Contact Us

INA125PA

Brand: Texas Instruments
Texas Instruments INA125PA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA125PA — Power Management & Signal Chain | Superb Automation

INA125PA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA125PA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA125PA: the A grade of the amplifier with an integrated bridge reference

The INA125PA is the A grade of the plastic DIP member of this family: the same die, the same four reference taps, the same 460 µA and the same 16 pin body, with the tighter of the trimmed offset bins. It is the part to specify when the bridge channel has no trim and the offset has to hold at its factory value, which on a 10 mV full scale bridge means the difference between a channel that meets its zero specification and one that does not.

The integrated reference is the reason the family exists. A separate reference and amplifier can be matched on paper and will still drift apart in a cabinet, and the two parts also cost board area, a decoupling network and a second qualification. Putting both functions on one die removes all three, at the cost of a pin count and a fixed set of reference voltages.

The INA125PA rows as the addendum publishes them

Part classInstrumentation amplifier with precision voltage reference
Vendor statusACTIVE, production data
Data sheetSBOS060
GradeA suffix, tighter trimmed offset bin
Reference voltages1.24 V, 2.5 V, 5 V, 10 V by pin strap
Gain equationG = 4 + 60 kΩ divided by RG
Gain range4 to 10,000 V/V
Input offset voltage250 µV maximum, family row
Offset drift2 µV per degree maximum
Input bias current20 nA maximum
Common mode rejection100 dB minimum
Quiescent current460 µA
Supply rangeSingle supply 2.7 V to 36 V
BodyPDIP, N outline, 16 pins
Carrier25 pieces per tube
Sleep pinDedicated, shuts the amplifier and the reference
Moisture levelNot applicable to this package type
Temperature rangeMinus 40 to plus 85 degrees

Twenty five pieces in a tube is a small carrier and a 16 pin DIP is a large part, so the logistics are awkward in both directions. A programme that needs 500 parts is buying twenty tubes, and the receiving inspection has to count tubes and verify labels rather than rely on a single reel count. That is a cost of the package, not of the grade, but it appears in the same quotation.

Why the grade matters more here than on a plain amplifier

A bridge channel has two error sources that a plain amplifier channel does not: the bridge offset itself and the amplifier offset. The bridge offset is usually larger and is trimmed at the sensor, and the amplifier offset is what remains. On a 10 mV full scale with a 250 µV amplifier offset the residual is 2.5 per cent, which is a large number to leave in a channel that is otherwise trimmed.

The integrated reference changes the arithmetic in a useful way. Because the excitation and the amplifier share a die, a ratiometric measurement cancels the reference drift and leaves the amplifier offset and drift as the errors that matter. The A bin reduces the offset term, and the 2 µV per degree drift sets the floor: over 40 degrees that is 80 µV, which is 0.8 per cent of a 10 mV scale. A channel specified to 0.5 per cent over temperature needs either a narrower temperature range or a different front end.

Driving the bridge from the on chip reference

The four taps are accurate but they are not power stages. A 350 Ω bridge at 2.5 V draws 7 mA, which is well beyond what the reference will deliver directly, so the circuit either uses a higher resistance bridge, a lower excitation, or an external pass transistor driven from the reference. The pass transistor approach keeps the accuracy of the reference and adds a device and a compensation capacitor, and it is the standard arrangement in industrial transmitters.

The alternative is to excite the bridge from the supply and use the reference only for the converter, which gives up the ratiometric cancellation. That is a legitimate choice when the supply is well regulated and the bridge is a low current type, and it is a decision that should be made explicitly rather than by default.

Sleep, settling and a battery powered transmitter

The sleep pin turns off the amplifier and the reference together, and the wake up behaviour is dominated by the reference. A bandgap with a 1 µF output capacitor takes a few milliseconds to settle, and a circuit that reads the converter 500 microseconds after waking will read a reference that has not arrived. The delay should be measured on the first article and put into the control software as a constant, not left to a loop that happens to be slow enough.

The duty cycle arithmetic is what makes the part work in a battery product. Four hundred and sixty microamps continuously is 18 days on a 200 mAh cell; at a 1 per cent duty cycle the same cell lasts years, and the limit becomes the sleep current and the leakage of the surrounding circuit. That is a strong argument for this family in a field transmitter and a weak one in a mains powered instrument, where the 460 µA is simply a small load.

Buying INA125PA

The part is active in a 25 piece tube, and the SO-16 siblings carry the same die if the board is reflowed. The grade should be named on the order, because the plain P row is the same body and carrier and the two are indistinguishable without reading the marking. The reference taps are a functional choice and not an orderable option, which means a build that needs the 10 V tap has to check the supply rather than the part number.

For a bridge instrument our incoming inspection plan page covers the checks we run on tubes of this size, and the amplifier cross reference page lists the bridge front ends we compare when a specific grade is not available.

Socket or solder in a field instrument

A 16 pin DIP in a socket can be replaced in the field with a screwdriver, which matters for an instrument mounted on a machine where a service visit costs more than the part. The cost is contact resistance and corrosion: a socket adds a few milliohms and, in a humid cabinet, a leakage path near the input pins that a soldered joint does not have. On a bridge channel with a 20 nA bias current, a leakage path of a few hundred megohms in the socket is a measurable offset.

The practical rule is that a socket belongs on a board that will be serviced and a soldered part belongs on a board that will be sealed. A transmitter that is potted cannot be serviced at the socket anyway, so the socket adds risk without benefit, and a bench instrument that is recalibrated annually gets real value from it.

The gain resistor on a bridge channel is a fixed part, and its tolerance is usually absorbed by the bridge calibration rather than by the resistor. A 0.1 per cent part is still worth the cents on a channel that is calibrated once, because it keeps the calibration range narrow and the production test simple.

Questions that arrive with this part number

Whether the A grade is a different reference as well as a different amplifier is the first question, and it is not: the reference is the same on both rows and the grade applies to the amplifier's offset bin. Whether the reference can be used on its own without the amplifier is the second, and it can, because the reference output is a pin, but the quiescent current is then 460 µA for a function that a 3 µA shunt reference would do better.

The third question is the 2.7 V supply floor. A 3 V rail works with the 2.5 V tap and a 350 Ω bridge at reduced excitation, and a 5 V tap needs a rail above 6 V. The fourth is the pin count, which prevents a swap with an eight pin amplifier in either direction.