Contact Us

ALM2402QPWPRQ1

Brand: Texas Instruments
Texas Instruments ALM2402QPWPRQ1 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ALM2402QPWPRQ1 — Power Management & Signal Chain | Superb Automation

ALM2402QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The ALM2402QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ALM2402QPWPRQ1: dual high-current operational amplifier for driving low impedance loads

ALM2402QPWPRQ1 is the amplifier that replaces a discrete op amp plus boost transistor pair on an actuator or a sensor exciter in a HTSSOP body of 14 pins. Each channel delivers 400 mA continuous from a supply of 5 V to 16 V, with a separate supply pin for the output stage so the output swing can be held below the main rail to keep the dissipation off the die. Overtemperature shutdown, current limit, a shutdown pin and an internal radio frequency filter are included, and the part is qualified to AEC-Q100 grade 1.

Order code and package

Order codeALM2402QPWPRQ1
Functiondual operational amplifier, 400 mA continuous per channel
Supply5 V to 16 V, separate pins for the output stage
Shutdownshutdown pin for low quiescent current standby
Protectionovertemperature flag and shutdown, current limit
Filterinternal radio frequency and electromagnetic interference filter
Offset1 mV typical
PackageHTSSOP, 14 pins with thermal pad
Temperature gradeAEC-Q100 grade 1, minus 40 to plus 125 C ambient
Load capabilitystable with large capacitive loads and high equivalent series resistance
DatasheetSLOS912 revision D
Alternative body12-pin leadless DRR with the same die

Electrical parameters that decide the application

Output current400 mA continuous per channel, which is a thermal number as much as an electrical one
Output supplya second supply pin per output stage, so the swing can be capped below the main rail
Dissipation16 V in and 5 V out at 400 mA is 4.4 W per channel, far outside the package without a heatsink
Thermal padthe pad is the heat path, so the copper under it is part of the current rating
Overtemperaturethe flag is shared with the shutdown function on one pin, so reading the flag and holding the part off are the same action
Current limitprotects the output stage during a wiring fault, not the load
Offset1 mV typical, adequate for a bridge exciter, marginal for a precision current loop
Bandwidthset for actuator and sensor excitation rather than for video or intermediate frequency work
Shutdown currentthe shutdown pin is the only way to reach the low quiescent state
PackageHTSSOP 14 with exposed pad, 6.2 C per W junction to case

Points to check before this part goes on a BOM

The 400 mA rating is per channel and it is continuous only while the junction stays inside its limit. Dropping 11 V at 400 mA is 4.4 W; the HTSSOP body with a thermal pad manages that on a board with copper, and does not manage it in still air on a two layer board.

The separate output supply pin is the feature that makes high current practical: running the output stage from 5 V while the amplifier runs from 16 V moves three quarters of the dissipation out of the part and into the upstream regulator, which has a bigger thermal path.

The overtemperature flag and the shutdown input share a pin. A host that wants to read the flag has to drive the pin, and a host that drives it high has already shut the channel down, so the two functions cannot be used at the same time.

A shunt sense resistor in series with the load adds its own drop to the output swing. At 400 mA a 0.1 ohm resistor costs 40 mV and 16 mW, which is acceptable; a 1 ohm resistor costs 400 mV and 160 mW, which is not, and it is also the value that makes the current limit trip early.

The internal filter is there for a harness that picks up radio frequency energy. It does not replace a series resistor and a capacitor at the connector when the load is meters of unshielded cable.

Stability with large capacitive loads is quoted for the part, but the load's equivalent series resistance and the cable inductance still form a resonance with the output. A 100 nF load and a meter of cable can ring at a few megahertz, which is where the series resistor earns its place.

Where this order code fits

Boards driving a resolver or a valve coil compare this part with the higher bandwidth member of the family before fixing the supply. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What limits the 400 mA output? Heat. The die can deliver the current; the package can only pass the resulting watts to the board through the thermal pad, so the ambient and the copper decide the real number.

Can both channels run at full current together? Only with a thermal path sized for 800 mA of output current at the same time, which usually means the output supply well below the amplifier supply.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.