Contact Us

CC110LRGPR

Brand: Texas Instruments
Texas Instruments CC110LRGPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CC110LRGPR — Power Management & Signal Chain | Superb Automation

CC110LRGPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CC110LRGPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CC110LRGPR sub 1 GHz value line transceiver in the 20 pin 4 by 4 mm QFN body

The CC110LRGPR is the value line member of the CC1101 radio family, a single chip transceiver for the 300 to 348 MHz, 387 to 464 MHz and 779 to 928 MHz bands. The radio core, the sensitivity and the output power behaviour are the same as the CC1101, and the difference sits in the digital side and the price. Two of these devices plus a microcontroller and a handful of passives make a bidirectional link, which is why the part keeps appearing in remote controls, alarm sensors and metering nodes that run for years on one cell.

The reason a value line part exists at all is that most short range products do not need the full feature set of the flagship radio. They need a receiver that hears a weak packet at 1.2 kBaud, a transmitter that reaches 10 dBm, a sleep current low enough to survive a shelf life, and an SPI port the host can drive. The CC110L keeps those four and trims around them. The frequency synthesiser is fully on chip, so there is no external filter and no external RF switch, and the bill of materials around the radio is small enough that the passives do not decide the cost of the board.

Key parameters taken from the CC110LRGPR document

Frequency bands300 to 348 MHz, 387 to 464 MHz and 779 to 928 MHz, with 392 MHz as the practical floor in the middle band when a 27 MHz crystal is used
Modulation2-FSK, 4-FSK, GFSK, MSK and OOK, all selectable from registers
Data rate0.6 to 600 kBaud in 2-FSK, 0.6 to 250 kBaud in GFSK and OOK, 0.6 to 300 kBaud in 4-FSK
Output powerProgrammable up to +12 dBm, with +10 dBm as the usual production setting and a PATABLE of eight power steps
SensitivityMinus 116 dBm at 0.6 kbps, minus 118 dBm at 1.2 kBaud on 868 MHz and minus 120 dBm at 1.2 kBaud on 915 MHz, all at one per cent packet error rate
Supply1.8 to 3.6 V on all supply pins, which have to sit at the same potential
TemperatureMinus 40 to plus 85 C ambient
Sleep current200 nA typical, 1 microamp maximum, with the digital regulator off and the register content retained
Wake up time240 microseconds from sleep to receive or transmit
Receive current15.4 mA at 1.2 kBaud on 315 MHz, 15.7 mA on 868 and 915 MHz, both with register settings trimmed for reduced current
Transmit current34.2 mA at +12 dBm on 868 MHz, 30.0 mA at +10 dBm, 16.8 mA at 0 dBm, 16.4 mA at minus 6 dBm, and 33.4 mA at +11 dBm on 915 MHz against 30.7 mA at +10 dBm
Buffer64 byte receive and 64 byte transmit FIFO, with sync word insertion, flexible packet length and automatic CRC in hardware
Range extensionPairs with the CC1190 front end for +20 dBm at 868 MHz and +26 dBm at 915 MHz
BodyQFN 20 pins, 4 by 4 mm, 0.5 mm pitch
Order code factsCC110LRGPR, QFN RGP 20 pins, 3000 pieces on a large reel, NIPDAU finish, moisture level 3 with a 168 hour floor life, marking CC110L; the T suffix is the same body on a 250 piece small reel

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The current table is the one that decides battery life, and it has to be read with its conditions attached. The 15.4 mA receive figure belongs to 1.2 kBaud on 315 MHz with the demodulator filter offset enabled, which trades a little sensitivity for a little current. Run the same part at 250 kBaud and the receive current climbs to 16.5 mA, and switching the filter offset off costs another fraction. On a duty cycled sensor the average current is dominated by sleep and wake, not by receive, so the 200 nA sleep figure and the 240 microsecond wake are the two numbers worth protecting in the firmware.

The transmit side is where the power budget is spent unevenly. At plus 12 dBm the part draws 34.2 mA on 868 MHz, at 0 dBm it draws 16.8 mA, and the four decibels between 0 and 12 cost more than double the current. On a product that transmits a short packet once a minute, that difference is invisible in the average. On a product that repeats every second, it decides the cell size. The same applies to the external front end: with the CC1190 the output reaches 26 dBm at 915 MHz, but the current is drawn from the same rail, so the boost has to be paid for somewhere.

Sensitivity numbers move with data rate in a way that catches people out. The minus 116 dBm headline belongs to 0.6 kbps, and the part gets about four decibels worse as the rate climbs to 250 kBaud. A link budget built on the headline figure and then run at 38.4 kBaud will look healthy on paper and marginal in the field, because the antenna, the matching network tolerance and the body loss around a handheld product all eat into the same margin. Build the budget at the rate the product actually uses.

The middle band has a trap worth knowing. With a 27 MHz crystal the lower limit of the 387 to 464 MHz band becomes 392 MHz, so a 390 MHz channel is outside the guaranteed range even though the band table appears to include it. Customers who need that region either move the crystal or accept the part outside its published window, and we would rather say so before a reel is bought than after a prototype fails compliance.

  • Sleep current measured on the assembled board, not on the bare part, since a leaking regulator or a pull up on the SPI bus hides the 200 nA.
  • Wake to receive time in the actual firmware, because the 240 microseconds is a silicon figure and the interrupt path can add to it.
  • Receive current at the data rate the product ships with, not at the rate used in the first bench test.
  • Transmit current at the selected PATABLE step, with a current probe on the rail rather than a bench supply reading.
  • Output power at the antenna connector after the matching network, on three boards, since the matching tolerance moves the delivered power by a decibel or more.
  • Crystal start up and frequency accuracy over temperature, which decides whether the channel spacing holds at the band edges.

Which projects this part fits

This part fits wireless alarm and security sensors, remote controls and key fobs, home and building automation nodes, industrial monitoring where a cable cannot be run, wireless metering in the 433 and 868 MHz bands, and any product that has to meet EN 300 220 in Europe or FCC Part 15 in the United States. It is also the usual starting point for a proprietary protocol at low data rate, because the packet handler and the FIFOs remove most of the firmware work that a raw radio would need. Customers building a long range link at 915 MHz with an external front end use the same part and add the range extender, which keeps the host firmware unchanged.

Questions that come up before a purchase order is released

Can the CC110L replace a CC1101 without a board change?

Only if the firmware is reworked. The two share the radio core and the RF performance, but the register set and the interface of the value line part are reduced, so a binary built for the CC1101 does not run on the CC110L. The pins and the body match, which makes the swap mechanically simple and electrically safe, but the host code has to be ported and retested at the packet level.

What antenna matching is needed at 868 MHz?

A balun and a low pass filter between the differential RF pins and the single ended antenna, with the values taken from the vendor reference for the band and the board thickness. The part needs no external RF switch, and the matching network is the only RF work on the board. On a 4 layer board with a ground plane under the radio, the reference network usually lands within a decibel without tuning, and on a two layer board it rarely does.

How does the part behave at 1.8 V?

The whole radio runs from 1.8 V, and the output power falls a little compared with 3.0 V because the power amplifier has less headroom. The receive current also falls. A product that runs from a lithium cell through most of its life will see the delivered power drop as the cell discharges, and the link budget has to be built at the bottom of the supply window rather than at the nominal 3.0 V.

Is the 64 byte FIFO enough for a sensor packet?

It is enough for a payload of a few dozen bytes with a header and a CRC, which covers most sensor and command traffic. A product that needs to move a firmware image or a log file has to stream through the FIFO in bursts, and the host has to service the radio faster than the FIFO fills. The packet handler helps, but the throughput is set by the SPI clock and the host interrupt latency, not by the radio.

What is checked at incoming inspection?

The reel label against the order, the moisture barrier bag and its humidity indicator, the marking on a sample of parts, and a functional check on a test board that transmits a known packet and receives it back. The radio has no way to be checked with a multimeter, so the test board is the practical instrument. We keep the test firmware with the lot record so a later failure can be compared against the accepted baseline.

How SUPERB handles this line

We supply the CC110LRGPR from original reels with lot and date code traceability, and we hold the reel size on the order because the large reel and the small reel carry the same part in the same body. The RF component sourcing page lists the sub 1 GHz radio families we carry together with the front end parts that pair with them, obsolete RF part replacement covers the case where a radio in an existing product goes end of life, and pin to pin cross reference is the page to start from when a board has to take a different radio without a respin.