INA155UA-2K5
Product Specifications
INA155UA-2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA155UA-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA155UA-2K5: the hyphen spelling of the 2500 piece reel
INA155UA-2K5 is the reel code with a hyphen inserted before the quantity. The vendor addendum prints INA155UA/2K5, the catalogue prints the hyphen, and the two strings resolve to the same body: the eight pin SOIC, the UA grade, 2500 pieces on a reel. The page exists because the strings are searched and quoted separately and a buyer comparing two quotes sees two line items that look like two parts.
What is not the same between two quotes is the packing detail. The addendum prints the reel quantity and the moisture level per row, and a quote that omits them is a quote that will be corrected at packing. On this family the reel is the only carrier besides rails, so the item that has to be confirmed is the moisture level on the bag rather than the body, which never changes.
INA155UA-2K5 as the vendor document publishes it
| Gain | 10 V/V with pin 1 open, 50 V/V with pin 1 linked |
| Gain law with an external resistor | 10 plus 400 kohm divided by 10 kohm plus RG |
| Gain error, G = 10 | 0.02 per cent typical, 0.1 maximum |
| Gain error, G = 50 | 0.05 per cent typical, 0.25 maximum |
| Gain drift, G = 10 | 2 ppm per degree typical, 10 maximum |
| Offset | 200 microvolts typical, 1 millivolt maximum |
| Offset over temperature | 1.5 millivolts maximum |
| Offset drift | 5 microvolts per degree |
| Common mode rejection, G = 10 | 80 dB minimum, 100 typical on the UA grade |
| Common mode rejection, G = 50 | 77 dB minimum, 90 typical on the UA grade |
| Input bias current | 1 picoamp typical, 10 picoamps maximum |
| Input impedance | 10 to the 13 ohms in parallel with 3 picofarads |
| Voltage noise at 1 kHz | 40 nanovolts per root hertz |
| Bandwidth, G = 10 | 550 kHz |
| Bandwidth, G = 50 | 110 kHz |
| Slew rate | 6.5 volts per microsecond |
| Settling to 0.01 per cent | 8 microseconds at G = 10, 15 at G = 50 |
| Output swing from rail | 5 millivolts typical, 10 maximum into 10 kohm |
| Quiescent current | 1.7 milliamps typical, 2.1 maximum, 2.6 over temperature |
| Supply range | 2.7 to 5.5 volts specified, 2.5 to 6 volts operating |
| Body | eight pin SOIC in the UA grade |
| Temperature range | minus 40 to plus 85 degrees specified |
| Catalogue code | INA155UA-2K5 |
| Vendor string | INA155UA/2K5, hyphen is a catalogue rendering |
| Carrier | 2500 piece reel |
| Grade | UA, 80 dB minimum rejection at a gain of 10 |
Rail to rail output, five millivolts from the rail on 2.7 volts
The output of INA155UA-2K5 reaches to within 5 millivolts of either rail typical and 10 millivolts maximum into a 10 kohm load, which is what makes a single 3.3 volt rail usable for a sensor that spans most of the supply. The input is a different story: the common mode window runs from 0.3 to 5.2 volts on a 5.5 volt supply and from 0.2 to 2.5 volts on 2.7 volts, so the input does not reach either rail and the last 0.3 volts at the top are outside the window.
That asymmetry sets the reference. On a single supply the Ref pin sits at mid rail, the output swings both ways around it, and the usable span is 5 millivolts to supply minus 5 millivolts. A 12 bit converter behind it then sees the full code range, which is the reason the part is sold as an analogue front end rather than as a general purpose amplifier: the two errors that usually eat the top and bottom of a converter's range are the ones the rail to rail output removes.
Where a fixed gain CMOS front end is the right buy
INA155UA-2K5 earns its place in four kinds of channel: a bridge, RTD or thermocouple front end where the source impedance is high and the bias current has to be picoamps; a battery instrument where the rail to rail output lets a 3.3 volt converter use its whole range; a medical amplifier where the input is a pair of electrodes and the offset has to be small enough not to saturate the second stage; and a multiplexed logger where 5 microseconds of settling buys channels.
It stops at four things. The gain is 10 or 50 and the resistor between them costs the trimmed accuracy. Common mode rejection falls from 100 dB at a gain of 10 to 90 at 50, so a channel that needs rejection at high gain is looking at the three op amp parts with a higher supply. The supply ceiling of 5.5 volts rules out a plus or minus 15 volt front end entirely. And the 5.5 MHz gain bandwidth caps a full scale signal at a few hundred kilohertz whatever the small signal curve suggests.
Two hundred microvolts of offset and one picoamp of bias
Offset on INA155UA-2K5 is 200 microvolts typical and 1 millivolt maximum referred to the input, 1.5 millivolts over the full temperature range, with a drift of 5 microvolts per degree. Bias current is 1 picoamp typical and 10 picoamps maximum on each input, offset current the same, and the input impedance is 10 to the 13 ohms in parallel with 3 picofarads. On a bridge or a thermocouple that combination is close to ideal, because the source impedance never generates an error the amplifier cannot ignore.
The picoamp figure only holds inside the common mode window and inside the diode clamp. The inputs are clamped to the rails, and the vendor states that a signal swinging more than 0.5 volts beyond either rail has to be current limited to 10 milliamps or less, which means a series resistor on any input that can see a cable fault. Ten picoamps into 1 gigohm is 10 millivolts, ten times the maximum offset, so a high impedance source needs a guard ring and a clean board rather than a better grade of the same part.
A gain of 10 or 50 from a strap on pin 1
INA155UA-2K5 is a three amplifier CMOS instrumentation amplifier with the feedback resistors trimmed on the die to a gain of 10 V/V, and pin 1 decides whether an extra pair is brought in to make that 50. Gains between the two are set with one resistor in series with the RG pins, and the vendor gives the law as 10 plus 400 kohm divided by 10 kohm plus RG, so 400 kohm of external resistance lands near 20 and 100 kohm lands on 50 exactly.
The strap is the part that gets taken for granted. The 0.02 per cent gain error printed in the table belongs to the internal network alone, so a 1 per cent resistor in the strap turns the channel into a 1 per cent channel, and a mechanical jumper with a tired contact adds a resistance the vendor never characterised. Use a solder link or a zero ohm part, and keep the trace from the strap pin short, because that node sits at the summing point of the first stage.
1.7 milliamps, a 2.7 volt floor and two bodies
INA155UA-2K5 draws 1.7 milliamps typical and 2.1 maximum, rising to 2.6 over temperature, from a supply specified between 2.7 and 5.5 volts and operating between 2.5 and 6. At 5.5 volts and 2.1 milliamps the dissipation is 11.6 milliwatts, which in the eight pin body at 150 degrees per watt raises the junction 1.7 degrees, so the package is never the limit at any point in the window. Short circuit current is 50 milliamps into ground and the output is stable into the capacitive load shown in the vendor curve.
Two bodies carry the part. The SO-8 holds the U and UA grades on rails or on a 2500 piece reel, and the MSOP-8 holds the E and EA grades on a 250 or a 2500 piece reel with the marking A55. Both are specified from minus 40 to plus 85 degrees for the electrical table and from minus 55 to plus 125 for operation, which is a wide operating window with a narrow guarantee and is the row to check when a channel has to survive a cold start rather than to measure accurately at minus 40.
550 kHz at a gain of 10, 110 at 50
INA155UA-2K5 carries 550 kHz of small signal bandwidth at a gain of 10 and 110 kHz at 50, which is the same 5.5 MHz gain bandwidth product written twice. Slew rate is 6.5 volts per microsecond, settling to 0.1 per cent is 5 microseconds at a gain of 10 and 11 at 50, and to 0.01 per cent it is 8 and 15. Overload recovery from a 50 per cent overdrive is 0.2 microseconds, which is fast because the amplifier never leaves its linear region far enough to saturate an internal node.
Those numbers fit a multiplexed front end comfortably. Sixteen channels at 11 microseconds of settling is 176 microseconds per scan, so a 10 kilo-sample logger can scan sixteen channels five times over in its period, and the amplifier is not the limit. What limits the scan is the input filter and the multiplexer charge injection, both of which have to settle through the same 5 microsecond window, and the vendor's own application note on driving converters puts the series resistor and the capacitor around that arithmetic.
Compare the moisture level and the reel diameter rather than the unit price alone, because two quotes for the same 2500 pieces can differ in both. Our traceability report page covers what has to travel with the reel, and the lead time page covers the long quote case.
Is the hyphen part of the orderable string? No. The vendor prints the slash, and a distributor system that requires the hyphen is applying its own convention. Put the slash free string on the purchase order and the vendor part number in the description.
Does the reel size change the electrical behaviour? No. It changes the packing, the feeder and the floor life record.