Contact Us

INA126U

Brand: Texas Instruments
Texas Instruments INA126U is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA126U — Power Management & Signal Chain | Superb Automation

INA126U

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA126U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA126U: the plain grade SOIC body in a 75 piece tube

The INA126U is the plain grade of the eight pin SOIC body in a 75 piece tube, which makes it the prototype and small build carrier of this family. Seventy five pieces is three tubes of twenty five in practice, enough for a few hundred channels with spares, and small enough that a reel is not worth opening. The tube also survives a bench environment better than a reel does, because it can be resealed and it does not need a feeder to use.

On the electrical side the plain grade carries the family rows: 250 µV maximum offset, 3 µV per degree drift, 25 nA bias current, 175 µA per channel and a gain floor of 5. The part runs from plus or minus 1.35 V to plus or minus 18 V, so it covers a battery instrument and a plus or minus 15 V rack with the same code, and the two op amp topology is what keeps the supply current low enough for the first of those.

The INA126U rows as the addendum publishes them

Part classMicropower instrumentation amplifier, two op amp, single channel
Vendor statusActive, production
Data sheetSBOS062D, revised December 2025
GradePlain, the family offset and gain error rows
Gain equationG = 5 + 80 kΩ divided by RG
Gain range5 to 10,000 V/V
Input offset voltage250 µV maximum
Offset drift3 µV per degree maximum
Input bias current25 nA maximum
Common mode rejectionSpecified per gain and per source imbalance in the vendor table
Bandwidth200 kHz at a gain of 5, 9 kHz at a gain of 100, 1.8 kHz at 500
Settling to 0.01 per cent30 µs at a gain of 5, 160 µs at 100, 1.5 ms at 500
Supply rangePlus or minus 1.35 V to plus or minus 18 V
Quiescent current175 µA typical, 200 µA maximum per channel
BodySOIC, D outline, 8 pins
Carrier75 pieces per tube
Moisture levelLevel 2, 260 degrees, one year floor life
Temperature rangeMinus 40 to plus 85 degrees

Two op amp topology and why the gain floor is 5

The INA126 is a two op amp instrumentation amplifier rather than the three op amp arrangement used by the larger instrumentation parts, and that choice explains most of what is unusual about it. The first stage is a pair of amplifiers sharing one gain resistor, and the second stage is a difference amplifier that removes the common mode. Fewer amplifiers means less supply current, and it also means the gain cannot go all the way down: the minimum stable gain is 5, and the vendor states that a minimum circuit gain of 5 is what keeps the dc common mode range and the bandwidth usable. On INA126U there is no resistor value that gives unity gain, so a channel that needs a buffer is a different part.

The gain equation is G = 5 + 80 kΩ divided by RG, which is a different shape from the 1 + 50 kΩ form used by the INA128 family. The five is inside the equation, so the external resistor only ever adds to a gain that is already 5. At a gain of 100 the resistor is 842 Ω, at a gain of 1000 it is 80.4 Ω, and at the top of the range the resistor is a couple of ohms, which is where the resistance of the socket and the wiring starts to matter as much as the resistor itself.

250 µV of offset and 3 µV per degree of drift on a bridge channel

The offset row for this family is 250 µV maximum on the plain parts and tighter on the A grade, and the drift row is 3 µV per degree maximum. Against a 10 mV full scale bridge those numbers are 2.5 per cent of range and 0.03 per cent per degree, so the offset is trimmed at the bench and the drift is lived with. Against a 100 mV full scale the offset is a quarter of a per cent and the drift is negligible, which is the region where the part is comfortable and where most pressure and flow transmitters actually sit.

The comparison that matters is against the amplifier the part replaces. A general purpose op amp pair built into an instrumentation front end can easily carry 1 mV of offset and 10 µV per degree, and at that level the drift, not the bridge, sets the annual recalibration interval. Moving to a trimmed instrumentation amplifier buys the interval back. The other half of the budget is the bridge excitation: a 5 V excitation on a 350 Ω bridge draws 14 mA, which is two orders of magnitude more than INA126U draws, so the current budget is set by the sensor rather than by the amplifier.

Bandwidth that falls with gain: 200 kHz at 5, 9 kHz at 100

The bandwidth row is quoted at three gains on this family: 200 kHz at a gain of 5, 9 kHz at a gain of 100 and 1.8 kHz at a gain of 500. That is a steep fall, and it is the price of running the input stage at 175 µA. For a pressure or temperature channel sampled a few times a second it is irrelevant. For a vibration channel or a multiplexed data acquisition front end it is the number that decides whether the part can be used at all, and it has to be read at the gain the channel actually runs rather than at the gain in the headline.

Settling follows the same curve: 30 µs to 0.01 per cent at a gain of 5, 160 µs at a gain of 100 and 1.5 ms at a gain of 500, with a 4 µs overload recovery from a 50 per cent overdrive. On a multiplexed front end the settling time, not the bandwidth, sets the channel scan rate, because the amplifier has to recover from the previous channel before the converter samples. A 16 channel scan at a gain of 100 therefore runs at a few kilohertz at best, and a board that assumes otherwise will show crosstalk that looks like a converter fault.

175 µA per channel and the supply window that comes with it

At 175 µA per channel typical and 200 µA maximum, INA126U is built for a product that runs from a battery or from a loop supply, and the supply window of plus or minus 1.35 V to plus or minus 18 V is what makes that possible. The bottom of the window is low enough that a pair of fresh alkaline cells in series will run the part directly, and the top is high enough for a plus or minus 15 V industrial rack. Nothing in between needs a regulator, which is the point: a channel that does not need a regulator does not need the quiescent current of one either.

The current is quoted per channel and with no load, so the total for a dual INA2126 is twice the figure. What the number does not include is the reference divider. A single supply channel needs a mid rail reference, and a 10 kΩ divider across 5 V draws 250 µA, which is more than the amplifier itself. A 100 kΩ divider draws 25 µA and needs a capacitor to hold it stiff; that trade is made once per board rather than once per channel, and it decides whether the microamp budget survives.

The 80 kΩ term, 0.1 per cent resistors and the resistance you forgot

Gain accuracy on INA126U is set by the external resistor and by the 80 kΩ term inside the equation, and the internal term is trimmed. What is not trimmed is the resistance from the RG pins to the resistor itself: the socket, the solder joint, the trace and the resistor lead all sit in series with RG, and at a gain of 1000 where RG is 80 Ω a single ohm of that path is 1.25 per cent of gain error. That is why the vendor note says sockets and wiring resistance matter at high gain, and why the resistor should be placed within a few millimetres of the pins.

The resistor itself should be a 0.1 per cent metal film part with a 25 ppm per degree coefficient, and it should be the same type on every channel of a multi channel board so that the channels track rather than each drifting its own way. A 1 per cent resistor at a gain of 100 contributes 1 per cent of gain error before temperature, which is larger than the amplifier gain error row. The cost difference between a 1 per cent and a 0.1 per cent resistor is a few cents, and it is the cheapest accuracy in the whole channel.

Input range, output swing and the 1000 pF load limit

The output stage of INA126U swings to within about 0.75 V of the positive rail and 0.8 V of the negative rail at the quoted load, and it is stable into 1000 pF. That capacitance limit is the one that catches boards in the field: a cable from the amplifier to a remote indicator is easily a nanofarad, and an amplifier driving a cable without a series resistor will show a step response with a tail that looks like a settling problem. A 100 Ω series resistor at the output isolates the capacitance and costs nothing in a high impedance load.

The input range depends on the common mode voltage and on the differential signal at the same time, which is why the vendor prints it as a graph rather than as a single number. On a plus or minus 15 V supply and a gain of 100 the input window is wide; at a gain of 5 it is wider still, because the input stage has more headroom when it is not amplifying. A channel that has to measure a signal sitting near the positive rail at high gain will clip in the input stage before the output saturates, and the symptom is a reading that stops rising rather than one that pins.

Buying INA126U in tubes

Seventy five pieces is a carrier for a prototype and a nuisance for a production run, so the decision is usually made by the build size rather than by the price. A run of 300 boards with one channel each needs four tubes and a spare, which is a single purchase order; a run of 3000 boards needs forty tubes and a counting operation at receiving. At that point the reel rows of the same die are the cheaper carrier and the same electrical part is available on them.

The plain grade is the right choice when the offset is trimmed at the bench or when the full scale is large enough that 250 µV is a small fraction of it. For a 10 mV full scale the plain grade consumes 2.5 per cent of the range before trimming, and the A grade consumes half of that, so the grade question is a question about the trim circuit. Our amplifier cross reference page lists the grades and the second sources we compare when a bin cannot be found.

Questions that arrive with this part number

Whether the tube can be resealed and reused is the first question, and it can as long as the desiccant is replaced and the level 2 indicator has not changed colour. The second is whether the plain grade can be upgraded to the A grade on the same board, and it can: the die, the pinout and the footprint are identical, and the only change is a tighter offset window that a calibration will not notice.

The third question is about the supply. The plus or minus 1.35 V floor is real but the common mode window narrows with it, so a battery instrument at 3 V total has about a volt of usable signal swing and has to be referenced to mid rail. A channel that expects a rail to rail amplifier will be disappointed by the 0.75 V of headroom the output gives up at each rail.