Edge Trim and Grommet Strip for Panel Cut-outs
Product Specifications
Product Overview
A cut-out in a sheet metal panel has two sharp edges and one purpose: to let a cable, a hose or a finger through. Edge trim is the part that turns that opening into something a cable can rub against for ten years without a short, and something a fitter can put a hand into without a cut.
Three materials cover the work. Soft PVC is the cheapest and follows an irregular opening; polyethylene is stiffer and holds its shape on a long straight edge; TPE stays flexible at low temperature and grips a thicker sheet. The wall section, not the material name, decides which sheet thickness the strip will hold.
The strip is a press fit, so the sheet thickness has to be inside the range in the table. A 1.6 mm strip on a 2.5 mm plate will not close, and a 3.8 mm strip on a 1.0 mm plate sits loose and falls off at the first cable pull. Where the hole is irregular or the edge is on an inside curve, the adhesive lined type is the one that stays put.
Key Specifications
| Profile | Material | Sheet thickness | Wall height | Pack | Fixings |
|---|---|---|---|---|---|
| Grommet strip, plain | polyethylene | up to 0.9 mm | 3.2 mm | roll, cut to length | press fit |
| Grommet strip, rubber | TPE, black | up to 1.6 mm | 4.8 mm class | roll, cut to length | press fit |
| Edge trim, PVC | soft PVC, black | 1.0 to 3.7 mm | 2.0 to 5.2 mm | 50 m roll | press fit |
| Grommet edging, adhesive lined | polyethylene with adhesive | 1.57 to 2.51 mm | 4.8 mm | 100 ft coil | adhesive plus slotted wall |
Included Models and Order Codes
The codes below are the sections that are quoted most often. The panel thickness is the figure to match first: a strip that is one size too small will not close over the sheet, and one size too large will not grip it. All PVC sections are supplied in 50 m rolls and can be cut on site.
| Part number | Material | Sheet thickness | Wall height | Pack | Colour |
|---|---|---|---|---|---|
| PGS-1 | polyethylene | up to 0.9 mm | 3.2 mm | roll | natural |
| RG-1 | TPE | up to 1.6 mm | 4.8 mm class | roll | black |
| SR1050 | PVC | 1.0 mm | 2.0 mm | 50 m roll, 8 mm wide | black |
| 34075 | PVC | 1.5 mm | 2.8 mm | 50 m roll | black |
| 34076 | PVC | 2.7 mm | 3.8 mm | 50 m roll | black |
| 34077 | PVC | 3.7 mm | 5.2 mm | 50 m roll | black |
| GEE99F-A-C | polyethylene, adhesive lined | 1.57 to 2.51 mm | 4.8 mm | 100 ft coil | natural |
Matching the Profile to the Opening
Most returns come from a profile that was chosen for the material rather than for the shape of the opening. The table below is the short version of that decision.
| Opening | Profile | Why it holds |
|---|---|---|
| Long straight edge on a door or a gland plate | PVC section 34076 | stiff wall, stays on the sheet |
| Irregular hole, hand punched | GEE99F-A-C adhesive lined | adhesive holds where the edge is not straight |
| Round hole with a cable pulled through | RG-1 rubber strip | soft wall, follows the curve |
| Thin aluminium plate 0.8 mm | PGS-1 | narrow slot, grips without crushing the sheet |
| Cut-out in a painted panel | PVC 34077 | wide wall covers the paint edge |
Key Features
Four sheet ranges – 0.8, 1.0, 1.5, 2.7 and 3.7 mm sections, so the strip is matched to the plate rather than forced onto it.
Press fit, no adhesive – the plain and rubber strips clip on and stay on without a curing step, which matters when a panel is trimmed on site.
Adhesive lined option – the slotted wall with adhesive follows an irregular hole and an inside curve, where a press fit strip would lift.
50 m rolls – long enough for a batch of doors without a splice in the middle of a visible edge.
Soft PVC that does not stain – the section is non-staining and resists ozone, acids and sunlight, so a white enclosure stays white at the opening.
Cut with a knife – no tooling and no punching, so a cut-out that was changed at the last minute can still be trimmed before the panel is packed.
Applications
Edge trim is a small part with a large failure mode: a single missed edge is a chafed cable. Three places it is always worth fitting.
Cabinet door and gland plate cut-outs – a PVC section on every opening that a cable passes through, so the bundle does not saw against the plate each time the door swings.
Machine guards and access panels – a rubber strip on a hand opening and on a guard edge, to remove the cut risk without adding a folded lip.
Instrument and rack panels – a narrow polyethylene strip on a 1 mm aluminium front panel, where a wide PVC section would stand proud of the face.
Conduit, trim, plinth and interlock parts are quoted together with the panel they belong to, and the SUPERB PCBA and the SUPERB PCB are checked against the same enclosure schedule so the cut-outs, the threads and the door swing all agree before the cabinet is built.
Sourcing and Cross-Reference
Match the thickness before the colour. A strip listed for 1.5 mm sheet will close on 1.4 to 1.6 mm and will not close on 2.0 mm. If the plate is 2.0 mm and the drawing calls for a 1.5 mm strip, the drawing is the part that needs changing.
Measure the opening, not the cable. The strip covers the edge; the cable only decides how wide the opening has to be. A 22 mm hole for a 17 mm cable leaves enough room for the wall of the trim and the pull.
Order the roll length for the batch. A door with four openings uses about 3 m of trim; a 50 m roll covers a batch of panels and avoids a splice. Offcuts shorter than 300 mm are usually scrap.
Check the paint stage. Trim fitted before painting traps overspray and lifts at the corner; trim fitted after painting needs the paint edge to be clean. The usual order is paint, then trim, then cable. See lead time and availability when the trim and the plates have to ship together.
The SUPERB Assembly team fits the conduit and the edge trim after the plates are painted, because a trim strip fitted before painting lifts at the corner and a conduit run fixed before painting traps overspray inside the tube.
Q: Can you supply a sample length so we can check the fit on our sheet thickness?
A: Yes. Send the enclosure drawing or the cut-out list with the sheet thickness and the cable diameter; the SUPERB Tech team returns the conduit size, the fitting thread and the trim profile that fit the opening.
Why Builders Buy Edge Trim From SUPERB
- Thickness range stated per code: the sheet range is in the table, so the strip is chosen against the plate and not against a catalogue picture.
- Press fit and adhesive options: the plain strip for a clean straight edge, the adhesive type for an irregular hole.
- Rolls that match the batch: 50 m rolls and 100 ft coils, cut to length, so a small repair does not need a full pack.
- Trim quoted with the cut-out list: the profile is checked against the openings on the drawing before the order is confirmed.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Nylon Grommets and Hole Plugs, Cable Glands and Strain Relief Bushings, Viewing Windows and Display Bezels, Dust Caps and Connector Covers.