Contact Us

INA141U

Brand: Texas Instruments
Texas Instruments INA141U is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA141U — Power Management & Signal Chain | Superb Automation

INA141U

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA141U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA141U: a gain of 10 or 100 from a jumper, in the tight bin and the eight pin SOIC

The INA141U is a precision instrumentation amplifier whose gain is 10 V/V with pins 1 and 8 open and 100 V/V with them shorted. There is no gain resistor, so there is no resistor tolerance, no placement and no drift term from a passive. The U bin carries the tighter offset window: 100 µV maximum at a gain of 10 and 50 at a gain of 100, with 2 µV per degree of drift at a gain of 10 and 0.5 at a gain of 100.

The part runs on 750 µA, holds 200 kHz at a gain of 100 because its input stage is current feedback, and settles to 0.01 per cent in 7 microseconds at a gain of 10 and 9 at a gain of 100. On a temperature transmitter, a medical front end or a process analyser channel that needs one of two gains, it removes a resistor from the bill and a calibration step from the line.

The INA141U rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback input
Vendor statusActive, production
Data sheetSBOS052B, revised January 2026
Addendum rowINA141U, 75 pieces per tube
GradeU bin, 100 µV maximum at a gain of 10
Gain10 V/V with pins 1 and 8 open, 100 V/V with them shorted
Gain error0.05 per cent maximum at a gain of 10, 0.075 at a gain of 100
Input offset voltage100 µV maximum at a gain of 10, 50 at a gain of 100
Offset drift2 µV per degree at a gain of 10, 0.5 at a gain of 100
Input bias current5 nA maximum
Voltage noise12 nV per root hertz at a gain of 10 on the SHE flow, 15.1 on TID
Common mode rejection117 dB minimum at a gain of 100, 100 at a gain of 10
Bandwidth994 kHz at a gain of 10 on SHE, 610 on TID, 200 kHz at a gain of 100
Settling7 µs at a gain of 10, 9 µs at a gain of 100
Output swing1.4 V from each rail on SHE, 0.15 V on TID
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current750 µA typical on SHE, 590 on TID
BodySOIC, D outline, 8 pins, 4.9 by 6 mm
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees

A gain of 10 or 100 from a jumper, not a resistor

INA141U sets its gain from the connection between pins 1 and 8 rather than from an external resistor: open, the gain is 10 V/V, shorted, it is 100 V/V. There is no gain resistor to buy, place, tolerance or drift, and the gain error is 0.05 per cent maximum at a gain of 10 and 0.075 per cent at a gain of 100 on the U bin, with a 10 ppm per degree drift. On a channel that has to be 10 or 100 and nothing else, that is the tidiest arrangement in the catalogue.

The jumper is not free of resistance. The vendor states that 0.5 ohm in the connection reduces the gain by 0.1 per cent, so a 2 ohm trace and a 1 ohm via are 0.4 to 0.6 per cent, which is ten times the trimmed gain error. The short should be a wide trace directly between the two pins, or a 0 ohm link placed on the pin centres, and the connection should be checked on the first article rather than assumed.

SHE and TID: one part number, two different chips

The same order code can come from either of two fabrication flows, and on INA141U the flows differ in almost every row that matters. Offset at a gain of 10 is 100 microvolts maximum on SHE and 80 on TID for the U bin, bandwidth is 994 kHz against 610, output swing is 1.4 V from each rail against 0.15 V, voltage noise at 1 kHz is 12 against 15.1 nanovolts per root hertz, and quiescent current is 750 against 590 microamps. None of that appears in a distributor listing.

The output swing difference is the one that breaks boards. A part specified to swing within 1.4 V of the rails on a plus or minus 5 V supply stops at plus or minus 3.6 V, which is not enough for a 4 V full scale signal, while the other flow reaches plus or minus 4.85 V. A channel checked against the headline number and built with the other flow fails at the top of its range, and the failure looks like a gain error rather than a headroom limit.

750 microamps and 200 kHz at a gain of 100

Quiescent current on INA141U is 750 microamps typical and 800 maximum, on a supply from plus or minus 2.25 V to plus or minus 18 V. That is four times below the INA131 and within a tenth of the INA129, and it comes with a current feedback input stage that holds 200 kHz of bandwidth at a gain of 100, where the INA129 falls from 1.3 MHz at unity gain to 200 kHz at a gain of 100 and keeps falling as the gain rises.

Settling to 0.01 per cent is 7 microseconds at a gain of 10 and 9 microseconds at a gain of 100, with a 4 microsecond recovery from a 50 per cent overload. For a multiplexed front end that is a scan rate of about 100 kilohertz per channel, which is limited by the converter rather than the amplifier. The supply current is quoted with the input at zero volts, so a channel driving a heavy load draws more through the output stage.

100 microvolts on the U and 250 on the UA at a gain of 10

The offset bin is the first thing to read on INA141U: at a gain of 10 the U bin is 100 microvolts maximum and the UA bin 250, and at a gain of 100 they tighten to 50 and 125 because the offset is referred to the input and the gain multiplies it. Drift follows the same split, 2 microvolts per degree against 2.5 at a gain of 10 and 0.5 against 1.5 at a gain of 100. The chip flow moves these numbers again by up to 20 per cent.

On a 10 mV full scale bridge at a gain of 100 the output full scale is 1 V and the 50 microvolt input offset is 5 mV at the output, half a per cent, which is trimmed once. The drift of 0.5 microvolts per degree is 50 microvolts at the output over 100 degrees, a tenth of a per cent, which is not trimmed and is usually acceptable. On the UA bin both numbers double, which is the difference between a calibrated instrument and a monitored one.

40 V of protection and 117 dB of rejection at a gain of 100

The inputs of INA141U survive 40 V beyond either rail, and the protection is internal, so an input wired to a live 24 V loop with the amplifier unpowered does not destroy it. Common mode rejection is 117 dB minimum at a gain of 100 on the U bin, 110 on the UA bin, and 100 and 93 dB at a gain of 10, measured with a 1 kohm source imbalance at plus or minus 13 V. Rejection rises with gain because the input stage, not the output stage, does the work.

The common mode range is 2 V inside each rail with the output at zero, so on a plus or minus 15 V supply the window is plus or minus 13 V at that output level and narrows as the output swings. On a single 5 V supply the window is small and a mid rail reference is mandatory. Input impedance is 100 Gohm differential in parallel with 2 pF, so a high impedance sensor is not loaded by the amplifier.

The D body, a tube of 75 and a reel of 2500

INA141U is an eight pin SOIC at 4.9 by 6 mm, sold in a 75 piece tube at moisture level 3 and on a 2500 piece large reel under the slash 2K5 suffix, both active in the current addendum. The load capacitance limit is 1000 pF and short circuit current is 20 mA continuous to mid supply, so the output drives a cable with a series resistor and does not drive a speaker. Gain of 10 or 100 is set by the jumper, so one part covers two ranges and the reel covers both.

Because the gain is set by a pin connection rather than a resistor, the same reel can build a gain of 10 board and a gain of 100 board, which simplifies stock. The cost is that the gain is not adjustable and the two values are six times apart, so a channel that needs 30 has to change part. The 0.5 ohm rule also means the jumper is a real component on the bill of materials and should be treated as one rather than as a copper bridge drawn at the last minute.

Buying INA141U

The gain is set by a connection rather than a resistor, so the same reel builds a gain of 10 board and a gain of 100 board, which is a real stock simplification on a product family with two ranges. The connection has to be treated as a component: 0.5 ohm in the short reduces the gain by 0.1 per cent, which is twice the trimmed gain error, so a thin trace and a via are not acceptable.

The chip origin is the other half of the buying question. Offset, bandwidth, output swing, noise and supply current all move between the SHE and TID flows on the same order code, and the output swing difference of 1.4 V against 0.15 V is the one that breaks a low voltage product. Our traceability report page covers how a lot record carries the flow.

Questions that arrive with this part number

Whether the gain can be anything other than 10 or 100 is the first question, and it cannot: the two values are set by the internal network and a connection, and a channel that needs 30 is a different part with a gain resistor. The second is whether the UA grade can stand in, and the answer is that the offset window widens to 250 µV at a gain of 10 and 125 at a gain of 100, which is still inside most budgets.

The third is the output swing. A part that stops 1.4 V short of each rail on a plus or minus 5 V supply reaches only plus or minus 3.6 V, so a 4 V full scale signal does not fit even though the supply does. That is the single most common surprise on this part and it is on the second page of the sheet rather than the first.