Contact Us

INA118UB

Brand: Texas Instruments
Texas Instruments INA118UB is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA118UB — Power Management & Signal Chain | Superb Automation

INA118UB

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA118UB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA118UB: the B grade of the low power precision family in a SOIC

The INA118UB is the B grade of the INA118 family in the eight pin SOIC, and it is active while the plastic DIP B grade is last time buy. The die is the three amplifier instrumentation amplifier with 50 µV of maximum offset, 0.5 µV per degree of drift, 5 nA of maximum bias current, 110 dB of minimum common mode rejection at a gain of 1000, 40 V of input protection, and 350 µA of quiescent current on a supply range from 2.25 V to 18 V.

The carrier is a tube of 75 pieces and the reel of the same body ships 2500. The moisture level is level 3 with a 168 hour floor life, the temperature range on the addendum is minus 40 to plus 85, and the body marking is the same 118U string as the A grade, which is the traceability point worth knowing before a mixed stock is issued to a line.

The INA118UB rows as the addendum publishes them

Part classThree amplifier instrumentation amplifier, B grade, low power, surface mount
Vendor statusACTIVE, production data
Data sheetSBOS027C, revised September 2022
Input offset voltage50 µV maximum on the B row
Offset drift0.5 µV per degree maximum
Input bias current5 nA maximum
Common mode rejection at G = 1000110 dB minimum
Input overvoltage protection40 V without damage
Supply range2.25 V to 18 V total
Quiescent current350 µA
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to 10,000 V/V
BodySOIC, D outline, 8 pins
Carrier, tube row75 pieces in a tube
Carrier, reel row2500 pieces on a large tape and reel
RoHSYes
Lead finishDirected to the vendor on this row
Moisture levelLevel 3 at 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees
Part markingThe same 118U string as the A grade, no letter on the body
Revision rowINA118UB.A and INA118UB.B, both active
Green rowA G4 suffix row with the same body and quantity
Alternative bodyPlastic DIP B grade, last time buy

The marking is the point a receiving inspection has to handle deliberately. The body does not carry a B, so the only record of the grade is the reel or tube label and the accompanying paperwork. A warehouse that opens a tube and tips the parts into a bin has destroyed the traceability of the grade, and on a channel that was specified around a 50 µV offset that is a real risk rather than a paperwork one.

Why the grade matters more than the body

The A and B grades of this family differ by an offset bin and by the price, and the body is a packaging choice. On a channel with a 100 mV full scale the two grades are indistinguishable after a trim, and on a channel with a 10 mV full scale the grade decides whether the channel meets its target without a trim. The body decides how the part is assembled, and the two decisions are independent, which is why the catalogue carries four combinations.

Where a customer is moving from the plastic DIP to the SOIC, the grade should move with the body. A board that was qualified on the B grade and rebuilt with the A grade because the SOIC A grade was in stock will pass a room temperature test and fail a cold start, and the failure will be attributed to the new board rather than to the grade.

Offset drift over the operating range

The drift of 0.5 µV per degree is the largest term in the error budget of an untrimmed channel over temperature. Over the minus 40 to plus 85 range that is 62 µV, which is more than the maximum offset of the part itself. A channel specified to 0.1 per cent on a 50 mV full scale has a 50 µV budget, and the drift alone exceeds it, so the specification cannot be met by the grade or by a trim alone; it needs either a narrower temperature range or a different amplifier.

That arithmetic is worth doing before a grade is chosen, because customers often specify a tight accuracy over the full industrial range without checking whether the drift budget allows it. The honest answer in that case is a chopper stabilised amplifier with a drift in the nanovolt per degree range, and the trade is noise and switching artefacts rather than accuracy.

The eight pin SOIC on a two layer board

An eight pin SOIC is small enough that the routing around it is the whole thermal and noise story. The two input pins are adjacent, so the guard trace between them is short and the leakage path is short with it. The gain resistor sits between two pins on the same side, so a 505 Ω resistor can be placed within a millimetre, which is where it needs to be at high gain.

On a two layer board the ground plane is on the bottom, and the reference pin should connect to it at a single point under the part rather than by the shortest path to a via somewhere else. A reference that shares a return path with the output current picks up the output current as an error, and on a 350 µA part with a 1 mA load the error is a millivolt.

Buying INA118UB

The tube is 75, the reel is 2500, and both are active. The B grade on this body is the combination a new precision board should use, because the DIP B grade is last time buy and the A grade may not meet a low level target without a trim. The premium over the A grade is small against the cost of a trim step.

A customer who already has stock of the A grade should check whether the channel is trimmed before switching to the B grade. If it is trimmed, the switch buys nothing; if it is not, the switch is the cheaper way to reach the accuracy target.

Questions that arrive with this part number

The first is whether the UB and the U are different dies. They are the same die in different bins, and the marking does not distinguish them. The second is whether the reel row carries the same bin, and it does, with the same marking problem.

The third is whether the part can be used at a gain of 1 with the gain resistor left open. It can, and the offset specification at unity gain applies without a trim.

For a customer specifying a grade on a new board, our amplifier cross reference page lists the bins and bodies we compare, and the incoming inspection page sets out how a grade is verified when the body marking does not carry it.

A final point on the grade and the converter. A 50 µV offset on a 10 mV full scale is 0.5 per cent, and a 16 bit converter with a 10 mV full scale resolves 0.15 µV per count, so the offset is 330 counts of the converter's range. That is why a channel of this kind is trimmed at the converter rather than at the amplifier: the trim can be done in the digital domain with a single calibration point, and it costs nothing in parts. Where the trim is done that way, the grade premium buys only the drift, and the drift is 62 µV over the industrial range regardless of bin.

That arithmetic leads to a simple rule for this family: buy the A grade where the channel is trimmed digitally, and buy the B grade where it is not. The rule holds across the DIP and the SOIC bodies, and it is the reason the two bins have coexisted for so long without one displacing the other.