Contact Us

DRV8872DDAR

Brand: Texas Instruments
Texas Instruments DRV8872DDAR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8872DDAR — Power Management & Signal Chain | Superb Automation

DRV8872DDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8872DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8872DDAR: the 3.6 A brushed driver on a 2500 piece reel

The DRV8872DDAR is an eight pin H bridge for one brushed DC motor, published by the vendor as ACTIVE in production data. The operating range is 6.5 to 45 V, the peak drive is 3.6 A, and the two logic inputs are pulse width modulated from 0 to 100 kHz to set speed and decay mode. The die carries four N channel FETs, a charge pump that keeps the high side enhanced at 100 per cent duty cycle, an internal reference that compares against the ISEN pin for current chopping, and a fault output that pulls low on undervoltage, overcurrent or overtemperature. Nothing in that list is unusual until the electrical table is read against a real motor, and that is where most of the questions behind a purchase enquiry start.

The string on this page ends in DDAR, which is the SO PowerPAD body in a large tape and reel of 2500 pieces, moisture level 2 at 260 degrees, lead finish nickel palladium gold, part marking 8872. Two further rows, DDAR.A and DDAR.B, carry the same quantity, the same carrier and the same marking, so a buyer matching a purchase order to a vendor row is looking at three strings that behave identically on the line and differ only in the vendor's internal revision tracking.

The DRV8872DDAR rows as the addendum publishes them

Part classBrushed DC motor driver, one H bridge, PWM control
Vendor statusACTIVE, production data
Data sheetSLVSCZ0C, August 2015, revised July 2016
Operating voltage6.5 V to 45 V on VM
Peak output current3.6 A
RDS(on), high side307 mΩ typical, 360 mΩ maximum at 24 V and 1 A
RDS(on), low side258 mΩ typical, 320 mΩ maximum at 24 V and 1 A
RDS(on), both FETs565 mΩ typical
Supply current3 mA typical, 10 mA maximum at 12 V
Sleep current10 µA at 12 V with both inputs low
Turn-on time40 µs typical, 50 µs maximum
Time to sleep1 ms typical, 1.5 ms maximum
Input thresholds0.5 V low, 1.5 V high, 0.5 V hysteresis
Input current high33 µA typical, 100 µA maximum at 3.3 V
Propagation delay0.7 µs typical, 1 µs maximum
Output dead time220 ns
Current trip reference0.32 V minimum, 0.35 V typical, 0.38 V maximum
PWM off time25 µs fixed
PWM blanking time2 µs
Undervoltage lockout6.1 to 6.4 V falling, 6.3 to 6.5 V rising
Overcurrent trip3.7 A minimum, 4.5 A typical, 6.4 A maximum
Overcurrent deglitch1.5 µs, retry after 3 ms
Thermal shutdown150 to 175 degrees, 40 degrees hysteresis
Fault output low0.5 V at 5 mA sink
BodyHSOP with PowerPAD, 8 pins, 4.90 by 6.00 millimetres
Reel rowDRV8872DDAR, 2500 pieces, large tape and reel, Active
Marking8872 on the eight pin body
Moisture levelLevel 2 at 260 degrees, one year floor life

Two rows on that table decide whether an order can be matched without a conversation. The 2500 piece reel is the only carrier the vendor publishes, so a pilot build of fifty boards comes out of a production reel and the remaining pieces become stock with a date code. The level 2 rating is the second: it allows a year of floor life, which is generous for a part that usually sits in a kitting tray for a week, but it still expires, and an expired reel needs a bake before it goes near a reflow oven.

What the electrical table fixes for a real motor

The 565 mΩ combined resistance is the number that decides how much heat leaves the package. At 1 A the two FETs drop about 0.57 V, and with the body diode conducting during decay the figure rises. The package is 4.90 by 6.00 millimetres with an exposed pad, so the thermal path runs through the pad into copper, and a two layer board with a small pad will reach the 175 degree shutdown earlier than a four layer board with a ground plane under the part. A 24 V, 1 A load is comfortable; a 12 V, 2.5 A load is not, and the difference is thermal rather than electrical.

The current regulation loop compares the voltage on ISEN, which is the low side FET plus an external resistor, against a 0.35 V internal reference. That means the trip point moves with temperature, because the low side resistance moves with temperature: 258 mΩ at 25 degrees becomes roughly a third higher at 125 degrees. A board set to chop at one current when cold will chop at a lower current when hot, and the divider that sets the reference has to be chosen for the hot case if the mechanical envelope depends on it. A 1 per cent resistor on ISEN is worth the cost; a 5 per cent part throws away most of the accuracy the internal reference offers.

The two inputs and the decay modes they select

Both inputs high is brake, both low is coast and also the sleep state, one high and one low drives in one direction. Because both low enters sleep after 1.5 ms, a controller that coasts the motor by pulling both inputs low is actually putting the driver to sleep, and the 40 µs wake time then applies to the next command. On a printer feed roller that is fine; on a mechanism that needs a controlled coast into a detent it is not, and the alternative is to brake with both inputs high and let the current decay through the FETs.

The fixed 25 µs off time sets the chopping frequency, and the 2 µs blanking window sets the minimum on time. Those two numbers bound the ripple current for a given inductance, and they also mean the loop cannot regulate below a certain duty cycle. A small motor with 200 µH of winding inductance at 24 V will show a visible current ramp within one off time; a large motor with 5 mH will look almost flat. Reading the ripple on a current probe at the ISEN pin is the quickest way to see whether the chosen sense resistor and the chosen motor belong together.

Thermal behaviour on a small board

The exposed pad is the only path with a useful cross section, so the copper under the part decides the junction temperature. The vendor's own guidance is a pad soldered to a plane with vias, and the practical version of that advice is four to nine vias of 0.3 millimetre drill inside the pad, connected to an internal ground plane. Without them the pad is a small island and the thermal resistance climbs sharply, which shows up as a driver that shuts down after twenty seconds of stall rather than after two minutes.

The fault pin is the second thermal instrument. It pulls low on thermal shutdown and recovers automatically once the die cools by the 40 degree hysteresis, so a scope on that pin during a stall test tells you whether the limit you hit was current or heat. That distinction changes the fix: more copper for heat, a smaller sense resistor or a lower reference for current.

Buying DRV8872DDAR in small runs and in volume

The reel is 2500 pieces, which is roughly the annual demand of a small instrument programme and one week of demand for a consumer appliance line. Because there is no tube row and no tray row, the minimum purchasable unit is a full reel unless a distributor has broken a reel, and a broken reel carries the risk that the pieces were stored outside the level 2 window. For a fifty piece engineering build, buying a full reel and holding it is usually cheaper than paying a cutting charge on a partial one.

Date code control matters more than price on this part. The 8872 marking is the same across the three reel suffixes, so a receiving inspection that compares the top of the package with the purchase order will find a match only if the inspector reads the label rather than the marking. Our incoming inspection plan records the reel label, the date code and the quantity, and photographs the label against the purchase order line, which is the only durable evidence if a lot later fails.

Questions that arrive before a purchase order

The first is usually whether the part can replace a DRV8871 or an older DRV8870 in an existing board. The pin out differs on the fault and sense pins, so the answer is no for a drop in swap even though the function is the same, and a small board revision is needed. Where the customer needs the same footprint with a different current, the pin to pin page we keep for these families is the fastest place to compare the rows.

The second is availability at the automotive grade. The catalog part and the DRV8872-Q1 share a die, but the automotive row has a higher minimum voltage and a different moisture level, so the two are not interchangeable in a qualified build. The third is the sense resistor value: with a 0.35 V reference and a low side resistance near 0.26 Ω at room temperature, the external resistor has to be small enough that the reference dominates, and a 0.05 Ω part leaves the FET resistance as the larger term.

For a programme that is moving this driver from prototype to production, the useful next reads are the lead time page for the reel position and the incoming inspection plan for the date code record. Both are written for the case where a reel is bought once and consumed over a year.