AD2428WCCSZ-RL
Product Specifications
AD2428WCCSZ-RL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD2428WCCSZ-RL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD2428WCCSZ-RL: The A2B Transceiver That Carries Audio and Power on One Pair
The AD2428WCCSZ-RL is an Automotive Audio Bus transceiver that can be configured as the main node or as a subordinate node, and carries up to 32 channels in each direction of digital audio, clock and control over a single differential twisted pair. It exists because a car now has more microphones and speakers than a wiring harness wants to support. Buyers reach this page when a cabin audio or active noise cancellation harness has to lose weight and the analogue cabling is the constraint.
What the part contains
A configurable A2B node with an I2S or TDM interface from 8 to 32 bits, up to 32 upstream and 32 downstream channels, and a pulse density modulation interface for four digital microphones direct into the transceiver, with simultaneous reception of I2S data and the four PDM channels. The control port is I2C at the main node, and the same protocol is embedded in the A2B stream, so a host can reach registers and status on every subordinate node and run I2C to I2C across the cable. Each transceiver carries a unique ID register, which is how a host enumerates the chain after power up. Cabling can be straight through or crossover, the EMC settings are programmable, and the main node can supply bus power to the subordinate nodes over the same pair. The part is AEC-Q100 qualified and is listed by the vendor as recommended for new builds.
Key parameters
| Parameter | Value |
|---|---|
| Role | Main node or subordinate node, configurable |
| Cable | Single differential twisted pair, line topology |
| Distance between nodes | Up to 15 m |
| Total cable length | Up to 40 m |
| Channels | Up to 32 upstream and 32 downstream |
| Audio interface | I2S or TDM, 8 bit to 32 bit |
| Microphone interface | Up to 4 PDM inputs |
| Control | I2C at the main node, embedded in the bus stream |
| Power | Bus power from the main node, or local power at a node |
| Qualification | AEC-Q100 |
| Package | 40-lead LFCSP |
What the numbers mean on a board
Thirty two channels of 32 bit audio at 48 kHz is 49.152 Mbit/s in each direction. That is the arithmetic behind the frame structure: the bus has to carry a fixed superframe at that rate whether the channels are used or not, so a node that needs four microphones still occupies its slot in the frame. Planning the channel map before the harness is built is cheaper than discovering after the build that a new microphone needs a channel that has already been allocated.
Fifteen metres between nodes and 40 m in total sets the cable specification. The propagation delay of a twisted pair is roughly 5 ns per metre, so 15 m is 75 ns of one way delay before any node processing. That number is small compared with an audio sample period of 20.8 microseconds, which is why the bus can keep every node phase aligned to the same clock; it is also why the daisy chain order matters, because every node in front of a given node adds its own fixed delay to the stream.
Bus power is the feature that removes copper. The main node sends current down the same pair that carries the data, and the drop along the cable is what limits how many nodes can be powered that way. A node with a 200 mA load at the far end of 15 m of thin cable sees both the conductor resistance and the connector resistance, and the voltage at the node has to stay above its own regulator's dropout. Nodes with a real power demand should be locally powered, which the part allows per node.
Where it is used
- Cabin audio distribution with a reduced harness
- Active noise cancellation with microphones on the same bus as the speakers
- Hands free and in car communication microphone arrays
- Industrial and medical equipment that distributes audio or sensor channels along a machine
- Any system where a single pair has to replace several analogue runs
Sourcing notes and next step
The suffix on this order code is the automotive grade and the packing, so the W is the qualified part and the RL is the reel. The part is configured in software, which means the same silicon serves as main or subordinate, and a board that was built for one role can be re used in the other after a configuration change. The trap in a production build is firmware and silicon revision pairing: keep the configuration file under revision control with the reel label, because a node that enumerates but does not pass audio is almost always a configuration mismatch rather than a dead transceiver.
Automotive interface parts that carry a long production commitment are collected on the obsolete and long life hub, and matched transceiver and connector sets for a harness build are in BOM shortage recovery. The rest of the catalogue is on the analog and mixed signal family page. Send the node count, the channel map and the quantity and we confirm stock and date code the same day.
Request Quote — In Stock, 100% New & Original, Full Warranty