Contact Us

INA122PA

Brand: Texas Instruments
Texas Instruments INA122PA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA122PA — Power Management & Signal Chain | Superb Automation

INA122PA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA122PA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA122PA: the A grade of the single supply micropower amplifier in a DIP

The INA122PA is the A grade of the plastic DIP member of this family. The die, the two op amp topology, the 60 µA supply current and the rail to rail output are all shared with the plain part; the A suffix marks the tighter of the trimmed bins, and the tube of 50 is the same carrier. On a portable instrument that has no trim network the grade is the only thing standing between the channel and a 250 µV offset at its worst.

The reason this part matters is that a battery instrument rarely has room for a calibration step. The offset is what it is at the factory, the drift is what it is over temperature, and the circuit either tolerates both or fails. A tighter bin is a cheap way to buy tolerance at the front end of a channel that will never be adjusted.

The INA122PA rows as the addendum publishes them

Part classSingle supply micropower instrumentation amplifier, two op amp
Vendor statusACTIVE, production data
Data sheetSBOS069B
GradeA suffix, tighter trimmed bin
Supply range2.2 V to 36 V single or dual
Quiescent current60 µA
Output swingRail to rail
Gain equationG = 5 + 200 kΩ divided by RG
Gain range5 to 10,000 V/V
Input offset voltage250 µV maximum, family row
Offset drift3 µV per degree maximum
Input bias current25 nA maximum
BodyPDIP, P outline, 8 pins
Carrier50 pieces per tube
RoHS rowsPlain, A and G4 rows listed separately
Moisture levelNot applicable to this package type
Temperature rangeMinus 40 to plus 85 degrees

The G4 row deserves a sentence. It is the same part with the green material declaration, and it appears as its own orderable row, which means a customer who requires a specific material declaration has to order that row rather than assume the plain one carries it. On a medical or automotive build the declaration is part of the approval package, and a part that is electrically identical but documented differently holds up a release.

What a two op amp stage costs in common mode range

With a single supply the negative rail is the natural reference, and the first stage of a two op amp instrumentation amplifier is a follower that can sit at the negative rail. What it cannot do is sit near the positive rail while the output is high, because the follower's own output has to drive the second stage. The result is a common mode range that depends on the output voltage, and the vendor publishes it as a curve rather than a number for that reason.

On a 5 V supply with a 2.5 V reference the signal sits near mid rail and the range is comfortable. On a 2.2 V supply with a signal that swings to 2 V the same part is at the edge, and the failure is a gain that falls off at the top of the range rather than an obvious clipping. A review that plots the input common mode against the output swing for the worst case signal is the way to catch it, and it takes ten minutes with the vendor curve.

A 25 nA bias current in a battery instrument

25 nA is a thousand times the bias current of a FET input part, and it is still small enough for most bridge and thermocouple work. Into a 100 kΩ source it is 2.5 mV of offset, which is ten times the amplifier offset and would dominate a millivolt channel. Into a 1 kΩ bridge leg it is 25 µV, which is negligible. The part therefore belongs behind a low impedance source, and the datasheet application circuits show exactly that: bridge amplifiers with a few hundred ohms of source resistance.

Matching the two input resistances halves the error, because the bias currents are similar and cancel in the differential pair. That is the reason a bridge circuit with four equal resistors is such a good match for this amplifier, and the reason a single ended thermocouple with a long lead is not.

Sleep, duty cycle and the real power number

The part has no shutdown pin, so the 60 µA is drawn continuously. On a duty cycled instrument the supply has to be switched externally, and a load switch or a transistor in the supply line adds its own leakage. The arithmetic that matters is the total charge per measurement rather than the quiescent current: 60 µA for 10 ms is 0.6 microcoulombs, which is negligible against the charge a radio or a display uses, so the amplifier is rarely the reason a battery fails.

Where the 60 µA does matter is a continuously powered sensor node that measures once a minute and has no other load. There the amplifier is a large fraction of the average current, and a lower power part or a duty cycled front end is worth the engineering effort. The decision is a system one and the amplifier's data sheet only supplies one input to it.

Buying INA122PA

The part is active in a 50 piece tube. The three rows, plain, A and G4, are separate orderable strings and a purchase order that names only the base string can receive any of them. For a build that has a material declaration requirement, naming the G4 row is the only way to be sure.

For the DIP itself, the supply question is whether the board will ever be reflowed. A DIP in a battery instrument built in tens of units is fine; a DIP in a product built in thousands is a process cost that the SOIC sibling removes. Our incoming inspection plan page covers how we check a mixed shipment of these three rows, and the amplifier cross reference page lists the single supply families we compare.

Material declarations and the G4 row

The G4 row exists because a customer sometimes needs the green material declaration as a separate orderable item rather than as a property of the plain row. On a medical build the declaration is part of the device file, and a part that is electrically identical but documented differently holds up a release even though nothing on the board changes. Ordering the G4 row is the only way to be certain which declaration travels with the shipment.

The second document that matters on a portable instrument is the traceability record: the lot, the date code and the country of assembly. A part bought from channel stock has a date code that may be years old, and an instrument with a five year service life wants a date code that leaves solderability margin. Asking for the date code at quotation time is cheaper than discovering it at the reflow oven.

One more point on the 50 piece tube: the tube itself is the handling risk on an eight pin DIP, because a tube that is tipped out onto a bench presents the pins to whatever the bench carries. An ESD mat and a grounded wrist strap are the standard precautions, and a DIP with a 4 pA input is more sensitive to a charged plastic bag than the data sheet's ESD rating suggests, because the damage shows as a leakage current rather than a dead part.

Questions that arrive with this part number

Whether the A grade is a different die is the first question, and it is not: same die, tighter test. Whether the part can drive a 10 kΩ load to the rail is the second, and the output does swing rail to rail but the current available near the rail is limited, so a heavy DC load will pull the swing in. The third question is the reference pin, which sets the output zero and can be tied to a divider to centre the output in the range.

The fourth is the missing shutdown pin. A customer who expects a sleep mode will not find one on this part, and the honest answer is that the supply has to be switched externally or the part left running.