INA121P
Product Specifications
INA121P
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA121P from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA121P: a FET input instrumentation amplifier that draws 450 µA in an eight pin DIP
The INA121P is the plastic DIP member of a FET input instrumentation amplifier family, and its defining pair of numbers is a 4 pA input bias current against a 450 µA quiescent current. That combination is unusual: most parts that reach picoamp bias current pay for it with a milliamp of supply current, and most parts that run on half a milliamp have a nanoamp of bias current. The 4 pA is what lets the part sit in front of a high impedance source such as a pH electrode or a piezoelectric sensor without loading it, and the 450 µA is what lets the same part run from a battery pack for a year.
The gain is set by one external resistor from 1 to 10,000, the topology is current feedback so the bandwidth holds up at high gain, and the inputs withstand 40 V of abuse. The plain P suffix carries no grade letter beyond the package, which means the offset and drift rows are the family rows rather than a tightened bin.
The INA121P rows as the addendum publishes them
| Part class | FET input instrumentation amplifier, three op amp, current feedback |
| Vendor status | ACTIVE, production data |
| Data sheet | SBOS078 |
| Gain equation | G = 1 + 50 kΩ divided by RG |
| Gain range | 1 to 10,000 V/V |
| Gain error | Plus or minus 0.5 per cent, family row |
| Input offset voltage | Plus or minus 200 µV |
| Offset drift | Plus or minus 2 µV per degree |
| Input bias current | Plus or minus 4 pA |
| Input noise at 1 kHz | 20 nV per root Hz at a gain of 100 |
| Common mode rejection | 106 dB |
| Quiescent current | 450 µA |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Input protection | Plus or minus 40 V without damage |
| Body | PDIP, P outline, 8 pins |
| Carrier | 50 pieces per tube, rails |
| SOIC sibling | INA121U and INA121UA in the D body |
| Moisture level | Not applicable to this package type |
| Temperature range | Minus 40 to plus 85 degrees |
| Pinout | Same eight pin pinout as the SO-8 member |
The 50 piece tube is the row that decides how the part is bought. A DIP is a through hole part, so it is either hand inserted or run on a line with a tube feeder, and 50 pieces is a small multiple for a production build. A run of 500 boards needs ten tubes, and the receiving inspection should count tubes rather than pieces because the tube is the carrier the vendor ships and a short tube is the failure mode that shows up as a missing board at the end of a batch, not at receiving.
Picoamp bias current and a 500 µA budget in the same part
Bias current doubles roughly every ten degrees on a FET input stage, so the 4 pA figure at 25 degrees is a starting point rather than a constant. At 70 degrees the same part can be drawing tens of picoamps, and into a 10 MΩ source that is hundreds of microvolts of offset drift that the data sheet drift row does not describe. A channel that has to hold its offset at 70 degrees either keeps the source resistance low, matches the two input resistances, or moves to a part with an even lower bias current. The formula is the same in all three cases: the error is the bias current times the difference between the two source resistances.
The 450 µA quiescent current is quoted for the amplifier alone, and the external gain resistor does not change it. What does change the total is the reference divider: a two op amp or three op amp instrumentation amplifier used single supply needs a mid rail reference, and a divider that draws 100 µA to hold that rail is a fifth of the amplifier budget. A 10 kΩ divider across a 5 V rail draws 250 µA, which is more than half the amplifier current, and a buffer on that divider costs another amplifier. Choosing the reference network before the amplifier is the way to keep the total in the microamp range.
Current feedback and why bandwidth survives a gain of 1000
A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, because the loop gain falls as the closed loop gain rises. This family uses a current feedback stage and holds a much flatter bandwidth curve, which is why a part with 450 µA of supply current still settles in microseconds at a gain of 100. The trade is sensitivity to the feedback impedance: the gain resistor should be a metal film part with short leads placed close to the RG pins, and a wirewound or a long leaded resistor will put a step in the response that a sine sweep does not reveal.
The gain equation G = 1 + 50 kΩ divided by RG is exact only at DC. At a gain of 1000 the resistor is about 50 Ω, and at that value the pin and lead inductance of the package is a measurable fraction of the impedance, so the AC gain is slightly higher than the DC gain and the step response shows peaking. The vendor curve of gain against frequency for common gain settings is the reference, and a channel at a gain above 1000 should be checked on a step rather than trusted from the equation.
The DIP body in a world of SOIC assembly lines
A PDIP part is easy to prototype and awkward to produce. The through hole pins need plated holes, the insertion is manual or needs a tube feeder, and the wave solder or selective solder step is a separate process from the reflow line that does the rest of the board. On a mixed board with a handful of DIP parts the cost is a second process, and that cost is usually larger than the difference between the DIP and the SOIC part price. The same family exists in the SO-8 body with the same die and the same pinout, so a board that has to move to reflow can change package without changing the circuit.
The reason to stay with the DIP is thermal or mechanical rather than electrical: a socketed DIP can be replaced in the field without a rework station, and a DIP has more lead length to absorb a mismatch between the board and a connector. A probe amplifier that is swapped during calibration is a genuine case for the socket, and a production board that never sees a soldering iron after test is a case for the SOIC.
Buying INA121P
The part is active, the carrier is a tube of 50, and the body is the plastic DIP. The purchase order needs the P suffix and nothing more, but the quotation should say which grade is being quoted, because the same family is also sold as the A suffix in the same package with a tighter offset bin. A customer who signs a specification that quotes 200 µV and receives the A grade has more margin than expected and no complaint; a customer who signs for the A grade and receives the plain part has a channel that fails its offset budget at incoming test.
For a long running programme the risk is not the price, it is the tube. A DIP in a tube is the carrier least likely to be held in stock by a distributor, because the volume of the market moved to SOIC long ago, and a programme that needs 200 pieces a year is buying from whatever is in the channel. That is the point at which an annual buffer against a known schedule is cheaper than an expedite, and our component lead time page describes how we set that buffer, while the amplifier cross reference page lists what we compare when a tube cannot be found.
Questions that arrive with this part number
Whether the P and the U are interchangeable is the first question, and electrically they are: the same die, the same pinout, the same data sheet. The difference is the package and the carrier, and a board that has been laid out for one will not take the other without a footprint change. Whether the part can run from a single 5 V rail is the second, and it cannot in the ordinary sense: the supply range is plus or minus 2.25 V upwards, which means a bipolar supply or a single supply with a mid rail reference and a signal that stays inside the amplifier common mode range.
The third question is whether the 40 V protection makes an external clamp unnecessary. It protects the amplifier from damage, not the source from the amplifier, and it does not stop the fault current from disturbing the measurement while it lasts. A series resistor and a pair of diodes at the connector are the standard answer, and the resistor value is chosen against the bias current error rather than against the fault current.