Contact Us

DRV8835DSSR

Brand: Texas Instruments
Texas Instruments DRV8835DSSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8835DSSR — Power Management & Signal Chain | Superb Automation

DRV8835DSSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8835DSSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8835DSSR: Two 1.5 A H Bridges That Run From a 2 V Logic Rail and an 11 V Motor Rail

DRV8835DSSR is a dual low voltage H bridge motor driver in a WSON (DSS) body of 12 pins. Each bridge delivers 1.5 A and the two can be paralleled for 3 A into one motor, from a motor rail anywhere between 0 V and 11 V while the logic rail runs separately from 2 V to 7 V. The on resistance of a high side and a low side FET in series is about 450 mOhm, so a 0.8 A motor drops roughly 0.3 V across the bridge and the part stays cool in a 2.00 mm by 3.00 mm body with an exposed pad.

Order code and package

Ordering stringDRV8835DSSR
Family documentDRV8835, SLVSAR1, revised 2016
PackageWSON (DSS), 12 pins, 2.00 mm by 3.00 mm with an exposed thermal pad
Reel and packing3000 pieces on a large reel
Lead finish and moistureNIPDAU, level 1 at 260 C with unlimited floor life
Temperature rangeminus 40 to plus 85 degrees
Body marking835
Green optionDRV8835DSSRG4, the same body and reel with the green material set
Motor supply0 to 11 V on VM
Logic supply2 to 7 V on VCC, which also sets the input thresholds
Control modesIN/IN mode and PHASE/ENABLE mode, chosen by wiring
Parallel optionThe two bridges tie together for 3 A into a single winding

Electrical parameters that decide the application

Continuous current per bridge1.5 A maximum
Parallel current3 A with both bridges in parallel
On resistance, high side plus low sideAbout 450 mOhm at a 2 V logic rail
Motor supply range0 to 11 V
Logic supply range2 to 7 V
Supply current, no PWM and no load85 uA typical and 200 uA maximum
Sleep current5 nA with VCC at 0 V and all inputs low
Overcurrent trip3.5 A
Overcurrent retry time1 us
Output rise time300 ns
Input voltage range0 to 11 V on the logic pins, which tolerates a 5 V controller on a 2 V rail
ProtectionUndervoltage, overcurrent and overtemperature, all automatic

Family variants and how they differ

DRV8835This part, two bridges, separate logic rail, 11 V motor rail
DRV8836The same family in a lower current body, 1.5 A with a different pin out
DRV8833Two bridges rated to 10.8 V with a single supply and a lower on resistance
DRV8847Two bridges with a wider supply range and a serial configuration option
DRV8871A single bridge with an internal current limit set by one resistor
DRV8251A single bridge in a larger body for higher current

Points to check before this part goes on a BOM

The split supply is the feature that decides the application. A 1.8 V or 3.3 V controller can drive the inputs directly while the motor runs from a 5 V or 9 V rail, because VM and VCC are separate pins, and the inputs are rated to 11 V so a 5 V logic high on a 2 V VCC is not a problem. Tying VCC to VM works when both are 3.3 V and removes a rail.

Sleep is entered by taking VCC to 0 V, not by a dedicated pin. That means the logic rail has to be switchable, and the sleep current of 5 nA is only reached with every input at 0 V as well. A board that leaves an input floating while the rail is off can leak through the input protection, which is why the vendor asks for all inputs low during sleep.

The 450 mOhm figure is the sum of one high side and one low side FET, so the conduction loss is the square of the motor current times that number. At 1.5 A that is about 1 W in the package, which the 2 by 3 mm body sheds through the exposed pad into the copper under it. A board with two square centimetres of copper on the pad runs far cooler than one with a thin trace.

Overcurrent is a fixed 3.5 A trip with a 1 us retry, so it protects the part from a stalled motor but gives the firmware nothing to read. There is no fault pin, no current sense output and no way to know which bridge tripped. A product that has to report a stall needs an external sense resistor or a driver with a fault output.

The two control modes are a wiring choice, not a register. IN/IN gives one pin per half bridge and allows a brake by driving both inputs high, while PHASE/ENABLE takes a direction and a PWM and is the cheaper option on a controller with few timers. Both modes are described in the same document, and the pins change name, so a board cannot be reworked from one to the other without a new pattern.

Where a low voltage dual bridge fits

A battery powered toy, a small robot, a peristaltic pump or a camera slider runs a 3 V to 9 V motor and a 3.3 V controller, and needs two bridges for two wheels or one bridge plus a spare for a second axis. The 11 V ceiling covers a 2 cell lithium pack at full charge with margin, and the 1.5 A per bridge covers the stall current of a small geared motor for the fraction of a second it lasts.

Paralleling the bridges is the way to one bigger motor. The vendor shows the two outputs tied and the inputs driven together for 3 A, which halves the conduction loss per amp and doubles the current capability in the same body. The two bridges must be driven with the same polarity, otherwise they fight each other through the supply.

What the board has to get right

Two capacitors decide whether the part survives. A 0.1 uF ceramic on VM and another on VCC, both within a few millimetres of the pins, with the VM one rated for the motor rail. A brushed motor generates a commutation spike at every brush transition, and without the capacitor the spike lands on the FET drain and the absolute maximum is reached long before the thermal limit.

The exposed pad is the only thermal path. It has to be soldered to a copper area with vias if the board is multilayer, and the paste pattern matters because a pad that floats on too much paste sits higher and runs hotter. The vendor publishes a stencil recommendation in the package drawing, and it is worth following where the motor current is continuous rather than intermittent.

Where this order code fits

The part suits a battery powered product with a 3 V to 9 V motor, a controller that runs at 1.8 V or 3.3 V, and no need to read a fault. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can I run it from a single 3.3 V rail? Yes, tie VCC and VM together at 3.3 V. The part then has no separate logic rail and the inputs work from the same supply, which is the common arrangement on a small robot.

How do I put it to sleep? Take VCC to 0 V and hold every input low. There is no sleep pin, so the logic rail has to be switchable, and the 5 nA figure assumes the inputs are low as well.

What happens on a stall? The bridge trips at 3.5 A, waits 1 us and tries again, so a stalled motor chatters at the trip point and heats the package. The part has no fault output, so the controller has to infer the stall from the motor not moving.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.