Contact Us

BQ7721611PWR

Brand: Texas Instruments
Texas Instruments BQ7721611PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ7721611PWR — Power Management & Signal Chain | Superb Automation

BQ7721611PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ7721611PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ7721611PWR: the 200 mV hysteresis option for a 16 series pack

The BQ7721611PWR is a member of the same 3 to 16 series protector family, with a four second overvoltage delay, a 6 V active high output and a different balance of settings from the 09 option. The 11 option uses 200 mV of undervoltage hysteresis and switches the open wire check off.

Those two changes look small on a comparison table and they decide very different builds. Doubling the undervoltage hysteresis keeps a pack from chattering at the end of discharge on a load that pulses, which is what a motor drive does when the operator holds the trigger at low speed. Turning off the open wire check removes a continuous current from every sense line and removes the constraint that the series resistors stay low enough for the check to work.

The part is still a full protector: overvoltage, undervoltage, and with a thermistor on the board, overtemperature and undertemperature. The voltage comparators hold plus or minus 10 mV at room and plus or minus 20 mV from 0 to 60 C.

Key data for the BQ7721611PWR

FunctionVoltage and temperature protection for a lithium ion pack
Cell count3 to 16 cells in series
Overvoltage range3.55 V to 5.10 V across the family options
Undervoltage range1.0 V to 3.5 V across the family options
AccuracyPlus or minus 10 mV at 25 C, plus or minus 20 mV from 0 to 60 C
Overvoltage delay4 seconds
Undervoltage hysteresis200 mV
Open wire checkDisabled on this option
Overtemperature75 C charge cutoff with an external NTC thermistor
Output driveActive high, drives to 6 V
Supply currentAbout 1 microamp with all cells below the protection point
Package24 pin TSSOP, 4.40 mm by 7.80 mm body
TemperatureMinus 40 to 110 C operating, 2000 pieces per reel

Why hysteresis decides whether a pack stutters at the end of discharge

At the end of a discharge the pack voltage sags under load and recovers when the load is removed. A protector with a small hysteresis releases the output, the load reconnects, the voltage sags again, and the cycle repeats several times a second. The user hears a tool that stutters, or sees a display that flickers, and the pack is blamed.

With 200 mV of hysteresis, the voltage has to recover 200 mV above the undervoltage threshold before the output releases. On a pack with a cell impedance of 20 milliohms and a load of 20 amps, the sag across the string is a few hundred millivolts, so the larger hysteresis absorbs it and the pack stays off until the load is actually removed.

The same number has a cost at the other end. A deep undervoltage that recovers slowly will keep the pack off for longer, and a user who expects the pack to come back after a rest will find that it does not. That is a product decision, not a part decision, and it belongs in the specification of the end equipment.

What switching off the open wire check buys, and what it costs

With the check off, the part no longer injects current into the sense lines, so the series resistors in front of each input can be larger. That is useful on a sixteen cell stack where the sense harness runs a metre and picks up noise, because a 1 kilo ohm resistor and a capacitor to the local ground make a filter that a smaller resistor cannot.

The trade is that a broken sense wire now reads as a plausible voltage. On a stack with a break above the midpoint, the sum of the cells below the break appears at the input of the upper comparator, which either reads low, and never trips, or reads high, and trips without a real fault. A pack that loses a sense wire and stops charging for no visible reason is usually this failure.

The mitigation is at the harness, not at the part: a keyed connector that cannot be half inserted, a service check that measures each sense line against the pack, and a monitor that cross checks the sum of the cells against the pack voltage. If those exist, the check inside the protector is redundant. If they do not, the 09 option is the safer choice.

Where it fits in a build

The 11 option suits packs that drive a motor with a pulsing load and that have a monitor which already checks the sense harness: light electric vehicles, cordless tools, cleaning equipment. It is not a fit for a pack that has no monitor and no harness check, because the open wire fault then has no other detector.

The part is ordered in reels of 2000 with a nickel palladium gold finish, and it is a repeat item for the life of the pack programme. For a build that carries several protection parts across pack variants, the kitting service page covers how the parts for one release are grouped and checked as a set.

The sourcing side of this part is covered on the supplier scorecard. For an automotive adjacent part that has to be available for the life of the pack, that page covers how a source is scored over a programme.

Questions we get on this code

Can the hysteresis be changed on the board? No, it is set by the option. A different hysteresis means a different part number, which also changes the open wire behaviour, so the two settings cannot be traded independently.

Is a four second overvoltage delay too slow? It is a compromise. A cell that is being overcharged rises slowly, and four seconds of delay avoids nuisance trips from transients on a charger cable. A cell that is already at the limit is being pushed by tens of milliamps at that point, so four seconds adds very little charge.

Does the part balance the cells? No. There is no bleed path inside it. Balancing belongs to the monitor or to a separate bleed network, and the protector only decides when the pack must stop.

What replaces this part if it is not available? The other options in the same family share the package and the pinout, but the thresholds and the hysteresis differ. A drop in substitution needs the option table read line by line, because two parts can differ only in the undervoltage point.