Contact Us

INA333AIDGKR

Brand: Texas Instruments
Texas Instruments INA333AIDGKR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA333AIDGKR — Power Management & Signal Chain | Superb Automation

INA333AIDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA333AIDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA333AIDGKR: 25 microvolt zero drift instrumentation amplifier in a 8-pin VSSOP

INA333AIDGKR is a micro power zero drift instrumentation amplifier for low level sensors in a VSSOP body of 8 pins. The INA333 is the tighter of the two micro power instrumentation amplifiers in this line: 25 microvolts of offset, 0.1 microvolts per C of drift and 50 microamps of supply current, at gains of 100 and above. One resistor sets the gain from 1 to 1000 with the same 1 plus 100 kiloohm over RG relation, and the VSSOP body is one of two package options.

Order code and package

Order codeINA333AIDGKR
Functionzero drift instrumentation amplifier
Gain1 to 1000, set by one external resistor
Gain equationG equals 1 plus 100 kiloohms divided by RG
PackageVSSOP, 8 pins
Package optionsVSSOP 8 and WSON 8 on the same die
Supply1.8 V to 5.5 V single rail
Input range0.1 V inside each rail
Quiescent current50 microamps
Temperature rangeminus 40 to plus 125 C
Inputradio frequency filtered
DatasheetSBOS513 revision C

Electrical parameters that decide the application

Offset voltage25 microvolts maximum at gains of 100 and above
Offset drift0.1 microvolts per C at gains of 100 and above
Noise50 nanovolts per root hertz at gains of 100 and above
Common mode rejection100 dB minimum at gains of 10 and above
Input bias current200 picoamps maximum
Supply current50 microamps typical
Output range0.05 V inside each rail
Zero driftinternal correction at a fixed rate, which sets a noise floor in the audio band
Gain errorexternal resistor tolerance dominates
Shutdownnot provided on this part

Points to check before this part goes on a BOM

The 25 microvolt offset figure is a maximum at gains of 100 and above. At lower gains the input referred offset increases, so a board that uses gain 10 and quotes the front page number is quoting a condition it is not running at.

Zero drift correction inside the part runs at a fixed rate, and that rate shows up as a small tone in the output spectrum. Low frequency measurements never see it, and an audio band application has to filter it.

Fifty microamps is the supply current of the amplifier alone. The bridge, the reference and the converter behind it usually draw more, so the amplifier is rarely the part that decides the battery life even though it is the one quoted in the power budget.

The gain resistor is the accuracy limit. A 0.1 percent resistor gives a 0.1 percent gain error on a die trimmed to the equation, and a trim in production that ignores the resistor tolerance gains nothing.

Input bias current of 200 picoamps keeps a high impedance bridge usable. A 10 kiloohm source with a 200 picoamp bias is 2 microvolts of offset error, which is small beside the 25 microvolt budget but not beside a 10 microvolt signal.

There is no shutdown pin. A battery product that powers the amplifier down between readings needs a load switch or a part from the family that provides one, because this body has no enable.

Where this order code fits

Handheld instruments, pressure bridges and portable medical front ends are the boards that use it, where the sensor signal is tens of microvolts and the battery has to last. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Why is the offset quoted at gains of 100 and above? Because the input referred offset of the stage grows as the gain falls; the trimmed figure applies at the high gains a low level sensor normally uses.

Can it drive a 12 bit converter directly? It can, within 50 millivolts of each rail, and the noise at gains of 100 and above is low enough that a 12 bit converter is limited by its own reference rather than by the amplifier.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.