INA145UA
Product Specifications
INA145UA
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA145UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA145UA: gain of 1 to 1000 from two external resistors
INA145UA is a programmable gain difference amplifier with a 40 kohm input network and a 10 kohm output resistor, and the gain is set outside the package as 1 plus the ratio of two resistors. That is what separates it from the fixed gain members of this family: one part number covers a strain bridge at 100, a shunt at 10 and a line receiver at 1, and the gain accuracy follows the resistors that are fitted.
The UA suffix is the only grade the vendor publishes for this family, so there is no tighter bin to step up to. What there is instead is a decision about the external pair: a 0.1 per cent network with 25 ppm tracking costs more than the amplifier and sets the gain error, while a 1 per cent pair costs almost nothing and limits the channel to roughly 8 bits of gain accuracy.
INA145UA as the vendor document publishes it
| Gain | 1 V/V to 1000 V/V, set by two external resistors |
| Gain equation | 1 plus the ratio of RG2 to RG1 |
| Gain error at unity | 0.01 per cent typical, 0.1 maximum |
| Gain drift | 2 ppm per degree typical, 10 maximum |
| Nonlinearity | 0.0002 per cent typical, 0.005 maximum of full scale |
| Offset | 200 microvolts typical, 1 millivolt maximum |
| Offset drift | published as a typical curve, no limit |
| Power supply rejection | 20 microvolts per volt typical, 60 maximum |
| Input bias current | 50 nanoamps maximum |
| Input offset current | 5 nanoamps maximum |
| Input impedance | 80 kohm non-inverting, 27 kohm inverting, 40 kohm common mode |
| Common mode range | twice the negative supply to twice the positive supply minus 2 volts |
| Common mode rejection | 76 dB minimum, 86 typical |
| Voltage noise | 2 microvolts peak to peak, 90 nanovolts per root hertz at 1 kHz |
| Bandwidth at unity gain | 500 kHz, 50 kHz at a gain of 10 |
| Slew rate | 0.45 volts per microsecond |
| Settling to 0.01 per cent | 90 microseconds on a 10 V step |
| Quiescent current | 570 microamps typical, 700 maximum, 800 over temperature |
| Supply range | 4.5 to 36 volts single, plus or minus 2.25 to plus or minus 18 dual |
| Body | eight pin SOIC |
| Temperature range | minus 40 to plus 85 degrees |
| Catalogue code | INA145UA |
| Grade | UA, the only grade published for this family |
| Carrier | tube and reel, confirm the row on the order |
Gain from 1 to 1000 set by two external resistors
INA145UA is a unity gain difference amplifier with a 40 kohm network on the input and a 10 kohm resistor on the output stage, and the gain is set by a pair of external resistors as 1 plus the ratio of RG2 to RG1. That is the whole appeal: one part covers a strain bridge at 100, a shunt at 10 and a line receiver at 1, and the resistor pair can be a 0.1 per cent network that also sets the bandwidth.
The on-die 0.01 per cent gain error belongs to the unity gain connection. Once external resistors set the gain, their tolerance and their drift enter the error budget directly, and a 1 per cent pair with 100 ppm tracking is what the channel actually gets whatever the amplifier contributes. The external pair also sets the noise gain and the bandwidth, so a gain of 100 turns 500 kHz into 50 kHz and a 0.45 volt per microsecond slew rate into a 4.5 volt per microsecond ramp at the output.
Plus or minus 28 volts of common mode on a plus or minus 15 volt supply
The input common mode range of INA145UA is quoted as twice the negative supply to twice the positive supply minus 2 volts, which on a plus or minus 15 volt supply is minus 30 to plus 28 volts, and on a single 5 V supply is ground to plus 8 volts. Both ends extend beyond the rails, which is what makes the part usable on a high side shunt whose common mode sits above its own supply.
The catch is that the range moves with the output. The vendor specifies the window with the output at zero, and as the output swings towards a rail the usable common mode narrows, because the internal stage runs out of headroom on the same rail. A channel that needs the full window at full output is a different part; a channel that measures a shunt at a fixed common mode and a small differential is exactly the case this window was written for.
570 microamps and a 4.5 volt single supply
INA145UA draws 570 microamps typical, 700 maximum and 800 over temperature, from a single supply between 4.5 and 36 volts or a dual supply between plus or minus 2.25 and plus or minus 18 volts; operation continues down to plus or minus 1.35 volts with reduced specification. On a 4 to 20 milliamp loop with 3.5 milliamps allocated to the electronics, that is a comfortable fit with room for a reference and a converter.
The supply also sets the output window. Into 10 kohm the output reaches to within 0.3 volts of the negative rail and 1.25 volts of the positive at 25 degrees, widening to 0.5 and 1.25 over temperature; into 100 kohm the figures improve to 0.15 and 1 volt. Short circuit current is 15 milliamps continuous and the part is stable into 1000 picofarads, so a cable to a remote sensor does not need a series resistor to keep it quiet.
200 microvolts typical, 1 millivolt maximum, 50 nanoamps of bias
Offset on INA145UA is 200 microvolts typical and 1 millivolt maximum referred to the input, with a drift that the vendor publishes as a curve rather than a limit. Supply rejection is 20 microvolts per volt typical and 60 maximum over the input range, and the offset current is 5 nanoamps against a 50 nanoamp bias current. Those two current figures are what the source impedance works against.
Fifty nanoamps into a 10 kohm bridge impedance is 500 microvolts, half the maximum offset, and into a 100 kohm source it is 5 millivolts, five times the offset. The bias current therefore decides whether the part can be used at all on a high impedance sensor, and the offset current decides how much of that error cancels when the two source resistances match. On a thermocouple or a pH electrode the current path has to be provided deliberately, because a floating source has no return and the input sits wherever leakage puts it.
500 kHz at unity gain, 90 microseconds to settle at 0.01 per cent
The bandwidth of INA145UA is 500 kHz at a gain of 1 and 50 kHz at a gain of 10, with a slew rate of 0.45 volts per microsecond and a settling time of 40 microseconds to 0.1 per cent and 90 microseconds to 0.01 per cent on a 10 V step. Overload recovery from a 50 per cent overdrive is 40 microseconds, which is the same order as the settling time and worth remembering when a multiplexer switches channels.
At 0.45 volts per microsecond a 10 V step takes 22 microseconds of ramp before any settling starts, so the 90 microsecond figure is consistent rather than pessimistic. Sixteen channels at that rate is 1.4 milliseconds per scan, about 700 scans per second, which is fine for temperature and pressure and far too slow for a vibration or audio channel. The gain trades directly against this: at a gain of 100 the bandwidth is 5 kHz and the scan rate falls by an order of magnitude.
80 k and 27 k: an asymmetric input impedance
The input impedance of INA145UA is 80 kohm on the non-inverting input, 27 kohm on the inverting input and 40 kohm common mode, which is not symmetric and cannot be made symmetric by the user. The asymmetry means that a source impedance in series with each input creates a different divider on each side, and the difference appears as a gain error and as a common mode to differential conversion that no amount of trimming at zero removes.
Two practical consequences follow. Keep the two source impedances equal, including any protection resistor, any filter capacitor feed and any multiplexer on resistance, because 1 kohm of mismatch against a 27 kohm input is already 3.7 per cent. And keep the source impedance low: 1 kohm against 27 kohm is a 3.6 per cent signal loss on that side, which is three hundred times the amplifier's own gain error and belongs in the calibration, not in the amplifier specification.
Five hundred and seventy microamps makes this a loop powered candidate, and the 4.5 V single supply floor means a 5 V rail works without a boost. Our lead time page covers the case where the part is quoted long, and the amplifier cross reference page covers the fixed gain parts that can replace it where the external pair is not wanted.
Does the external resistor pair change the common mode range? No. The vendor states that gains above unity set with an external pair do not affect the common mode input range, because the attenuator that defines the range sits ahead of the gain stage. That is the property that makes the part usable on a high side shunt at any gain.
Is the 0.01 per cent gain error valid at a gain of 100? No. That figure belongs to the unity gain connection, where the on-die 10 kohm resistor sets it. At a gain of 100 the external pair dominates, and its tolerance is the number that goes on the requirement.