Contact Us
  • Home
  • COMPONENTS
  • Steel and Aluminium DIN Rails for Control Cabinets

Steel and Aluminium DIN Rails for Control Cabinets

NS 35/7,5 and NS 35/15 rail in steel and aluminium, 2 m lengths. Perforated and unperforated profiles to EN 60715. Short time current 1.92 kA for 1 s on the 7.5 mm steel profile. End caps and end stops quoted with the rail, cut to panel width on request.
quote now

Product Specifications

Product Overview

A DIN rail looks like a strip of bent steel until the panel is loaded. The profile sets what fits on it, the thickness sets how much a terminal strip can pull before the rail bows, and the material decides whether the rail can be used as a protective conductor path or only as a mechanical support.

Two profiles cover most panels. NS 35/7,5 is 35 mm wide and 7.5 mm deep with 1 mm steel, and takes the majority of terminal blocks, relays and small power supplies. NS 35/15 is the same 35 mm width and 15 mm deep with 1.5 mm steel, for deeper devices and for runs that carry more weight. Both are tested to EN 60715.

Material matters at the ends. Galvanised steel is the default and carries a short time current of 1.92 kA for 1 s with an equivalent copper cross section of 16 mm2, which is what makes the rail usable as a bonding path when the panel is built that way. Aluminium is lighter and does not rust, but it is not a conductor path and needs a separate earth bar.

Key Specifications

PropertyNS 35/7,5NS 35/15
Width35 mm35 mm
Depth7,5 mm15 mm
Material thickness1 mm1.5 mm
StandardEN 60715Similar to EN 60715
Steel versionGalvanised, thick layer passivatedGalvanised, thick layer passivated
Aluminium versionOn requestUncoated, 35 x 15 mm
Length2000 mm2000 mm
Short time current, steel1.92 kA for 1 sBy profile and fixing
Equivalent copper cross section16 mm2By profile and fixing

Included Models and Order Codes

Order codes below are Phoenix Contact. The 7.5 mm profile is the one that matches the UT and UK terminal families; the 15 mm profile is for deeper devices and for rails that carry a heavier strip.

Part numberProfileMaterialPerforationLength
0801681NS 35/7,5Steel, galvanisedUnperforated2000 mm
0801733NS 35/7,5Steel, galvanisedPerforated2000 mm
1201714NS 35/15Steel, galvanisedUnperforated2000 mm
1201756NS 35/15Aluminium, uncoatedUnperforated2000 mm
1206573NS 35/15 end capPlastic--
0800886E/NS 35 N end stopPolyamide-48.6 mm

Key Features

Two profiles, one width – 35 mm devices fit both the 7.5 mm and the 15 mm profile, so a deeper rail does not change the terminal choice.

Steel as a bonding path – the 7.5 mm steel profile carries 1.92 kA for 1 s with a 16 mm2 copper equivalent, which supports its use as a protective conductor path.

Perforated for fast fixing – the perforated version takes self tapping screws on a 25 mm pitch, which shortens the drilling on a long run.

Aluminium for weight – the 35 x 15 mm aluminium profile is for door mounted rails and for panels where total weight is a transport limit.

End caps and stops together – the plastic end cap closes the cut end and the end stop holds the strip, both quoted with the rail.

Cut to panel width – rails are supplied in 2 m lengths and can be cut to the panel schedule, with the cut list checked before dispatch.

Applications

Rail is bought with the strip layout. Three patterns repeat.

Control and automation panels – 7.5 mm steel rail for UT terminal strips and relay bases, fixed on a 25 mm pitch.

Power distribution – 15 mm steel rail for deeper devices and for runs carrying a heavier terminal strip.

Door and swing frame – 15 mm aluminium rail where the door weight is limited and the rail does not have to carry a bonding current.

Rails are quoted by the metre with the terminals and the stops, and the SUPERB PCBA and the SUPERB PCB are checked against the same rail schedule so the cut list is fixed before the panel is drilled.

Sourcing and Cross-Reference

Work out the load per rail, not per panel. A 2 m run of UT 6 terminals with 10 mm2 wires pulls far more than the same length of UT 2,5, and the 15 mm profile is the answer before a second support bracket is.

Say whether the rail is a bonding path. If it is, the steel profile has to be used with the correct fixing and the paint has to be removed at the contact points; an aluminium rail needs a separate earth bar.

Cut ends need a cap. A bare cut edge catches wires and leaves a sharp corner inside the panel; the end cap is a one line addition to the order.

Rails and stops are quoted with the terminals, and a short length for a repair can come from the same batch. See lead time and availability for cut lengths and mixed orders.

The SUPERB Assembly team cuts and deburrs the rail before the strip is laid out, since a burr changes the pitch at the end of the run.

Q: Can the rail be supplied cut to the panel width?

A: Yes. Send the panel width and the rail profile; the SUPERB Tech team quotes the cut lengths, the end caps and the stops as one line.

Why Panel Builders Buy DIN Rail From SUPERB

  1. Profile and material stated: the quote names the profile, the thickness and the material, so the rail is not substituted by a lighter section.
  2. Rail, caps and stops in one order: the cut end is closed and the strip is held with parts from the same delivery.
  3. Steel and aluminium side by side: bonding runs and weight limited doors are quoted from the same source.
  4. Batch traceable: the rail batch is recorded with the panel, which keeps the material record complete for audit builds.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: DIN Rail End Stops and Partition Plates, DIN Rail Terminal Blocks, Mounting Brackets and DIN Rail Clips, Busbars and Earth Bars.