Contact Us

INA129U

Brand: Texas Instruments
Texas Instruments INA129U is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA129U — Power Management & Signal Chain | Superb Automation

INA129U

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA129U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA129U: the plain grade eight pin SOIC with the 49.4 kΩ gain network

The INA129U is the plain grade of the eight pin SOIC body in a 75 piece tube, and it is the production friendly member of the family that carries the 49.4 kΩ gain network. The 4.9 mm by 6 mm body runs on the reflow line, the tube covers a first build, and the gain equation G = 1 + 49.4 kΩ divided by RG means an existing resistor table gives the expected gain without a change.

The electrical rows are the family rows: 50 µV maximum offset, 0.5 µV per degree drift, 5 nA of bias current, 8 nV per root hertz of noise, 120 dB of common mode rejection, 700 µA of quiescent current, 1.3 MHz at unity gain and 200 kHz at a gain of 100, on a supply from plus or minus 2.25 V to plus or minus 18 V. The inputs survive 40 V beyond the rails, which covers a transducer plugged in while the rack is live.

The INA129U rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback
Vendor statusActive, production
Data sheetSBOS051G, revised January 2026
GradePlain, the family offset and gain error rows
Gain equationG = 1 + 49.4 kΩ divided by RG
Gain range1 to 10,000 V/V
Input offset voltage50 µV maximum
Offset drift0.5 µV per degree maximum
Input bias current5 nA maximum on the standard rows
Voltage noise8 nV per root hertz at 1 kHz, 0.2 µV peak to peak from 0.1 to 10 Hz
Common mode rejection120 dB minimum
Bandwidth1.3 MHz at a gain of 1, 200 kHz at a gain of 100
Input protectionPlus or minus 40 V without damage
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current700 µA typical
BodySOIC, D outline, 8 pins, 4.9 by 6 mm
Carrier75 pieces per tube
Reel siblingINA129U/2K5, 2500 pieces on a large reel

Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ

The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.

Because of that, INA129U must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.

700 µA of quiescent current across a plus or minus 2.25 V to 18 V window

INA129U draws 700 µA typical, which is four times the current of the micropower INA126 and a twentieth of what a fully featured instrumentation amplifier usually costs. The supply window of plus or minus 2.25 V to plus or minus 18 V covers a plus or minus 15 V industrial rack and a plus or minus 2.5 V single cell analogue front end in the same part number, and the common mode range tracks the rails rather than sitting at a fixed offset from ground.

The current is flat with load and nearly flat with temperature, so the supply budget can be set from the data sheet row rather than measured. What is not in the row is the reference divider and the load current. A plus or minus 15 V part driving a 10 kΩ load at 10 V adds a milliamp, which is more than the amplifier, and a single supply channel with an unbuffered mid rail divider can add a quarter of a milliamp. The amplifier is therefore rarely the largest item in the budget, and the budget is still small enough that a battery instrument can afford two channels.

The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm

The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.

The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA129U the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.

Current feedback input stage and bandwidth at a gain of 100

The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA129U serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.

Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.

8 nV per root hertz of voltage noise against 0.17 pA of current noise

The voltage noise row is 8 nV per root hertz at 1 kHz and the current noise is 0.17 pA per root hertz on the standard rows, which places the crossover source resistance at about 47 kΩ. Below that the voltage noise dominates and the amplifier is as quiet as the source; above it the current noise dominates and a FET input part would be quieter. On a 350 Ω bridge the voltage noise is the whole story and 8 nV per root hertz over a 10 Hz bandwidth is 25 nV, which against a 10 mV full scale is 2.5 parts per million.

The 0.1 to 10 Hz noise is quoted as 0.2 µV peak to peak, which is the figure that matters for a slow channel: a 10 mV full scale signal with 0.2 µV of low frequency noise has a resolution floor of 20 parts per million, better than most 16 bit converters can use. A channel that needs more resolution than that is limited by the sensor, and the amplifier stops being the item to change. On INA129U the noise is flat enough that a higher gain does not improve the input referred figure below the crossover.

Settling time against gain on a multiplexed front end

The settling time curve on this family is the one to read before a channel is put behind a multiplexer. At a gain of 100 the part settles to 0.01 per cent in a few microseconds, which allows a scan rate in the tens of kilohertz; at a gain of 1000 the same figure stretches out and the scan rate falls with it. The stage before the converter has to settle from the previous channel's value, not from zero, so the worst case is a full scale step between two adjacent channels, and that is the step the vendor curve uses.

The other half of the settling budget is the multiplexer and the filter between it and the amplifier. A 1 kΩ series resistor with a 100 nF capacitor has a 100 µs time constant, which dominates the amplifier completely and is the usual reason a scan runs slower than the data sheet suggests. On INA129U the settling figure is only useful when the input network in front of it is faster than the amplifier, and a channel that ignores that rule will show an inter-channel error that moves with the source impedance.

Buying INA129U in the tube

Seventy five pieces suits a first build and a bench that wants the SOIC body without a reel. The buying question that matters on this code is the gain equation: the 49.4 kΩ network exists to match a specific resistor table, so a substitution to the 50 kΩ code is a drawing change rather than a purchasing choice. That should be settled before the order, not after a calibration fails.

The second question is the grade. The plain bin is right when the channel has a trim or the full scale is large enough that 50 µV is a small fraction of it. On a 10 mV full scale the offset is half a per cent of range, which is inside most specifications, and the A grade is only worth buying when it removes a trim operation. Our amplifier cross reference page lists the compatible codes and the grades we compare.

Questions that arrive with this part number

Whether the U and the /2K5 codes carry the same part is the first question and they do, with the carrier and the moisture level as the differences. The second is whether this code can replace the INA128U, and it cannot on an existing board without recalculating the gain resistors, because the two equations differ by 1.2 per cent at a gain of 100.

The third is about the bandwidth at the working gain. On a channel scanned at 20 kHz the 200 kHz at a gain of 100 is enough headroom, and on a channel scanned at 200 kHz it is not, whatever the settling curve suggests. The multiplexer and the input filter usually set the real limit, and the amplifier is the second thing to check rather than the first.