ISO6720BDR
Product Specifications
ISO6720BDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO6720BDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO6720BDR: A Dual 50 Mbps Isolator With Both Channels Facing the Same Way
ISO6720BDR is a basic dual-channel digital isolator in a SOIC (D-8) body of 8 pins. It puts two 50 Mbps channels in an eight pin narrow body of 4.90 mm by 3.91 mm, both driving in the same direction, so a clock and a chip select can cross one barrier in one package.
Order code and package
| Ordering string | ISO6720BDR |
| Package | SOIC, 8 pins, D body, 4.90 mm by 3.91 mm nominal |
| Carrier | 3000 pieces on a large reel, level 2 260 C, one year floor life |
| Part marking | 6720B |
| Temperature range | Minus 40 to plus 125 degrees Celsius |
| Sibling rows | ISO6720BDR.A at the same 3000 pieces, ISO6720FBDR for the low default |
| Tube rows | None printed in this addendum, the family ships on reel only |
| Channel direction | Two channels, both from side 1 to side 2 |
| Default output | High, the FB suffix gives low |
Electrical parameters that decide the application
| Signaling rate | 50 Mbps |
| Isolation rating | 3000 VRMS per UL 1577 in the D body |
| Working voltage | 450 VRMS, 637 VPK repetitive peak |
| Transient and surge | 4242 VPK transient, 5000 VPK impulse, 6500 VPK surge |
| Common mode transient immunity | 150 kV per microsecond typical, 100 kV per microsecond minimum |
| Supply range | 1.71 to 1.89 V, or 2.25 to 5.5 V, per side |
| Level translation | 1.71 V to 5.5 V |
| Supply current per channel | 1.8 mA typical at 1 Mbps |
| Propagation delay | 11 ns typical, 18 ns maximum at a 5 V rail |
| Pulse width distortion | 0.2 ns typical, 7 ns maximum at a 5 V rail |
| External clearance | Above 4 mm |
| ESD across the barrier | Plus or minus 8 kV IEC 61000-4-2 contact discharge |
| Input threshold | CMOS with hysteresis |
| Enable pin | None in the eight pin body |
Family variants and how they differ
| ISO6720B | Both channels forward, default high, this part |
| ISO6720FB | Both channels forward, default low |
| ISO6721B | One channel each way, default high |
| ISO6721FB | One channel each way, default low |
| ISO6721RB | One channel each way with the pins arranged in the opposite order |
| ISO6721RFB | The reversed pin arrangement with the low default |
Points to check before this part goes on a BOM
The eight pin body carries no enable pin, so both channels run whenever both rails are above their lockout. A system that needs to park the bus during power up has to hold the far side in reset.
Both channels point the same way. A bidirectional line such as an I2C pair or a UART with flow control needs ISO6721B, which puts one channel in each direction.
The default state is the state the output takes when the input side is unpowered, not the state the input pin is sitting at. A gate drive that must not fire at power up is safer with the FB part.
3000 VRMS in the narrow body is a basic isolation rating. A reinforced barrier for mains-referenced circuitry is the ISO672x-Q1, which is named separately and is not the same part.
The 4 mm of external clearance in the narrow body is the physical limit that decides whether the part can be used at all in a mains-referenced application. A slot under the package does not increase the clearance through air, and the creepage along the surface has to be measured to the nearest pad.
Every row of this family ships on a 3000 piece reel with level 2 moisture classification, so a line that consumes a few hundred parts a year will be working from a broken reel. The parts remaining on a broken reel keep the same floor life, and the bag they were returned to is what protects them.
The pin count is the same for all six members, so a board can be assembled with either channel direction. That is also the reason a wrong line item is easy to miss: only the marking and the default state tell the parts apart once the reel label is gone.
Why two channels in one direction is a deliberate choice
An isolated converter often needs a switching clock to leave the controller side and a synchronisation or fault flag to come back. When the second line is unidirectional too, a dual forward part keeps the pin arrangement simple and avoids the extra channel count of a two-each-way device.
A dual isolator inside an isolated converter
When a converter has to send a switching clock across the barrier and read back a synchronisation flag, both lines travel in the same direction. Two forward channels in an eight pin body are enough, and the part is small enough to sit between the transformer and the controller without a second row of components.
The supply current matters less here than the delay. At 11 ns typical the barrier adds a rounding error to the clock edge, and a synchronisation loop that was tuned on a bench without the isolator will see slightly different timing once the part is fitted. Budgeting the 18 ns maximum rather than the typical figure keeps that surprise out of the first prototype.
The default state in a power sequence
Both rails do not always come up together. If the input side is powered first, the output side sits at its default and the receiving logic sees a fixed level until its own rail is valid. On a part with a high default that means a line that reads high through the whole window, which is correct for an active low enable and wrong for a start condition.
The eight pin body cannot be disabled, so the only lever is which default the part was ordered with. Reading that choice back from a bill of materials is easy when the F letter is present and hard when the description was copied from a distributor page that dropped it, which is why the marking on the body is worth recording at goods in.
Isolation class at the mains boundary
A basic barrier is the class that assumes the enclosure provides the second layer of protection, while a reinforced barrier is expected to stand alone. The 3000 VRMS rating in this narrow body is the basic class, and a product where the isolated side is accessible to a user needs the reinforced family instead. Reading the class before the part number saves a re-certification later.
The working voltage is the other half of the same argument. 450 VRMS of continuous working voltage is comfortable on a 24 V or 48 V system and nowhere near what a 230 V mains reference needs, so the part belongs on the control side of a product rather than across the mains boundary itself.
Where this order code fits
It is used where two fast digital lines cross one barrier and the board has room for an eight pin body rather than a sixteen pin wide body. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Does it work with 3.3 V on one side and 5 V on the other? Yes. Each side has its own supply and the part translates between 1.71 V and 5.5 V, so a 3.3 V controller and a 5 V gate driver can share the same barrier.
What happens when the input side loses power? The output goes to its default state, high for this part and low for the FB suffix, and stays there until the input side is powered again.
Is the eight pin body the same footprint as the older ISO7220? The pin arrangement follows the same general pattern as the earlier dual isolators, but the supply range and the 50 Mbps rate are the reasons to move, so the pin map has to be checked line by line.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.