CC0402KRX7R8BB104
Product Specifications
CC0402KRX7R8BB104
Texas Instruments — Power Management & Signal Chain
Product Overview
The CC0402KRX7R8BB104 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CC0402KRX7R8BB104: 0402 X7R 100 nanofarad 25 V multilayer ceramic capacitor
CC0402KRX7R8BB104 is a general purpose multilayer ceramic chip capacitor in a 0402 body of 2 pins. The part is a 100 nanofarad X7R chip capacitor in an 0402 case, rated 25 VDC at 10 percent tolerance, 0.5 mm thick, rated from minus 55 to plus 125 degrees Celsius and supplied in 10000 piece reels.
Order code and package
| Order code | CC0402KRX7R8BB104 |
| Case | 0402, 1005 metric, 1.0 by 0.5 by 0.5 mm |
| Capacitance | 100 nanofarad |
| Tolerance | plus or minus 10 percent |
| Rated voltage | 25 VDC |
| Dielectric | X7R |
| Temperature range | minus 55 to plus 125 degrees Celsius |
| Termination | tin, halogen free, RoHS |
| Moisture level | MSL 1 |
| Reel quantity | 10000 pieces |
Electrical parameters that decide the application
| Dissipation factor | 5 percent maximum |
| Insulation resistance | 5 gigohm minimum |
| Endurance test voltage | 200 percent of rated voltage |
| Style | SMD chip |
| Leakage at 25 V | 5 nA from the insulation resistance |
| Temperature coefficient | X7R, plus or minus 15 percent over the range |
Points to check before this part goes on a BOM
Five gigohms at 25 V is 5 nA of leakage, which is 64 times lower than the 1 microfarad X5R part in the same case. On a hold-up rail or a battery backed clock node the leakage of the decoupling bank is part of the standby budget, and this is the part that keeps that term small.
The dissipation factor is 5 percent, which for 100 nanofarad is 79.6 ohms at 1 kHz and a small fraction of an ohm in the megahertz range. That is the shape of a bypass capacitor: it is there for the high frequency current loop and not for bulk storage, and the 1 microfarad part in the same case is the one for the lower band.
X7R holds its rating to 125 degrees, 40 degrees above the X5R dielectric in the same case size. A product that has to survive a soak test at 105 degrees, or sit next to a regulator, needs the 125 degree part even when the capacitance and the case are identical.
The endurance test runs at 200 percent of rated voltage, which is 50 V here. That is a qualification stress, not a working voltage, and a rail that swings to 30 V on a hot plug event is outside the 25 V rating no matter what the endurance line says.
The plus or minus 10 percent tolerance is the room temperature figure before the dielectric tolerance of X7R, which is another plus or minus 15 percent over the temperature range, and before the loss at the working voltage. A capacitor specified as 100 nanofarad can be 70 nanofarad at 25 V and 125 degrees, so a timing or filter value that depends on it has to be checked at the extremes rather than at the nominal.
The same 0402 land pattern carries the 1 microfarad 16 V X5R part of this series. A line that substitutes by position can put the lower temperature, lower voltage, higher leakage part where the X7R was specified, and nothing in incoming inspection will catch it unless the marking or the reel is checked.
Tin termination and MSL 1 mean a standard reflow profile with no bake, which keeps the passive line simple. Parts that have been stored in a humid environment still need the check if the reel seal is broken, and the reel quantity of 10000 is the practical unit for that decision.
25 V is the right rating for a 12 V or 24 V industrial rail with margin. On a 24 V rail at plus 10 percent the part sits at 26.4 V, above its rating, so a 50 V part is the answer for a 24 V system and the 25 V part belongs on the 12 V side of the converter.
The same order string logic applies here: 104 is 100 nanofarad, the 8 is the 25 V voltage code, and the X7R block is the dielectric. The 16 V version of the same value carries a 7 in that position, so the voltage code is one character and the difference between a 16 V and a 25 V part is invisible without reading it.
A hundred nanofarad in an 0402 X7R is the workhorse bypass value on almost every digital rail, which means substitution pressure is constant. The parts that get offered as equivalents differ in dielectric, in voltage code or in termination, and only the last of those shows up as a solderability problem rather than as a field failure.
X7R is a class 2 dielectric, so the capacitance moves with voltage, temperature and time. The 5 percent dissipation factor and the 15 percent temperature coefficient describe a part that is meant for bypass and coupling, not for a filter whose corner frequency has to hold over temperature; an NP0 part is the answer for that and it is a different order code entirely.
Where this order code fits
High frequency decoupling on 3.3 V and 12 V rails, filter and timing networks, and any position where the ambient goes above 85 degrees or the leakage has to stay in the nanoamp range. Teams comparing it with a neighbouring part start from our Incoming Inspection Plan page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Is 25 V enough for a 24 V rail? Not with tolerance. A 24 V rail at plus 10 percent is 26.4 V, above the rating, so the 50 V part in the same series is the correct choice for that rail and the 25 V part belongs on rails up to about 18 V.
How does it compare with the 1 microfarad part in the same case? It has 64 times less leakage and a 40 degree wider temperature range, at one tenth of the capacitance. Which one belongs on a board depends on whether the position needs bulk charge or a high frequency path.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.