Contact Us

INA129UA-2K5

Brand: Texas Instruments
Texas Instruments INA129UA-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA129UA-2K5 — Power Management & Signal Chain | Superb Automation

INA129UA-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA129UA-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA129UA-2K5: the A grade reel under the hyphen spelling, and the two numbers to quote on the order

The INA129UA-2K5 is the hyphen spelling of the A grade reel row, which the addendum prints as INA129UA/2K5 at 2500 pieces. The hyphen is a catalogue artefact rather than a different part, and the two strings normalise to one addendum row, one body, one marking and one moisture level. The order should carry the piece count and the carrier as words so that the separator cannot decide the quantity.

The part is the UA bin of the INA129: 10 nA of bias current, 110 dB of rejection at a gain of 100, 8 nV per root hertz of noise, 700 µA of supply current and a 49.4 kΩ gain network that makes it a drop in replacement for a competing part. Offset is 1000 µV divided by gain maximum, which at unity gain is the loosest reading on the sheet and at a gain of 100 is 10 µV.

The INA129UA-2K5 rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback input
Vendor statusActive, production
Data sheetSBOS051G, revised January 2026
Addendum row it normalises toINA129UA/2K5, 2500 pieces
GradeA suffix
Gain equationG = 1 + 49.4 kΩ divided by RG
Input offset voltage1000 µV divided by gain maximum
Offset drift1 µV per degree divided by gain maximum
Input bias current10 nA maximum
Input protectionPlus or minus 40 V without damage
Common mode rejection110 dB minimum at a gain of 100
Bandwidth1.3 MHz at unity gain, 200 kHz at a gain of 100
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current700 µA typical
BodySOIC, D outline, 8 pins
Carrier2500 pieces on a large reel
Moisture levelLevel 3, 168 hour floor life
Temperature rangeMinus 40 to plus 125 degrees

Tubes, reels and two different moisture levels

The SOIC rows ship 75 pieces in a tube or 2500 pieces on a large reel, and the DIP rows ship 50 pieces in a tube. The carrier decides the handling, not the part: a 75 piece tube is a prototype or a small build, and a 2500 piece reel is a production run that will take months to consume. Between those two there is nothing on the addendum, which is why a build of 500 boards is usually bought as several tubes and hand fed rather than as a partial reel.

The moisture level differs between the carriers on this family. The tube rows are published at level 2 with a one year floor life, and the reel rows at level 3 with a 168 hour floor life, so the same die has a different shop floor rule depending on how it arrived. A level 3 reel that is opened for a partial build has to go back into dry storage or be baked, and a 2500 piece reel can easily sit open across two builds. Reading the level off the label rather than off the part number is the practical control, and INA129UA-2K5 is the code to check it against.

The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm

The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.

The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA129UA-2K5 the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.

50 µV of offset and half a microvolt per degree

The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA129UA-2K5 can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.

The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.

Gain error rows, the A grade and the 0.024 per cent window

Gain error on this family is quoted per gain setting and per grade, and the tightest row is 0.024 per cent at a gain of 1 on the A grade parts. That figure is smaller than the tolerance of the resistor that sets the gain, so the resistor, not the amplifier, is what a calibration adjusts. At a gain of 100 the family rows widen and the A grade still holds a window about half as wide as the plain grade, which is the practical difference between the two bins on a channel that is calibrated once rather than per unit.

Nonlinearity is 0.001 per cent of full scale on the plain grade and 0.0005 per cent on the A grade, which is well below any converter this part is likely to drive. The number that limits a real channel is the gain drift, quoted in ppm per degree, because it cannot be trimmed at the bench and it moves with the cabinet temperature. On INA129UA-2K5 the drift row is the one to put in a specification that has to hold over temperature, and the room temperature gain error row is the one to put in a production test limit.

Plus or minus 40 V of input protection and the bias current return path

The inputs survive 40 V beyond the rails without damage, which covers the ordinary fault of a transducer cable being plugged in while the rack is powered, and it covers a miswired bridge. It does not cover a sustained fault at the supply pin, and it does not protect the source: a 40 V fault drives current through the protection network and into whatever is driving the amplifier, so a series resistor at the connector is still worth the board space. The protection also stops being transparent above roughly a megohm of source resistance.

The bias current return path is the second half of the input requirement. Each input needs a dc path to a defined potential, and a floating source such as a transformer or a capacitive sensor will let the inputs drift until the amplifier saturates. The vendor shows the ordinary arrangements, and the one to avoid on INA129UA-2K5 is a path through a high value resistor on one leg only, because that converts the bias current into a differential offset. Matched paths on both legs, or a path to the reference rather than to ground, keep the error common mode.

120 dB of common mode rejection and the source imbalance that removes it

The common mode rejection row is 120 dB minimum on the family, measured with a 1 kΩ source imbalance, and it is the number that decides whether a bridge channel can reject a 50 Hz disturbance. Rejection degrades with source imbalance at roughly 1 dB per 100 Ω above the test condition, so a channel with a 10 kΩ mismatch between the two input legs has thrown away most of the 120 dB. In practice that mismatch comes from the sensor rather than from the board: a 350 Ω bridge with one leg 5 Ω high, or a thermocouple with a 2 kΩ cable resistance on one side only.

The fix is a pair of matched resistors at the input, or a buffer for each leg, or a sensor with a trimmed output impedance. The REF pin is part of the same problem: the vendor notes that 8 Ω in series with REF is enough to degrade rejection on a typical part, so the reference has to be driven from a low impedance source such as an amplifier or a shunt reference with a capacitor, not from a divider alone. On INA129UA-2K5 the rejection also falls with frequency, and the vendor curve of rejection against frequency is the one to read for a switching supply disturbance rather than the dc row.

Buying INA129UA-2K5

Two numbers belong on the order line: the piece count and the moisture level. The separator is not one of them, because both spellings reach the same reel row and a supplier who confirms the hyphen against a drawing that carries the slash is confirming the same part. Where the drawing and the addendum disagree on a suffix, the addendum is the authority and the drawing needs a deviation note.

The second decision is whether the reel is the right carrier at all. On a first build the 75 piece tube is usually enough and avoids a level 3 reel being opened for twenty parts, and on a production line the reel is the only sensible quantity. Our lead time page covers the schedule side, and the safety stock page covers how much of a reel to hold against a line that runs monthly.

Questions that arrive with this part number

Whether the hyphen spelling is a second item is the first question, and it is not: it resolves to INA129UA/2K5. The second is whether the A grade reel can be swapped for the U grade reel in a shortage, and it can only after the offset budget is checked, because the window doubles in the direction that matters.

The third is the bias current on a high impedance source. At 10 nA and a 100 kΩ source the error is 1 mV, which is the same size as the offset window at unity gain and dominates it at a gain of 100. A source above a few tens of kΩ needs the bias current counted first and the offset second, which is the opposite of the order most budgets are written in.