Contact Us

INA126EA-2K5

Brand: Texas Instruments
Texas Instruments INA126EA-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA126EA-2K5 — Power Management & Signal Chain | Superb Automation

INA126EA-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA126EA-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA126EA/2K5: a micropower instrumentation amplifier in an eight pin VSSOP on a reel

The INA126EA/2K5 is the A grade of the single channel micropower instrumentation amplifier in the eight pin VSSOP body, supplied 2500 pieces on a large reel. The catalogue string uses a hyphen where the vendor prints a slash, so INA126EA-2K5 and INA126EA/2K5 are the same orderable part, and a system that matches strings exactly will need both forms recorded.

The family is the lowest power instrumentation amplifier in this part of the catalogue: 175 µA per channel, a supply range from plus or minus 1.35 V to plus or minus 18 V, a 250 µV maximum offset, 3 µV per degree drift, 35 nV per root Hz of noise, 25 nA of bias current and a gain from 5 to 10,000 with one external resistor. The two op amp topology is what makes the supply current possible, and the same die is used in the dual channel INA2126.

The INA126EA/2K5 rows as the addendum publishes them

Part classMicropower instrumentation amplifier, two op amp
Vendor statusACTIVE, production data
Data sheetSBOS062D, revised December 2025
Catalogue stringINA126EA-2K5, vendor prints INA126EA/2K5
Gain equationG = 5 + 80 kΩ divided by RG
Gain range5 to 10,000 V/V
Quiescent current175 µA per channel
Supply rangePlus or minus 1.35 V to plus or minus 18 V
Input offset voltage250 µV maximum
Offset drift3 µV per degree maximum
Input bias current25 nA maximum
Input noise35 nV per root Hz
BodyVSSOP, DGK outline, 8 pins
Carrier2500 pieces on a large reel
Smaller carrierINA126EA/250, 250 pieces on a small reel
Other bodiesINA126P and PA in PDIP, INA126U and UA in SOIC
Moisture levelLevel 2, 260 degrees, one year floor life
Temperature rangeMinus 40 to plus 85 degrees
Part markingA26

The moisture row is the notable one: level 2 with a one year floor life against level 3 with 168 hours on the other bodies. That is a property of the VSSOP package's smaller cross section, and it makes the VSSOP the easiest of the three bodies to hold as stock. A build that has moved from the SOIC to the VSSOP for board area gets a moisture budget twenty times longer as a side effect.

Three bodies for one die and how to choose between them

The family ships in PDIP (P), SOIC (D) and VSSOP (DGK), all eight pins, and the electrical rows are the same. The choice is board area against handling: the VSSOP is roughly half the footprint of the SOIC and needs a finer placement nozzle and a stencil aperture that a coarser process cannot print. A board with a 0.5 mm pitch part in the same assembly already has the process for it; a board that has nothing finer than 1.27 mm is taking on a new process for the sake of a few square millimetres.

The PDIP body remains the prototyping body and the repair body. A socketed DIP can be changed without a rework station, and a programme that is still in its first hundred units is better served by the DIP and a later board revision than by committing to a fine pitch process immediately.

A micropower part on a bipolar supply

The supply range from plus or minus 1.35 V to plus or minus 18 V is wide, and a plus or minus 1.35 V floor means the part runs from two AA cells without a converter. That is unusual and useful: a portable instrument with a plus or minus 1.5 V rail from a pair of cells has a signal range of about plus or minus 1.2 V, which is enough for a bridge with a 10 mV full scale and a gain of 100.

At the top of the range the part runs on plus or minus 15 V and can take a signal close to the rails, which is why it appears in industrial instrumentation alongside parts that draw ten times the current. The same part in two very different supplies is a sign of a topology that does not depend on the supply for its behaviour.

Gain, noise and the 175 µA trade

At 35 nV per root Hz the noise is between the 20 nV of a three op amp part and the 60 nV of the single supply micropower family. That places the part in the middle of the range: good enough for a bridge with a millivolt full scale, not good enough for a low level transducer at high gain. A gain of 100 channel with a 10 mV full scale produces 1 V, and the input referred noise in a 10 Hz bandwidth is about 11 µV, which is 0.11 per cent of the full scale.

The 175 µA is per channel, and the dual INA2126 is 350 µA for two, which is the same per channel figure. A four channel board built from two duals draws 700 µA, and that is the number that goes into the battery budget rather than the single channel figure multiplied by four with a rounding error.

Buying INA126EA/2K5

The reel is active, the grade is the A bin, and the small reel at 250 pieces is available for a smaller build. The string has a hyphen in this catalogue and a slash at the vendor, and both should be recorded so that a search on either form finds the part. The part marking A26 is what a receiving inspection reads when the label is not trusted.

The VSSOP body is the one to choose when board area matters and the assembly house can place 0.65 mm pitch parts. For a build that cannot, the SOIC sibling carries the same die and a level 3 rating. Our NPI production launch checklist page covers the first article checks for a fine pitch part, and the amplifier cross reference page lists the micropower families we compare.

Placing a VSSOP part without a fine pitch process

An eight pin VSSOP has a 0.65 mm pitch, which is within reach of a modern line and beyond a stencil that was cut for 1.27 mm parts. A board that has nothing finer than an SOIC is taking on a new stencil, a new aperture set and a new inspection step for the sake of a footprint that is about half the area. The saving is real on a dense board and imaginary on a board with space around it.

The inspection question is the one that decides. A 0.65 mm pitch joint can be inspected visually with a low power microscope, and an x ray is not needed for a gull wing part. A line that has the microscope and the training can place the part; a line that does not will find the bridging at functional test rather than at inspection.

The VSSOP body is the right choice for a compact multi channel instrument where four or eight channels have to fit on a small board, and the wrong choice for a single channel board that has room for an SOIC. The electrical rows are identical, so the decision is mechanical rather than electrical.

One last point on the marking: A26 is the marking on this body, and it is what a receiving inspection reads when the reel label is in doubt. A part with a different marking is a different grade or a different die, and the difference is invisible in a photograph of the reel.

Questions that arrive with this part number

Whether the hyphen and the slash are the same part is the first question, and they are: the vendor prints INA126EA/2K5 and this catalogue prints INA126EA-2K5. Whether the 250 piece small reel is the same die is the second, and it is, with a different carrier and the same marking. The third is the minimum gain of 5, which is set by the two op amp topology and cannot be configured around.

The fourth is the moisture level, which on this body is level 2 with a one year floor life, so the dry storage arrangement is simpler than for the SOIC and the DIP does not need one at all.