INA2126EA250
Product Specifications
INA2126EA250
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA2126EA250 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA2126EA250: the wider grade, and the row that drops to moisture level three
INA2126EA250 is the EA grade of the two channel part, 250 pieces on a small reel in the 16 pin SSOP. The electrical rows are the family's, 175 microamps per channel, 250 microvolts maximum of offset, 3 microvolts per degree of drift and a gain of 5 to 10 000, and the difference from the E grade is the handling column rather than the electrical table.
The addendum prints this row at moisture level 3 with a 168 hour floor life, while the E grade beside it prints level 2 with a one year floor life. A line that opens the bag on Monday and builds on Friday is unaffected; a line that opens a reel and returns to it three weeks later needs a bake, and the plan has to say so. The catalogue code drops the separator entirely, so the string on a purchase order is not the vendor string, and a buyer who types the vendor form into a catalogue search may not find the row at all.
INA2126EA250 as the vendor document publishes it
| Channels | 2 |
| Quiescent current | 175 microamps per channel |
| Supply range | 1.35 volts to 18 volts |
| Offset voltage | 250 microvolts maximum |
| Offset drift | 3 microvolts per degree maximum |
| Common mode rejection | 80 dB minimum, 94 dB typical |
| Power supply rejection | quoted in microvolts per volt from 1.35 to 18 volts |
| Input bias current | 25 nanoamps maximum |
| Voltage noise | 35 nanovolts per root hertz |
| Gain | 5 to 10 000 V/V, one external resistor per channel |
| Temperature range | minus 40 to plus 85 degrees |
| Body | SSOP, 16 pin, DBQ |
| Vendor status | active, 250 piece small reel |
| Catalogue code | INA2126EA250 |
| Vendor string | INA2126EA/250, printed with a slash |
| Grade | EA, moisture level 3 |
| Lead finish | printed as a call to the vendor on this row |
| Moisture level | level 3, 168 hour floor life |
Eighty decibels of rejection, and the input window that goes with it
The common mode rejection of INA2126EA250 is 80 dB minimum and 94 dB typical, and the power supply rejection is quoted in microvolts per volt over the 1.35 to 18 volt range. The two op amp architecture puts the input window inside the rails rather than at them.
Eighty decibels turns a 1 volt common mode into 100 microvolts at the input, which is under the 250 microvolt offset, so the two error terms are balanced and neither dominates. The window is the limit that matters more: a ground referenced sensor on a single 1.35 volt rail has almost no headroom, and a bridge that sits at half rail is the natural application. A high side shunt on a 12 volt bus is outside the window on any supply the part can take, and so is a sensor whose common mode sits at the positive rail. The window is also the row that improves with the supply: on 18 volts the part has the headroom a plus or minus 10 volt signal needs, and on 1.35 volts almost all of the range is taken by the amplifier's own operating point.
A hundred and seventy five microamps per channel
INA2126EA250 is a two channel instrumentation amplifier that draws 175 microamps per channel, so a dual package costs 350 microamps for two independent front ends. The supply range of 1.35 to 18 volts is the widest in this group and covers a single alkaline cell as well as a 15 volt industrial rail.
The two op amp architecture is what makes the current draw possible. It is not a three op amp instrumentation amplifier, so the input stage has a common mode range that stops short of the rails and the rejection is lower, and in exchange the part runs from 1.35 volts and draws a fraction of what a three op amp part needs. For a portable instrument with two sensors and a coin cell budget, that trade is the whole reason the part exists, and it is also why the part turns up in a four to 20 milliamp transmitter that has to take its supply from the loop current: 350 microamps for two channels leaves the converter and the reference room to work.
Thirty five nanovolts and twenty five nanoamps
The voltage noise of INA2126EA250 is 35 nanovolts per root hertz and the bias current is 25 nanoamps maximum, which pairs the part with sources of a few kilo-ohms. On a 350 ohm bridge the source noise is 1.7 nanovolts and the amplifier dominates; on a 100 kilo-ohm source 25 nanoamps of bias current gives 2.5 millivolts of offset, ten times the published maximum.
That is the arithmetic a two op amp front end forces on the board: the bias current is the price of the low supply current, and a high impedance sensor needs either a lower bias part or a buffer ahead of it. For a bridge, an RTD or a thermopile the 25 nanoamps are harmless, and the 35 nanovolts are quiet enough that a 16 bit converter is limited by its own reference rather than by the front end.
Two hundred and fifty microvolts, three microvolts per degree
The offset of INA2126EA250 is 250 microvolts maximum with a drift of 3 microvolts per degree maximum, and the bias current is 25 nanoamps maximum. The temperature range is minus 40 to plus 85 degrees, which is narrower than the rest of this group and is the first row to check on an industrial application.
The 3 microvolts per degree is the row that matters over that window: 125 degrees of range gives 375 microvolts of drift, larger than the maximum offset itself. A channel that calibrates at room temperature and runs at 85 degrees therefore has about 600 microvolts of total offset, which on a 10 millivolt bridge is six per cent. On a 200 millivolt span it is a third of a per cent, and there the part is the cheapest way to get two channels of differential amplification.
Two channels in one package, and where that fits
INA2126EA250 belongs in a portable two channel instrument, a level or flow transmitter with a temperature compensation channel, a patient monitor with two differential inputs, an infusion pump with a pressure and a force channel, and any board where 350 microamps for two front ends is the difference between a coin cell and a battery pack.
It stops at three things. The temperature range ends at plus 85 degrees, so an industrial module that runs hot needs a different part. The common mode window sits inside the rails, so a high side sensor needs a divider or a different front end. And the 250 microvolt offset belongs to a large signal channel rather than to a load cell, where a chopper part is the answer. Our amplifier cross reference page covers the single channel member of the family, and the vendor consolidation page covers buying the two channels and the single on one line.
Gain from five to ten thousand on one resistor
The gain of INA2126EA250 is set by a single resistor from 5 to 10 000, with the internal network trimmed at a gain of 5 in the same way as the single channel part. Two channels share the package but not the gain resistor: each channel brings out its own pins, so a dual can run two different gains.
That is convenient for a two sensor instrument, and it is also a trap for a bill of materials: the two resistors are separate components with separate tolerances, so a dual used at two gains has two gain errors rather than one. A production build that needs matching channels is better served by two resistors from the same reel and the same tolerance band, or by a part with a fixed gain on both channels.
The grade here is a handling grade, so the receiving inspection is where the decision lands. Our traceability report page covers the label and the certificate, and the BOM scrubbing page covers the code against the bill of materials.
Is the EA grade electrically different? The electrical table is shared with the E grade; the printed difference is the moisture level, 3 against 2.
What is the floor life? 168 hours at level 3, against one year at level 2. Beyond that a bake is required before reflow.