 times the value. A driver that swings to 2.5 volts from a 3.3 volt rail works with the first three and not with the fourth.

The second difference is the input pulse width, which falls from 1 microsecond on the A grade to 6.67 nanoseconds on the M grade. A slow optocoupler replacement with a 100 microsecond pulse works with any grade, and a fast serial clock needs the narrow pulse width, so the grade follows from the signal rather than from the stock position.

The M grade changes the input thresholds as well as the speed, so the driver has to be checked. Our BOM scrubbing page covers the driver against the isolator, and the vendor consolidation page covers holding one grade on a line.

Can the M grade be dropped into a board built for the C grade? Electrically it can, provided the driver reaches 0.7 times the supply. A 3.3 volt logic output typically does, and a 2.5 volt output does not.

What is the supply current at 150 megabits? The current rises with the edge rate rather than with the data, so a continuously clocked link at 150 megabits draws more than the 10 milliamps quoted at 1 megabit, and the budget has to use the switching figure rather than the quiescent one.