Contact Us

DRV8412DDWR

Brand: Texas Instruments
Texas Instruments DRV8412DDWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8412DDWR — Power Management & Signal Chain | Superb Automation

DRV8412DDWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8412DDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8412DDWR: Two Full Bridges at 3 A Continuous With Cycle by Cycle Current Limit

DRV8412DDWR is a dual full bridge PWM motor driver in a HTSSOP (DDW) body of 44 pins. It drives two brushed motors or one stepper from a supply up to 52 V at 2 by 3 A continuous and 2 by 6 A peak, or 6 A continuous in parallel mode, with 110 milliohm FETs that hold efficiency near 97 percent and a current limit that acts every PWM cycle rather than latching the bridge off.

Order code and package

Ordering stringDRV8412DDWR
FamilyDRV84x2 dual full bridge, document SLES242H revised July 2024
PackageHTSSOP, DDW body, 44 pins, 14 mm by 8.1 mm nominal
Reel and packing2000 pieces on a large reel, NiPdAu lead finish
Moisture levelLevel 3, 260 C peak, 168 hour floor life
Part markingDRV8412
Tube rowDRV8412DDW is printed Obsolete, so the R string is the active packing
Supplies12 V for GVDD and VDD, a separate PVDD up to 50 V for the bridges
Output rating2 by 3 A continuous and 2 by 6 A peak in dual mode, 6 A continuous and 12 A peak in parallel
Voltage rangeOperating supply up to 52 V on the bridge rail
Package thermalThe DDW body is 44 pins with the pad on the bottom for the heatsink path

Electrical parameters that decide the application

On resistance110 milliohm at a junction temperature of 25 C, both high and low side devices
PWM frequencyUp to 500 kHz, which keeps the current ripple small in a low inductance motor
EfficiencyUp to 97 percent at the rated load, which is what allows a smaller supply and heatsink
Current limit modesCycle by cycle limit in dual, parallel and complementary modes, or latching shutdown on the OCL mode
Programming resistorOne resistor on the overcurrent adjust pin sets the limit for every bridge
Ground arrangementAn independent supply and ground pin per half bridge, so a shunt can be fitted in each leg
Protection setUnder voltage, two stage over temperature, overload and short circuit, with a warning output before shutdown
External partsNo snubber and no schottky diode are needed, the body diode and the gate drive handle the recirculation
BootstrapOne capacitor per half bridge, with the value range printed in the recommended table
Minimum pulseA minimum low side pulse width has to be respected so the bootstrap capacitor refills
Logic inputsPWM, direction and reset per bridge, plus the mode pins that select the bridge topology
Fault outputsA fault pin and a separate over temperature warning pin

Family variants and how they differ

DRV8432The same die with the pad on top, 2 by 7 A continuous and 2 by 12 A peak, for a heatsink clamped to the package
DRV8412DDWRG4The same reel under the green material row
DRV8844Four half bridges at 2.5 A when the load is two small motors rather than one large one
DRV8825A stepper driver with the indexer on board when the controller should not generate the sequence
DRV8306A gate driver for external MOSFETs when the current goes beyond what this body can dissipate
DRV8871A single brushed motor driver with integrated current sensing for a smaller load

Points to check before this part goes on a BOM

Two supplies are mandatory. GVDD and VDD need 12 V for the gate drive and the regulators, while PVDD can sit anywhere up to 50 V for the motor. A board that ties them to one rail either overvolts the gate drive or undervolts the bridge, and the mode pins do not make that arrangement work.

The current limit behaves differently by mode. In the cycle by cycle mode the bridge switches off for the rest of the PWM period and comes back on the next one, which keeps a stalled motor in a controlled state. In the latching mode the bridge stays off until it is reset. The mode pins select which one, and a board that copies the resistor values from one mode into the other gets a limit that is not the intended one.

The 3 A continuous figure assumes the pad is soldered to a copper area with vias. At 110 milliohm and 3 A the conduction loss is about 1 W per bridge, and two bridges plus switching loss push the package towards its thermal limit. The over temperature warning pin exists so a controller can back off before the shutdown, and it should be connected rather than ignored.

The minimum low side pulse width is a bootstrap requirement, not a control preference. If the low side never conducts long enough, the bootstrap capacitor does not refill and the high side gate drive sags, which shows up as a loss of torque at very low duty cycles and as a fault at the extreme. A controller that can command a 1 percent duty has to be checked against this.

The independent ground pins are there for shunts and they are not a general purpose Kelvin connection. Each of the four half bridges has its own supply and ground, which lets two motors run from different voltages on one die, but the pins still share the die substrate and the return currents have to be planned. A shunt in each leg is fine, a shunt in the shared return measures the sum.

Two axes and one controller

A robot with two driven wheels, or a gantry with two axes, needs two full bridges and one controller generating four PWM signals. This part takes those four signals, adds the direction and reset lines, and reports back on one fault pin per bridge plus the thermal warning. The parallel mode is available if one axis later needs more current, at the cost of giving up the second bridge.

The 500 kHz switching ceiling is what makes a small motor quiet. Above the audible range the current ripple in the winding is small, the motor does not sing, and the current loop can be closed at a bandwidth that a 20 kHz stage cannot reach. The trade is switching loss, which is why the efficiency figure is quoted at a specific load rather than as a maximum.

What the two protection outputs are worth

The fault pin is a latch that a controller has to clear, and the warning pin is an early indication that the die is heating. Wiring the warning pin to an interrupt lets the firmware reduce the duty cycle or pause motion before the shutdown, which in a medical or a laboratory instrument is the difference between a graceful stop and a dropped sample.

Neither pin tells you which protection acted. Over current, over temperature and under voltage all report on the fault line, and the controller has to infer the cause from the supply measurement and the thermal warning. Systems that need a diagnosis build those two measurements into the board rather than relying on the driver alone.

Where this order code fits

The part is used where two brushed motors or one bipolar stepper need a quiet, efficient PWM stage on a 12 V to 48 V rail, and a stall has to be limited rather than latched. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the two bridges be paralleled for one motor? Yes, in parallel mode the part delivers 6 A continuous and 12 A peak into a single load, with the two bridges switching together. The mode pins select that arrangement and the current limit resistor then sets one limit for the combined bridge.

What happens on a stall? In the cycle by cycle mode the current is limited every PWM period and the motor sits in a controlled stall until the command changes. In the latching mode the bridge turns off and stays off until it is reset. The mode is a board decision made with the mode pins, not a firmware setting.

Is the DRV8432 a drop in replacement? No. It is the same die with the thermal pad on top rather than on the bottom, so the footprint and the assembly method are different, and its current ratings are higher because the heat path is different. A board built for the 8412 cannot take the 8432 without a change.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.