Contact Us

DRV5056Z1QDBZR

Brand: Texas Instruments
Texas Instruments DRV5056Z1QDBZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5056Z1QDBZR — Power Management & Signal Chain | Superb Automation

DRV5056Z1QDBZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5056Z1QDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5056Z1QDBZR: the 200 mV per mT unipolar sensor without compensation

The DRV5056Z1QDBZR is the most sensitive member of the unipolar linear family, at 200 mV per mT with a linear range of about 20 mT. The Z means no magnet temperature compensation, so the sensitivity is fixed and whatever the magnet does over temperature appears in the reading.

At this sensitivity a 10 mT field moves the output 2 V, which covers almost the whole 0.6 V to rail window on a 3.3 V supply. That is a large signal on a small field, and it is the reason the part appears in games controllers, pedals and triggers, where a 5 mm travel has to be resolved into a few hundred counts.

The unipolar response still applies: the output starts at 0.6 V at zero field and rises with a south pole. On a trigger or a pedal the magnet only approaches from one side, so a single direction sensor is the natural fit and the half of the range a bipolar part would give to the negative side is not missed.

Key data for the DRV5056Z1QDBZR

OutputAnalog, ratiometric, 0.6 V at zero field, south pole increases it
Sensitivity200 mV per mT at 5 V, the steepest in the family
Linear rangeAbout 20 mT, so a strong magnet clips early
CompensationNone on the Z version, the sensitivity does not follow magnet drift
Quiescent output0.6 V nominal, 0.535 V to 0.665 V over the window
Bandwidth20 kHz sensing bandwidth
Supply and current3.3 V or 5 V, 6 mA typical and 10 mA maximum

Body, packing and marking data

BodySOT-23, three pins, DBZ outline
Packing3000 pieces on a large reel on the R suffix
FinishTin lead finish, moisture level 2 at 260 C, one year floor life
Marking56Z1 on the body, the only visible marker of the uncompensated die

Why a game controller wants no compensation

In a trigger, the magnet is a small neodymium disc bonded into a moving plunger, and the travel is a few millimetres. The field changes very little over the operating temperature of a handheld, so compensation would add an error rather than remove one. The Z part is the simpler choice and the one the application notes usually show.

The same logic applies wherever the field is generated electrically rather than by a permanent magnet. A coil or a current carrying conductor does not lose field as it warms in the way a ferrite does, so a part that raises its sensitivity with temperature would misreport the current as the board heats up.

Where the magnet is a bonded or sintered ferrite on a mechanism that runs hot, the A1 or A2 part is the better answer even though the sensitivity is lower, because a compensated 100 mV per mT part tracks over temperature while an uncompensated 200 mV per mT part drifts.

Where 200 mV per mT earns its place

Triggers, pedals, joysticks, keyboard and instrument keys, and short travel throttle sensors are the applications. All of them have a small magnet, a small gap and a travel measured in millimetres, and all of them benefit from a signal that fills the converter range.

For programs that move between the compensated and uncompensated versions, the how to verify a drop in replacement page sets out the temperature test that separates them, and the excess inventory management page covers what to do with a reel of the wrong letter after a change.

Questions we get on this code

Is 20 mT of range enough? For a neodymium disc at 1 to 3 mm it is usually more than enough, and the risk is the opposite, a magnet that is too strong and clips the output at half travel. Measure the field at the working gap before choosing between Z1 and A2.

Why does this part cost the same as the compensated one? Because the die is the same and only the trim differs; the compensation is a curve in the same memory, not a second circuit. That also means the two parts behave identically at 25 C, which is why a temperature test is the only way to tell them apart on a bench.

The last point is the offset. With 200 mV per mT of gain, the 130 mV spread of the quiescent window is only 0.65 mT of apparent field, which is small in field terms and large in counts. A start up calibration removes it and is worth the few lines of code.

The last consideration is the magnetic circuit itself. At 200 mV per mT the part is reading a field that changes by milliteslas over a millimetre, so the mechanical tolerance on the gap is directly a gain error. A shim of 0.2 mm in the magnet pocket moves the reading more than the sensor tolerance does, and the calibration fixture has to hold the gap as tightly as the production part.