Contact Us

INA118U2K5

Brand: Texas Instruments
Texas Instruments INA118U2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA118U2K5 — Power Management & Signal Chain | Superb Automation

INA118U2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA118U2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA118U2K5: the 2500 piece reel of the low power precision amplifier

The INA118U2K5 is the reel quantity of the INA118U, 2500 pieces on a large tape and reel in the eight pin SOIC. The die is the three amplifier instrumentation amplifier with 50 µV of maximum offset, 0.5 µV per degree of drift, 5 nA of maximum bias current, 110 dB of minimum common mode rejection at a gain of 1000, 40 V of input protection, 350 µA of quiescent current and a gain range from 1 to 10,000.

The string as the addendum prints it carries a slash between the body letter and the quantity, and the catalogue entry on this page does not carry the slash. That is a formatting difference rather than a different part, but it matters at order entry, because the vendor matches on the full string and a stripped version can fail to match or match a neighbouring row.

The INA118U2K5 rows as the addendum publishes them

Part classThree amplifier instrumentation amplifier, precision, low power, reel quantity
Vendor statusACTIVE, production data
Data sheetSBOS027C, revised September 2022
Input offset voltage50 µV maximum
Offset drift0.5 µV per degree maximum
Input bias current5 nA maximum
Common mode rejection at G = 1000110 dB minimum
Input overvoltage protection40 V without damage
Supply range2.25 V to 18 V total
Quiescent current350 µA
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to 10,000 V/V
BodySOIC, D outline, 8 pins
Carrier2500 pieces on a large tape and reel
Reel diameter330 millimetres on the large reel rows
RoHSYes
Lead finishStated as directed to the vendor on this row
Moisture levelLevel 3 at 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees
Part marking118U with the vendor prefix
Revision rowINA118U/2K5.A and .B, both active
Green rowA G4 suffix row with the same quantity, marked as green material
Quantity arithmetic2500 pieces is 2500 boards at one part per board, or 625 at four

The G4 suffix is the green material declaration and it sits on a row of its own in the addendum. A customer with a material requirement should quote the G4 row rather than assume the plain row carries the declaration, and the two rows have the same quantity and the same body so the carrier does not change.

Reel arithmetic for a low power family

A reel of 2500 against a tube of 75 is 33 tubes. A build of two hundred boards a year with one part each consumes a reel every twelve years, which is longer than the part will be active, and in that case the tube is the only sensible buy. A build of three hundred boards a month consumes a reel every eight months, which is a steady rhythm and the right shape for a reel.

The moisture level is what makes the difference in handling. A reel that is opened for an eight month build stays inside a dry cabinet between runs, and the floor life clock only matters when the reel is out of the cabinet. A reel that is opened for a two week run and then left on a shelf is a reel that needs a bake every time, and the bake log becomes part of the build record.

The 2500 piece reel and the pick and place line

A 330 millimetre reel fits a 13 inch feeder, which is the standard on most surface mount lines. A line with an 8 inch feeder needs the reel to be rewound, which breaks the seal and starts the clock, and the rewound reel may not track properly in the feeder. The check is cheap and it happens before the order, not after.

The tape width and the pocket size are set by the eight pin SOIC body, and the standard is the same as any other SOIC-8 in the catalogue. A line that already runs a SOIC-8 part does not need a new feeder setup, which is one of the reasons this body is the practical one for a new board.

Gain resistors across a 2500 piece build

A reel of amplifiers means a reel of gain resistors, and at a gain of 100 the resistor is 505 Ω with a 0.1 per cent tolerance for a 0.1 per cent gain error. A 2500 piece build consumes 2500 resistors, which is a single small reel, and the two reels should be kitted together so that a build does not start with one and stop for the other.

The resistor tolerance is the term that dominates a high gain channel, and on a 2500 piece build the resistor cost is comparable with the amplifier cost. A customer who specifies 0.05 per cent resistors at a gain of 1000 is buying a special order part with its own lead time, and that lead time has to be in the plan before the amplifier reel is ordered.

Buying INA118U2K5

The reel is active, the quantity is 2500, and the string carries a slash in the addendum form. A purchase order should quote the addendum form, and a customer whose system strips punctuation should check the resulting string before it is sent.

For a customer who needs fewer than a few hundred pieces, the tube of 75 is the better buy and the reel is a false economy. For a customer with a steady line, the reel is the only carrier that keeps the machine running without a tube feeder.

Questions that arrive with this part number

The first is whether the reel string is the same die as the tube string, and it is. The second is whether the reel is 330 millimetres, and it is on the large reel rows. The third is whether the G4 row is a different part, and it is the same part with a material declaration on the label.

The fourth is whether a partial reel can be returned to stock. It can, and the floor life clock restarts only if the reel goes back into a dry pack with a fresh desiccant.

For a customer planning a reel purchase, our date code page explains how a partial reel is recorded, and the lead time page sets out how a reel is scheduled against a build.

The reel label is the record that matters on a 2500 piece build, because the tube label of a neighbouring row looks identical apart from the quantity. A receiving inspection that scans the label into the build record gets the date code, the quantity and the assembly site in one step, and a build that does not scan it is relying on a handwritten note. On a part where the body marking does not carry the grade, the label is the only grade record, which makes the scan a quality control step rather than an administrative one.

The second point about a large reel is the splice. A 2500 piece reel can contain a splice where the tape was joined, and a pick and place machine that stops at the splice has to be restarted. The splice is marked on the tape, and an operator who knows to expect one will not treat the stop as a fault. On a long run the stop is a few minutes, and on a run that is unattended overnight it can be the difference between a finished build and a half finished one in the morning.

A third point is the desiccant. A 330 millimetre reel with a desiccant pack inside the bag has a finite capacity, and a bag that has been opened and resealed several times will show a humidity indicator card that has turned. The card is the record, and a card that has turned means a bake before the next use regardless of the hours on the floor life clock.

The last point is the ordering pattern. A reel bought against a build that slips by a quarter sits in a bag for three months, which is fine if the bag is sealed and less fine if it is not. A customer with an uncertain schedule should buy the tube and pay the handling cost rather than buy the reel and pay the storage cost.