Ring Terminals and Spade Connectors for Panel Wiring
Product Specifications
Product Overview
A ring terminal closes around a stud, so the joint cannot pull off the way a fork can. It is the terminal for a connection that is expected to stay for the life of the panel: an earth bond, a battery feed, a chassis return, a breaker lug. The part is simple, a copper barrel, a tongue with a hole, and an insulation sleeve on the insulated versions, and almost every field failure comes back to two dimensions.
The first is the stud hole. A number 6 stud takes a 0.147 in terminal hole, a number 8 takes 0.173 in, a number 10 takes 0.204 in, a 1/4 in stud takes 0.270 in, a 5/16 in stud takes 0.343 in and a 3/8 in stud takes 0.392 in. Those are the Panduit bolt hole figures, and they are larger than the stud because the terminal has to sit flat under a washer without the plating riding up the thread. Order a number 8 terminal for a number 10 stud and the hole is too small; order a number 10 for a number 8 stud and the contact area drops.
The second is the wire barrel. A 22-18 AWG part, 16-14 part and 12-10 part have three different barrel bores, and the insulation sleeve colour follows the range: red for 22-18, blue for 16-14 and yellow for 12-10 on the Panduit parts. The colour is a code, not a decoration, and it matches the die station in the crimp tool. A blue terminal crimped in a red station is a joint that passes a pull test on a bench and fails in a panel.
The PN range on this page is nylon insulated and covers all three wire ranges. PN10-8R is the 12-10 part for a number 8 stud: 0.040 in stock, 0.370 in tongue width, 1.060 in overall, with maximum wire insulation diameter of 0.225 in. PN10-6R and PN10-10R share the same 1.060 in length on a 0.038 in tongue, and PN10-14R grows to 1.21 in long and 0.52 in wide for a 1/4 in stud, with a 0.38 in maximum insulation diameter. On the 16-14 range, PN14-8R is 0.86 in long and 0.31 in wide with a maximum insulation diameter of 0.25 in, and PN14-14R is 1.06 in and 0.44 in for the 1/4 in stud.
The P range is the bare copper version of the same terminals, tin plated, without a sleeve. A bare ring is the right part inside a cabinet where the joint is enclosed and the clearance is tight, and it is the wrong part on a wire that flexes, because the strands at the barrel mouth have nothing to support them. Where a bare terminal is used, a length of heat shrink over the barrel restores the strain relief.
The PV range is the vinyl insulated family, rated to 105 C with a V-2 or HB sleeve depending on the part, and it costs less than nylon. Nylon brings V-0 with it, so the choice between the two is usually made by a flame test rather than by price. On a panel that has to pass a glow wire or a vertical burn, the nylon part is the one that is written into the drawing.
Fork and locking fork terminals do a different job. A fork slides under a screw that is loosened rather than removed, which saves time on a terminal block or a busbar that carries twenty wires. The locking fork has a tongue that closes over the stud so it does not slip out when the screw is slackened, and it is the version to specify where a technician may work on the panel live. PV14-6LF and PN14-6LF are the 16-14 locking forks for a number 6 stud, PV18-6LF and PN18-6LF the 22-18 versions, and PV10-8F the 12-10 fork for a number 8 stud.
Crimp tooling is part of the terminal, not an accessory. The Panduit range runs on the CT-100 plier tool for the small sizes, and on the controlled cycle CT-400 and CT-460 tools where a repeatable crimp height has to be recorded, with the die station matched to the sleeve colour. The tool has to be set for the terminal family, and a terminal from one family crimped with another family die is the most common reason a ring pulls off.
Key Specifications
| Parameter | Value | Notes |
|---|---|---|
| Wire ranges | 22-18, 16-14 and 12-10 AWG | Bare P range extends to 22-16 and 14-10 |
| Stud sizes | Number 6, 8, 10, 1/4 in, 5/16 in, 3/8 in | Number 4 on some 22-18 parts |
| Terminal hole diameter | 0.147 in on number 6 to 0.392 in on 3/8 in | Larger than the stud for washer clearance |
| Insulation | Bare, vinyl, nylon | Vinyl 105 C, nylon V-0 |
| Sleeve colour code | Red 22-18, blue 16-14, yellow 12-10 | Matches the crimp die station |
| Terminal material | Copper | Electro tin plated |
| Stock thickness | 0.038 in to 0.040 in on the 12-10 parts | Stated per part |
| Rating | 600 V on the insulated ring terminals | Per UL 486A for the family |
| Crimp tooling | CT-100 plier, CT-400 and CT-460 controlled cycle | Die station per sleeve colour |
| Fork types | Fork and locking fork | Locking fork closes over the stud |
Included Models and Order Codes
Ring terminals are listed by wire range and stud size, with the length, the tongue width and the maximum insulation diameter that the barrel will accept. The fork and locking fork parts follow, because a stud that is loosened rather than removed takes a different terminal.
| Part Number | Wire Range | Stud Size | Insulation | Length | Tongue Width |
|---|---|---|---|---|---|
| PN18-6R | 22-18 AWG | Number 6 | Nylon, red | 0.79 in | 0.31 in |
| PN18-8R | 22-18 AWG | Number 8 | Nylon, red | 0.79 in | 0.31 in |
| PN18-10R | 22-18 AWG | Number 10 | Nylon, red | 0.86 in | 0.31 in |
| PN18-14R | 22-18 AWG | 1/4 in | Nylon, red | 1.06 in | 0.44 in |
| PN14-6R | 16-14 AWG | Number 6 | Nylon, blue | 0.86 in | 0.31 in |
| PN14-8R | 16-14 AWG | Number 8 | Nylon, blue | 0.86 in | 0.31 in |
| PN14-10R | 16-14 AWG | Number 10 | Nylon, blue | 0.86 in | 0.31 in |
| PN14-14R | 16-14 AWG | 1/4 in | Nylon, blue | 1.06 in | 0.44 in |
| PN10-6R | 12-10 AWG | Number 6 | Nylon, yellow | 1.06 in | 0.38 in |
| PN10-8R | 12-10 AWG | Number 8 | Nylon, yellow | 1.06 in | 0.37 in |
| PN10-10R | 12-10 AWG | Number 10 | Nylon, yellow | 1.06 in | 0.38 in |
| PN10-14R | 12-10 AWG | 1/4 in | Nylon, yellow | 1.21 in | 0.52 in |
| PN10-56R | 12-10 AWG | 5/16 in | Nylon, yellow | 1.21 in | 0.52 in |
| PN10-38R | 12-10 AWG | 3/8 in | Nylon, yellow | 1.29 in | 0.58 in |
| P18-8R | 22-16 AWG | Number 8 | Bare, tin plated | 0.79 in | 0.31 in |
| P14-6R | 18-14 AWG | Number 6 | Bare, tin plated | 0.86 in | 0.31 in |
| P10-8R | 14-10 AWG | Number 8 | Bare, tin plated | 1.06 in | 0.38 in |
| PV18-6LF | 22-18 AWG | Number 6 | Vinyl locking fork | Per part | Per part |
| PN18-6LF | 22-18 AWG | Number 6 | Nylon locking fork | Per part | Per part |
| PV14-6LF | 16-14 AWG | Number 6 | Vinyl locking fork | Per part | Per part |
| PN14-6LF | 16-14 AWG | Number 6 | Nylon locking fork | Per part | Per part |
| PN14-8F | 16-14 AWG | Number 8 | Nylon fork | Per part | Per part |
| PV10-8F | 12-10 AWG | Number 8 | Vinyl fork | Per part | Per part |
| P10-10F | 14-10 AWG | Number 10 | Bare fork | Per part | Per part |
Key Features
Hole diameter matched to the stud – 0.147 in to 0.392 in across the range, so the tongue sits flat under a washer instead of riding up the thread.
Three wire ranges in one family – 22-18 in red, 16-14 in blue and 12-10 in yellow, with the barrel bore changing with each range.
Bare, vinyl and nylon versions – The same tongue in three insulations, so a flame test decides the part rather than a stock list.
Locking fork for a loosened stud – The tongue closes over the stud so the terminal does not slip out when the screw is backed off.
Diminishing stock thickness stated – 0.040 in on the 12-10 ring, 0.038 in on the number 6 and 10 versions, which is what the torque figure depends on.
Tooling and die station named – CT-100, CT-400 and CT-460 with the die matched to the sleeve colour, so the crimp is repeatable.
Tin plated copper throughout – A copper barrel with electro tin plating, which keeps the joint solderable and slows corrosion at the stud.
Applications
Ring terminals go on earth bonds, battery and breaker feeds, chassis returns and transformer lugs, where the joint is made once and checked at every service.
Panel earth and bonding – A 12-10 ring on a 1/4 in stud at the chassis earth point, with a star washer and a torque figure written on the drawing.
Power entry and breaker lugs – 0.040 in stock on the 12-10 part, on a number 8 or number 10 stud, in a cabinet where the terminal is inspected annually.
Sensor and signal returns – 22-18 nylon rings on number 6 studs, where the sleeve has to stay on the wire through a vibration sweep.
Terminal blocks and busbars – Locking forks on 16-14 wire so a technician can loosen one screw without the terminal dropping behind the rail.
A ring terminal is chosen by the stud it goes over and the wire it takes, and the two numbers pull in opposite directions, so the SUPERB PCB wiring schedule is read with the stud size beside the wire gauge. On the SUPERB PCBA route the terminals are crimped to the loom before the board is fitted, so the stud hardware can be torqued without pulling a soldered joint.
Sourcing and Cross-Reference
Two numbers decide a ring terminal and they are both on the drawing: the stud and the wire gauge. When only the wire is given, the answer is a family rather than a part, and the hole diameter still has to be agreed before the order is placed. We quote the part number with the hole, the tongue width and the maximum insulation diameter so the fit can be checked on paper.
For a joint that is re-terminated in the field, the terminal has to match the tool that the technician carries. A nylon insulated part needs its own die station, and a bare part crimped in an insulated die is not a substitute. We list the tool with the terminal because the pair is what passes the pull test, not the terminal on its own.
Where a part is obsolete, the substitute is chosen on hole diameter, wire range and insulation rating together. A number 8 and a number 10 ring look interchangeable on a bench, and a number 10 part on a number 8 stud loses contact area. We check all three before we quote a replacement.
SUPERB Assembly pulls the first terminal of a build to its rated load on a tension gauge and cuts a sample open, because a ring that is crimped outside the wire barrel looks closed and still pulls off at a fraction of the rated force.
Q: Can you supply 12-10 nylon insulated ring terminals for a number 8 stud with the hole diameter confirmed, and the crimp die station that goes with them?
A: Send the wire gauge, the stud size, the stud material and the torque you intend to apply, and say whether the joint sits in a cabinet or outdoors. The SUPERB Tech desk quotes the ring with its hole diameter and its barrel, so the washer and the stud match the terminal.
Why Buy Terminals Through SUPERB
- Part quoted by hole and barrel: The stud hole and the wire barrel are confirmed together, which is where most cross referenced terminals go wrong.
- Three insulations in one place: Bare, vinyl and nylon rings and forks, so a flame test does not send the order to a second supplier.
- Tooling named with the part: The crimp tool and the die station are listed, so the joint can be repeated on the line and checked at inspection.
- Ratings stated per family: 600 V on the insulated rings and the temperature and flammability of each sleeve are given with the part number.
- Mixed quantities accepted: A service kit of twenty rings in three sizes is quoted as one line, not as three minimum orders.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Butt Splices and Crimp Connectors for Wire Joins, Wire Ferrules and Crimp Sleeves for Terminal Blocks, Grounding Studs and Earth Terminals for Chassis Wiring, Screw Terminal Blocks and Pluggable Connectors for Field Wiring, Banana Jacks and Binding Posts for Test and Bench Panels, Obsolete Part Cross Reference Hub.