Contact Us

DRV8428PWPR

Brand: Texas Instruments
Texas Instruments DRV8428PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8428PWPR — Power Management & Signal Chain | Superb Automation

DRV8428PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8428PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8428PWPR: A Stepper Driver That Measures Its Own Winding Current and Steps to 1/256

DRV8428PWPR is a microstepping stepper motor driver with integrated current sensing in a HTSSOP (PWP) body of 16 pins. It drives one bipolar stepper from 4.2 V to 33 V with two internal H bridges, and the current sense is inside the package, so the two shunt resistors that normally sit under the bridge are gone. Full scale current is 1 A with a peak of 1.7 A per bridge, the indexer goes from full step to 1/256, and the on resistance of a high side and low side FET in series is 1500 mOhm at 24 V and 25 degrees, which is the number that limits how much current a small body can carry without a heatsink.

Order code and package

Ordering stringDRV8428PWPR
Family documentDRV8428, SLOSE54C, revised July 2022
PackageHTSSOP (PWP), 16 pins with a thermal pad
Reel and packing3000 pieces on a large reel
Temperature rangeminus 40 to plus 125 degrees
Body marking8428
Second body in the documentRTE, a 16 pin WQFN, same die and different footprint
InterfaceSTEP and DIR, plus M0 and M1 for the step mode
Current senseIntegrated, no external shunt resistors
Decay settingOne resistor on DECAY/TOFF, 14.7 kOhm gives 7 us of off time
Logic levels1.8 V, 3.3 V and 5 V inputs
SleepnSLEEP pin, 2 uA in sleep

Electrical parameters that decide the application

Motor supply4.2 to 33 V on VM
Full scale current1 A, with 1.7 A peak per bridge and 0.7 A rms
Full scale accuracyplus or minus 6 per cent
On resistance, high side plus low side1500 mOhm at 24 V and 25 degrees
Undervoltage lockout3.8 to 4.05 V falling with 3.95 V typical and 100 mV of hysteresis
Overcurrent trip1.7 A with a 1.8 us deglitch and a 4 ms retry
Off time settings7 us, 16 us or 32 us, chosen by the resistor on DECAY/TOFF
Supply current, no motor3.8 mA typical and 5.6 mA maximum
Sleep current2 uA
Turn on time0.8 ms typical and 1.2 ms maximum from the rail crossing the lockout
Minimum step pulse500 ns
MicrosteppingFull step through 1/256, set by M0 and M1

Family variants and how they differ

DRV8428PThis part in the HTSSOP body, 16 pins
DRV8428RThe same die in the RTE WQFN body, a different pad pattern
DRV8426A lower current member of the family with the same interface
DRV8434More current per bridge in a larger body, same STEP and DIR interface
DRV8825An older stepper driver that needs external shunt resistors
DRV8889-Q1The automotive member with a serial port and stall detection

Points to check before this part goes on a BOM

Integrated sensing removes two resistors and adds a limitation. Because the current is measured across the FETs rather than across a shunt, the accuracy is plus or minus 6 per cent of full scale, not of the instantaneous value, so at 10 per cent of full scale the error is a large fraction of the number being controlled. An application that needs a precise low current, such as a microstep at 1/256 with a light load, is better served by a driver with a real shunt.

Smart tune is the reason the part exists for a quiet product. The decay mode is adjusted automatically as the motor moves, which compensates for the winding inductance changing with position and for the motor warming up, and it reduces the audible ripple that a fixed mixed decay produces at low speed. The cost is that the current waveform is not a fixed shape, so a current probe trace differs from the calculation.

Three off times are available and the resistor chooses one. 7 us is the fast setting and gives the quietest low speed operation at the price of more switching loss, 32 us is the slow setting and suits a high inductance motor that cannot follow a fast chopper. A motor with 2 mH to 5 mH of inductance per phase is the range where the middle setting is normally right.

The 1500 mOhm on resistance is high enough that the package is the limit, not the silicon. At 1 A the bridge dissipates 1.5 W, which the 16 pin body can only shed through the thermal pad into the copper under it, and the 1.7 A peak rating is a short term number. A continuous 1 A at 24 V needs a copper area on the pad and a board temperature well below the 125 degree limit.

The undervoltage lockout sits at 3.8 to 4.05 V while the motor supply starts at 4.2 V, which leaves only 150 mV of margin. A 5 V rail that sags to 4.1 V under a step load keeps the part alive but drops it out of regulation, and a rail that dips below 3.8 V resets the indexer position. The reference position has to be recovered after any supply event, because the part has no absolute encoder.

Where an integrated sense stepper driver is used

A label printer, a 3D printer extruder, a valve actuator or a laboratory pump runs a small bipolar stepper at 0.5 A to 1 A and needs the board to be small. Removing the two shunt resistors and their sense traces saves a few square millimetres and one analogue problem, and the internal sensing is good enough for a position loop that only needs torque, not an exact current reading.

Spread spectrum clocking is included for products that have to pass an emission test. The chopper frequency is dithered by a small amount so the switching energy spreads over a band instead of sitting on one harmonic, which is the difference between a marginal and a comfortable reading on a conducted emission scan for a product with a long motor cable.

What to check before the order

The body has to be named. The document covers an HTSSOP and a WQFN, both 16 pins, with different pad patterns and different thermal behaviour. The PWPR string is the HTSSOP, and a footprint drawn for the other body will not take it, which is the usual reason a first prototype does not fit.

The second check is the current headroom at temperature. The 1 A full scale is a room temperature number with the pad soldered to a reasonable copper area, and the same board at 85 degrees ambient carries less. A board that runs the part at 1 A continuous in a sealed box needs the thermal number worked out from the board area, not from the headline.

Where this order code fits

The part suits a small bipolar stepper in a printer, a valve or a pump, where the board has no room for shunt resistors and the current loop only needs torque. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does it need external sense resistors? No. The current is measured inside the package, which is what removes the two shunts. The trade is a full scale accuracy of plus or minus 6 per cent rather than the tolerance of a precision shunt.

How do I set the microstep mode? M0 and M1 select the step mode from full step to 1/256, and the indexer handles the winding currents. The pins can be tied or driven, so the mode can change at run time if the controller has two spare outputs.

What limits the current at 24 V? The package. The bridge drops 1500 mOhm, so 1 A dissipates about 1.5 W in a 16 pin body, and the thermal pad plus the copper under it is the only path out.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.