Contact Us

STM8S208S6T6C

Brand: ST
ST STM8S208S6T6C is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S208S6T6C — MCU & Embedded Processors | Superb Automation

STM8S208S6T6C

ST — MCU & Embedded Processors

Product Overview

The STM8S208S6T6C from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S208S6T6C: 32 Kbyte Flash STM8S MCU in LQFP44

STM8S208S6T6C is the 32 Kbyte Flash member of the STM8S 8-bit line in a LQFP44 body (10 by 10 mm), with 1536 bytes of true data EEPROM, 6 Kbyte of RAM, 34 general purpose I/O, 9 analog inputs and 15 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. The beCAN 2.0B active controller is part of this order code and runs at up to 1 Mbit/s.

Order code and memory

Order codeSTM8S208S6T6C
Program Flash32 Kbytes
Data EEPROM1536 bytes, 300 kcycle endurance
RAM6 Kbytes
PackageLQFP44, 10 by 10 mm
Pin count44
Maximum general purpose I/O34
External interrupt pins31
High sink outputs15
ADC channels9 of 16
Controller area networkbeCAN 2.0B active, 1 Mbit/s
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 9 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

This is the smallest CAN node in the family: 32 Kbytes of Flash, 1536 bytes of EEPROM, 6 Kbytes of RAM and the beCAN controller in a 44-pin 10 by 10 mm body with 34 I/O. The EEPROM is 512 bytes larger than the 207S6 with the same Flash and the same pin count.

Thirty two Kbytes has to hold the application plus the CAN driver, and the stack and buffers live in 6 Kbytes of RAM. A node that also runs a bootloader over CAN has to reserve both Flash sectors and RAM, and the reserved size should be fixed before the application is written, not after.

Nine analog channels, no reference pins and 8 CAPCOM channels apply here as on the rest of the 44-pin group. The CAN pins are shared with GPIO, so the transceiver standby and enable lines come out of the remaining I/O, and the 120 ohm termination is a board decision at each end of the bus.

Where this order code fits

Small CAN nodes in sensors, actuators, battery monitors and valve controllers, where the board is 10 by 10 mm and the application image fits in 32 Kbytes. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the MCU Cross Reference page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

What is the smallest CAN part in the line? This one, at 44 pins. The 48-pin 208C6 is the next step up, and the 32-pin bodies have no CAN member in this datasheet.

How much RAM does the CAN driver need? The controller has its own registers and the driver keeps one or two message buffers in RAM. On a 6 Kbyte part the honest budget is a few hundred bytes for the driver plus the stack, and the rest for the application.

What temperature range? Suffix 6 is minus 40 to plus 85 C. Above 105 C ambient the clock ceiling drops to 16 MHz, so a 24 MHz node is a 105 C and below part.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the BOM Shortage Recovery page walks through the checks that keep a substitute from failing on the bench.