Contact Us

AM26C31IPWR

Brand: Texas Instruments
Texas Instruments AM26C31IPWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AM26C31IPWR — Power Management & Signal Chain | Superb Automation

AM26C31IPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The AM26C31IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

AM26C31IPWR: quad RS-422 differential line driver in the 16-pin TSSOP

AM26C31IPWR is the four-channel driver that most 5 V balanced links still start from in a TSSOP body of 16 pins. The part is a quadruple differential driver with complementary outputs that meet TIA/EIA-422-B and ITU recommendation V.11. It runs from a single 5 V supply, draws 100 microamps typical quiescent current, switches in 7 ns typical with 0.5 ns of pulse skew, and puts its outputs into a high impedance state when the supply is removed.

Order code and package

Order codeAM26C31IPWR
Functionquad differential line driver, three-state outputs
StandardTIA/EIA-422-B and ITU recommendation V.11
EnableG active high and G bar active low, common to all four drivers
PackageTSSOP, 16 pins, 5.00 mm by 4.40 mm
Temperature gradeI, minus 40 to plus 85 C
Other gradesC 0 to 70 C, Q minus 40 to plus 125 C, M minus 55 to plus 125 C
Supplysingle 5 V rail
Quiescent current100 microamps typical
Outputs in power offhigh impedance, so an unpowered board does not load the bus
DatasheetSLLS103 revision P, December 1990 revised March 2024
Body optionsPDIP, SOIC, SO, SSOP, TSSOP, CDIP, CFP and LCCC

Electrical parameters that decide the application

Propagation delay7 ns typical on both edges
Pulse skew0.5 ns typical, which is what allows a clock pair to stay square at the far end
Quiescent current100 microamps typical with the outputs unloaded
Drive currentthe output stage sources and sinks the line current, so the supply current in service is far above the quiescent figure
Enable logicone enable input pair for all four drivers
Power offoutputs go high impedance, which removes the load an unpowered node would otherwise present
Common modethe driver output is differential, so the receiver at the far end sets the common mode window
Input levels5 V logic thresholds, so a 3.3 V host needs a level check on the enable and data pins
Package16-pin TSSOP in a 5.00 mm body
Thermalthe driver dissipation is the line current times the internal drop, split across four channels

Points to check before this part goes on a BOM

The 100 microamp figure is quiescent current with the outputs unloaded. A pair driving 100 ohms at 5 V moves 50 mA, so a link with four active pairs draws a couple of hundred milliamps from the 5 V rail and the feature list number describes the standby state, not the working one.

Seven nanoseconds typical and 0.5 ns of pulse skew are typical figures. The switching table carries the guaranteed numbers with the load and temperature conditions attached, and the difference between the two is what decides whether a 32 MHz pair closes timing at 85 C.

G and G bar are one enable for the whole package. A board that needs one pair tri-stated while another pair stays live cannot do it here, and the workaround of gating the data input leaves the line driven at whatever level the last state held.

The grade letter sits inside the order code. IPWR is the I grade, which stops at 85 C, while the same die is available as the Q grade to 125 C and the M grade to minus 55 C. A product qualified at 105 C ambient has to order the Q code or accept a temperature hole in the qualification.

Outputs go high impedance with the supply removed, so a board that is powered down on a shared bus does not drag the other nodes down. This is documented for this part and is not true of every driver in the same socket.

The 3.3 V relatives in the family quote 1.5 V typical differential output into 100 ohms, against the larger swing of this 5 V part. A cable that only just worked at 5 V can fail when the node moves to a 3.3 V driver, and the receiver threshold is where that shows up first.

The TSSOP body is 5.00 mm by 4.40 mm with 0.65 mm pitch. A SOIC footprint from an older build cannot take this code without an adapter, so a second source that only exists in SOIC is not a same-day swap.

Where this order code fits

Boards moving a legacy V.11 link to a smaller body usually start with the pin to pin cross reference before they change the driver supply. Boards comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Can one of the four drivers be disabled on its own? No. G and G bar control all four drivers together, so per-pair control needs a different part.

Is the IPWR code rated for 105 C ambient? No. It is the I grade, which stops at 85 C; the Q grade of the same die reaches 125 C.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.