Contact Us

INA163UA

Brand: Texas Instruments
Texas Instruments INA163UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA163UA — Power Management & Signal Chain | Superb Automation

INA163UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA163UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA163UA: a one nanovolt audio instrumentation amplifier in a tube

INA163UA is a current feedback instrumentation amplifier built for low level audio and instrumentation: 1 nanovolt per root hertz at 1 kHz, 0.002 per cent of distortion at a gain of 100, a gain set by one resistor from 1 to 10000, 800 kHz of bandwidth at a gain of 100 and 10 milliamps of supply current. The tube holds fifty pieces of the fourteen pin SOIC, which is a prototype and first article quantity.

The part is a specialist and the page treats it as one. Its bias current of 2 microamps typical and 12 maximum is the price of the nanovolt input stage, so it belongs on a 200 ohm source such as a moving coil cartridge or a microphone and not on a 10 kohm bridge. Its supply is plus or minus 4.5 to plus or minus 18 volts, so it does not run from a single 5 volt rail at all.

INA163UA as the vendor document publishes it

Gain range1 to 10000 V/V
Gain law1 plus 6 kohm divided by RG
Gain error, G = 10.1 per cent typical, 0.25 maximum
Gain error, G = 1000.2 per cent maximum
Gain drift, G = 11 ppm per degree typical, 10 maximum
Gain drift, G above 1025 ppm per degree typical, 100 maximum
Nonlinearity, G = 10.0003 per cent of full scale
Offset50 plus 2000 over G microvolts typical, 250 plus 5000 over G maximum
Offset drift1 plus 20 over G microvolts per degree
Supply rejection1 plus 50 over G microvolts per volt typical
Common mode rejection, G = 170 dB minimum, 80 typical
Common mode rejection, G = 100100 dB minimum, 116 typical
Input bias current2 microamps typical, 12 maximum
Input impedance60 megohms in parallel with 2 picofarads
Voltage noise at 1 kHz1 nanovolt per root hertz
Distortion at 1 kHz, G = 1000.002 per cent total harmonic plus noise
Bandwidth, G = 13.4 MHz
Bandwidth, G = 100800 kHz
Slew rate15 volts per microsecond
Settling to 0.01 per cent, G = 1003.5 microseconds on a 10 V step
Output swingwithin 2 volts of each rail into 2 kohm
Quiescent current10 milliamps typical, 12 maximum
Supply rangeplus or minus 4.5 to plus or minus 18 volts
Bodyfourteen pin SOIC, marking INA163UA
Temperature rangeminus 40 to plus 85 degrees specified
Catalogue codeINA163UA
Vendor stringINA163UA
Carrierfifty piece tube, SO-14
Moisture levellevel 3, 260 degrees, 168 hour floor life

One nanovolt per root hertz and 0.002 per cent of distortion

INA163UA is a current feedback instrumentation amplifier built for one job: amplifying a very small signal without adding noise or distortion. Voltage noise is 1 nanovolt per root hertz at 1 kHz, 1.2 at 100 Hz and 2 at 10 Hz referred to the input, current noise is 0.8 picoamps per root hertz, and the output stage contributes 60 nanovolts per root hertz. Total harmonic distortion plus noise is 0.002 per cent at 1 kHz and a gain of 100.

Against a 200 ohm source, which is what a moving coil cartridge or a low impedance microphone presents, the voltage noise and the thermal noise of the source are within a factor of two of each other, and the vendor says so: the part delivers near theoretical noise performance for that source. On a 10 kohm source the source noise dominates and the 1 nanovolt is wasted. That is why the family lists microphone preamps and moving coil transducers first and why the bias current, not the noise, is what limits it on a high impedance sensor.

Two microamps of bias current is the price of the noise

Bias current on INA163UA is 2 microamps typical and 12 maximum, with 10 nanoamps per degree of drift, an offset current of 0.1 microamps typical and 1 maximum, and an input impedance of 60 megohms in parallel with 2 picofarads. Those are bipolar input numbers and they are the direct consequence of a 1 nanovolt input stage: a low voltage noise bipolar pair carries a high base current, and no amount of trimming removes it.

The arithmetic is unforgiving on a high impedance source. Twelve microamps into 1 kohm is 12 millivolts of error, two thousand times the maximum offset at the same gain, and into 10 kohm it is 120 millivolts, which saturates the output at any useful gain. On a 200 ohm source, which is the case the part was built for, the same current is 2.4 millivolts. That is why the family's application list starts with microphones and moving coil transducers and mentions bridges second: a 350 ohm bridge is inside the window, a 10 kohm one is not.

A gain of 1 to 10000 from one resistor

Gain on INA163UA is set by a single external resistor and the law is 1 plus 6 kohm divided by RG, so a 6 kohm resistor gives 2, a 600 ohm gives 11, a 60 ohm gives 101 and a 6 ohm gives 1001. The range is quoted as 1 to 10000 V/V and the vendor's gain accuracy note is explicit that the number depends on the external resistor: the internal network is trimmed to 0.1 per cent at a gain of 1, but the resistor's tolerance, its drift and its parasitic inductance all enter at every other gain.

What the current feedback topology changes is the bandwidth. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain; this one holds 800 kHz at a gain of 100 and 3.4 MHz at unity, a ratio of four for a gain ratio of a hundred, and the vendor's gain against frequency curves show the same shallow slope at every step. That is what makes a gain of 1000 at audio frequencies practical, and it is also why the part does not need a compensation capacitor at any gain.

Offset written as a function of gain

The offset row on INA163UA is written as 50 plus 2000 divided by G microvolts typical and 250 plus 5000 divided by G maximum, which at a gain of 1 is 2.05 and 5.25 millivolts, at a gain of 100 is 70 and 300 microvolts, and at a gain of 1000 is 52 and 255 microvolts. Drift follows the same shape, 1 plus 20 over G microvolts per degree typical. The reason is that the input stage's offset is referred to the input while the output stage's offset is divided by the gain, so the first term dominates at high gain and the second at low gain.

Reading the row correctly changes what a gain of 1 channel can be used for. At unity the part has 5.25 millivolts of maximum offset and a drift of 21 microvolts per degree, which is a monitoring grade front end and not a precision one, however good the noise is. At a gain of 100 the same part has 300 microvolts of offset and 1.2 microvolts per degree, which is a measurement grade channel. The part is not better at high gain by accident; the topology refers the output stage error back through the gain.

Eight hundred kilohertz at a gain of 100

Slew rate on INA163UA is 15 volts per microsecond, settling to 0.1 per cent on a 10 volt step at a gain of 100 is 2 microseconds and to 0.01 per cent 3.5 microseconds, overload recovery from a 50 per cent overdrive is 1 microsecond, and the output is stable into 1000 picofarads. The 800 kHz at a gain of 100 is the row that matters for audio: it keeps the closed loop flat to well past 20 kHz at a gain that a microphone preamp actually uses, and it keeps the distortion mechanism, which is a slew rate effect at high frequency, out of the audio band.

The output swing is within 2 volts of each rail minimum and 1.8 typical into a 2 kohm load, so on plus or minus 15 volts the usable output is about plus or minus 13 volts, which is 26 volts peak to peak or 9.2 volts RMS. For a professional audio chain running plus or minus 15 volt rails that is the standard headroom, and the part's 60 milliamp short circuit current is what allows it to drive a 600 ohm load without an external buffer.

Plus or minus 4.5 to 18 volts and the fourteen pin body

INA163UA runs from a supply between plus or minus 4.5 and plus or minus 18 volts, rated at plus or minus 15, and draws 10 milliamps typical and 12 maximum quiescent. That is a high current for a front end amplifier and it is what the 1 nanovolt input stage and the 800 kHz bandwidth at a gain of 100 cost. The body is the fourteen pin SOIC, specified from minus 40 to plus 85 degrees with operation to plus 125, at 100 degrees per watt junction to ambient, so 12 milliamps at 30 volts total is 360 milliwatts and a 36 degree rise.

The single body and the single grade are worth knowing before a second source is discussed. The catalogue carries INA163UA in a tube and on a 2500 piece reel, both with the marking INA163UA and a moisture level of 3 with a 168 hour floor life. There is no automotive row and no dual member of the family, so a channel that needs two of these needs two packages, and a board that has to fit a smaller body is looking at a different family rather than at a variant of this one.

Fifty pieces is two prototype builds, which is the right quantity for a part that has to be characterised in the actual microphone circuit. Our amplifier cross reference page covers the quieter or lower current members of the family, and the lead time page covers the long quote case on a specialist part.

What resistor sets a gain of 100? Six kohm divided by the gain minus one, so 60.6 ohm gives 100. Use a 0.1 per cent part with a low temperature coefficient, because the gain accuracy is only as good as that resistor.

Can it run from a single 5 volt supply? No. The window starts at plus or minus 4.5 volts and the output needs 2 volts of headroom on each side.