Contact Us

CD4504BPWR

Brand: Texas Instruments
Texas Instruments CD4504BPWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4504BPWR — Power Management & Signal Chain | Superb Automation

CD4504BPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4504BPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4504BPWR: the hex voltage level shifter on a 2000 piece TSSOP reel

The CD4504BPWR is the thin shrink small outline reel entry for the CD4504B, six level shifting circuits that translate an input signal from the VCC logic level to the VDD logic level, in a 16-lead body. The vendor page lists the device as ACTIVE with six bits, a data rate of 24 Mbps, a fixed direction, an input range of 5 to 18 V, an output range of 5 to 18 V, a propagation delay of 280 ns and a maximum supply current of 5 mA. The reel row is 2000 pieces with a nickel palladium gold finish, and the marking is CM504B.

The part exists because a board with two rails needs a defined interface between them. The vendor states that VCC can exceed VDD, that input signals can exceed both rails, and that the SELECT input chooses between a TTL threshold and a CMOS threshold. That combination means the shifter can sit between a 5 V logic section and a 12 V section without a direction pin, a clock or a supply sequence, which is the reason it is still specified on industrial boards that have no room for a modern translator.

The CD4504B rows as the addendum publishes them

Part classSix channel level shifter, fixed direction
Vendor descriptorHex voltage level shifter, 6 bits
Vendor statusACTIVE, catalogue rating
Data sheetSCHS097 or later revision, acquired from Harris Semiconductor
Package addendum date18 September 2026
Input range5 V to 18 V
Output range5 V to 18 V
Data rate24 Mbps in the parametric table
Propagation delay280 ns
Supply current5 mA maximum
Supply sequencingVCC may exceed VDD, inputs may exceed both rails
Threshold selectSELECT high for TTL input, low for CMOS to CMOS
Input current1 microamp at 18 V over temperature, 100 nA at 25 degrees
TSSOP body16 leads, 32 square millimetres, 5 by 6.4 mm
TSSOP tube rowCD4504BPW, 90 pieces, Active
TSSOP reel rowCD4504BPWR, 2000 pieces, Active
SOIC tube rowsCD4504BM, 40 pieces, Active
SOIC reel rowCD4504BM96, 2500 pieces, Active
SOIC small reelCD4504BMT, 250 pieces, Active
PDIP rowCD4504BE, 25 pieces in a tube, Active
Ceramic rowsCD4504BF3A, 25 pieces, Active
Body areasPDIP 181.42, SOIC 59.4 and TSSOP 32 square millimetres

Every row is live, and the family offers three pack sizes in the SOIC body alone. That is unusual in this band and it makes the part easy to buy at any volume. The TSSOP offers a 90 piece tube and a 2000 piece reel, so a pilot build can use the tube and the production run can move to the reel without a footprint change. The plastic DIP is the option for a socketed board and for a repair kit.

What the parametric table fixes

The 280 ns propagation delay is slow by the standards of a modern translator and it is the number that decides where this part can be used. A 24 Mbps data rate and a 280 ns delay do not describe the same edge: the data rate is a family entry and the delay is what a signal actually sees. A board that passes a 1 MHz clock through the shifter loses a quarter of a period to the delay, and a board that passes a 10 MHz clock loses two and a half periods, which is a phase shift rather than a delay.

The supply current of 5 mA maximum is the highest in this group of devices and it is the price of six level shifting stages. The input current at 18 V is 1 microamp, so the driving stage sees a light load, and the input range extends above both rails, which is what allows a 12 V signal to drive a part whose VDD is 5 V. The SELECT input sets the input threshold to either TTL or CMOS, and the vendor describes the TTL position as the one to use when the driving signal comes from a bipolar logic family.

The output range is the same as the input range, 5 to 18 V, and the shift is always from VCC to VDD rather than in either direction. A board that needs a bidirectional interface has to use two parts or a different device, and the page states the fixed direction in the parametric table rather than leaving it to a note.

Where the TSSOP body fits

At 32 square millimetres the TSSOP is the smallest body in the family, less than a fifth of the plastic DIP area and about half of the SOIC. The 0.65 mm pitch is the trade: it needs a finer stencil and a closer optical check than the 1.27 mm SOIC, and on a board with a wide ground pour the solder bridging risk rises. A line that already places fine pitch parts takes the TSSOP without a process change, and a line that does not should take the SOIC.

The 2000 piece reel and the 90 piece tube cover both ends of the volume range. For a board that uses two shifters, a single reel covers a thousand boards, and the tube covers forty five boards for a pilot. The marking CM504B is shorter than the orderable string, which is normal for a 16-lead TSSOP and is the first thing a first article inspection compares against the drawing.

The SELECT input is the pin most often miswired. With SELECT high the input threshold is the TTL one, which is what a 5 V bipolar driver needs, and with SELECT low the threshold is the CMOS one, which is what a CMOS driver at the same rail needs. A board that ties SELECT to the wrong rail still works on the bench with a clean signal and fails in the field with a slow one, because the threshold sits at the wrong fraction of the rail. The vendor prints the two positions in the feature list, and the page repeats them because the pin is easy to overlook.

The six channels are independent and share only the two rails and the select line. That means one channel can shift a 5 V signal to 12 V while another shifts a 12 V signal to 5 V, as long as the two rails are wired the right way round for each. A board that needs both directions on the same rail pair needs two packages, one wired each way.

What the documents do not publish

No output current rating, no channel to channel skew and no maximum frequency at temperature appear on the page. The data sheet carries the switching table and the test circuit. The page also does not print the pin out, and for a level shifter the pin out is the specification, because the input side and the output side are on opposite rails and a reversed connection is a fault rather than a performance loss.

Second source and long term availability

The CD4504B is second sourced under the same number and every body is active, so a near term shortage is unlikely. A modern alternative is a wide supply translator in a smaller package, and the substitution changes the threshold behaviour and the propagation delay in ways that matter to a slow bus. The how to verify a drop in replacement page sets out the checks, and the incoming inspection plan page covers what to test on the first delivery of a new source.

What to send with an enquiry

Send the string, the body, both rail voltages, the signal frequency and the quantity. The two rails decide whether the part can be used at all, and the frequency decides whether the 280 ns delay is acceptable. If the board is surface mount, say whether the line can place a 0.65 mm pitch, because the TSSOP and the SOIC are both live and the choice is a process decision. The BOM consolidation page explains how the pack sizes are grouped before a quote is issued.