Contact Us

DRV2510QPWPRQ1

Brand: Texas Instruments
Texas Instruments DRV2510QPWPRQ1 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV2510QPWPRQ1 — Power Management & Signal Chain | Superb Automation

DRV2510QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV2510QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV2510QPWPRQ1: the automotive haptic driver in the 16 pin HTSSOP

The DRV2510QPWPRQ1 is a three amp peak haptic driver for solenoids and voice coils in a 16 pin HTSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE, qualified to AEC-Q100 temperature grade 1 at minus 40 to plus 125 degrees, and lists an operating voltage of 4.5 to 18 V, integrated load dump protection to 40 V per ISO 7637-2, a full H-bridge output with 3 A peak current, low on resistance, integrated diagnostics and fault reporting, an analogue input, an I2C interface and a dedicated interrupt pin.

This is the part in this batch that a customer is most likely to find through a search for a function rather than a part number. A haptic driver replaces a mechanical button in a centre console or a steering wheel, and the choice is driven by the actuator, the supply and the diagnostic requirement rather than by the driver alone. The datasheet is written from the actuator backwards, which is why the load impedance row matters as much as the current rating.

The DRV2510QPWPRQ1 rows as the addendum publishes them

Part classAutomotive haptic driver, full H-bridge, for solenoids and voice coils
Vendor statusACTIVE, production data
Data sheetSLOS919D, June 2016, revised November 2023
QualificationAEC-Q100, temperature grade 1
Operating voltage4.5 V to 18 V
Peak output current3 A
On resistance, pin to pin180 milliohms at 25 degrees junction
Load dump protection40 V per ISO 7637-2
Minimum load impedance1.5 ohm
Quiescent current16 mA active, 7 mA standby, 5 to 20 microamps shut down
Regulator output6.4 V minimum, 6.9 typical, 7.4 maximum
Gain options20, 26, 32 and 36 decibels
Output offset25 millivolts maximum, gain 20 decibels
Supply rejection75 decibels at 12 V with 1 Vrms at 1 kHz
Common mode rejection63 decibels at 1 kHz
Input common mode range0.3 V to 4.4 V
Oscillator frequency400 kHz typical
InterfaceI2C, 7 bit address given as 0x6C in the interface section
ProtectionUndervoltage lockout, overcurrent, overtemperature, overvoltage
Thermal, junction to ambient39.4 degrees per watt, 16 pin HTSSOP
BodyHTSSOP, 16 pins, 5.00 by 4.40 millimetres
Reel rowDRV2510QPWPRQ1, 2000 pieces, large tape and reel
MarkingDRV2510 on the body
Moisture levelLevel 3 at 260 degrees, 168 hour floor life

The address row is worth a note. The interface section of the document gives the seven bit slave address as 0x6C, and a later section of the same document prints a different seven bit address with its eight bit equivalents. Only one of those can be right for this device, and the difference matters at bring up because a controller that writes to the wrong address gets no acknowledge and no movement. We state the interface section figure on this page and recommend confirming the address against a vendor support note or a bench check before a production image is frozen.

What the electrical table fixes

The 3 A peak against a 1.5 ohm minimum load is the pair that defines the actuator. At 3 A into 1.5 ohms the voltage across the load is 4.5 V, which is the bottom of the supply range, so a 4.5 V rail with a 1.5 ohm actuator is the worst case the part is specified for. A lower impedance actuator draws more current than the bridge will deliver and the output limits, which shows up as a weak click rather than as a fault.

The on resistance of 180 milliohms pin to pin at 25 degrees is measured through the package and the bond wires, and it is the number to use in a dissipation sum. At 2 A the bridge drops 0.36 V and dissipates 0.72 W, which with 39.4 degrees per watt is 28 degrees of rise. A haptic pulse is short, so the average is much lower, but a repeated pulse train at 50 per cent duty is where the thermal calculation starts to matter.

The regulator output of 6.9 V typical is an internal rail for the analogue blocks, and it is brought out on a pin, so a board can use it or load it. The gain options of 20, 26, 32 and 36 decibels are set by register, not by external resistors, which means the actuator level can be changed in software without a board change and the same board can serve two actuators. That is why the part is popular in platforms where the mechanical package arrives after the electronics.

Where the body fits on a board

The 16 pin HTSSOP measures 5.00 by 4.40 millimetres and carries a thermal pad, which is the path for the pulse energy. The load dump protection means the supply pin does not need an external clamp for the ISO pulse, which saves a transient suppressor and the board area around it. The interrupt pin is the diagnostic path, and a board that leaves it unconnected has the protection but not the reporting.

The moisture level 3 rating gives a 168 hour floor life, and an automotive module line that runs a reel over several days should track the exposure. The part is qualified to grade 1, which is minus 40 to plus 125 degrees ambient, and the package is a plastic HTSSOP, so the qualification is about the die and the assembly rather than about a ceramic body.

What the documents do not publish

The page gives no curve of output current against actuator impedance, only the 3 A peak and the 1.5 ohm minimum load. It gives no acoustic or mechanical response data, which is reasonable for a driver but means the actuator choice cannot be made from the driver document. It also does not give a settling or rise time for the output, so the shape of the click has to be measured.

The address discrepancy noted above is the one documentation gap that has a direct effect on a production image. A second gap is the diagnostic register map, which is in the document but not on the product page, and a customer who wants to read a fault code has to open section seven for the bit definitions. Neither gap is unusual in an automotive part and both are worth knowing before a first article.

Second source and long term availability

Automotive haptic drivers are made by a small number of vendors and the register model differs between them, so a cross is a software change at minimum. The grade and the load dump capability are the two features to match first. The pin to pin cross reference page sets out the comparison, and the defence grade components page covers the screening question that sits next to automotive grade in some programmes.

The part is in its fourth revision and the addendum carries a single 2000 piece reel row, which is a narrow supply base. A programme with a long life should ask the vendor for a written availability statement and should not assume that a second source will appear, because the automotive qualification cost keeps the field small.

What to send with an enquiry

Send the exact string, the packing, the quantity and the date. State the actuator impedance and the drive voltage, because the 1.5 ohm minimum load is the boundary of the specification. State whether the interrupt pin is used and whether the application needs the diagnostic readback.

Say which gain setting the software expects, since the gain is a register value and a change is free at the board and not free in the validation plan. A repeated pulse train at high duty is the case the 3 A peak does not cover. The BOM scrubbing page explains how we reconcile a line like this against a build quantity before a schedule is confirmed.