Contact Us

STM8S208MBT6B

Brand: ST
ST STM8S208MBT6B is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S208MBT6B — MCU & Embedded Processors | Superb Automation

STM8S208MBT6B

ST — MCU & Embedded Processors

Product Overview

The STM8S208MBT6B from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S208MBT6B: 128 Kbyte Flash STM8S MCU in LQFP80

STM8S208MBT6B is the 128 Kbyte Flash member of the STM8S 8-bit line in a LQFP80 body (14 by 14 mm), with 2048 bytes of true data EEPROM, 6 Kbyte of RAM, 68 general purpose I/O, 16 analog inputs and 18 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. The beCAN 2.0B active controller is part of this order code and runs at up to 1 Mbit/s.

Order code and memory

Order codeSTM8S208MBT6B
Program Flash128 Kbytes
Data EEPROM2048 bytes, 300 kcycle endurance
RAM6 Kbytes
PackageLQFP80, 14 by 14 mm
Pin count80
Maximum general purpose I/O68
External interrupt pins37
High sink outputs18
ADC channels16
Controller area networkbeCAN 2.0B active, 1 Mbit/s
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 16 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

This is the largest member of the family: 128 Kbytes of Flash, 2048 bytes of EEPROM, 6 Kbytes of RAM, 68 I/O and the beCAN 2.0B active controller on the 80-pin body. It is the part for a CAN node that also needs a large program image, such as a gateway that translates between CAN and two serial protocols.

The 80-pin package brings out all 16 analog channels, both reference pins, 37 external interrupt inputs and 18 high sink outputs. RthJA is 38 C/W, so the 443 mW allowance at 85 C is far above the 11.4 mA typical run current at 24 MHz from 5 V.

The CAN controller adds a second clock domain requirement in practice: the bus timing is derived from the clock tree, so the crystal or the trimmed internal oscillator has to hold its tolerance across temperature for the chosen bit rate. At 1 Mbit/s the bit time is 1 microsecond, and a 0.5 percent clock error is 5 nanoseconds of the sample point per bit.

Where this order code fits

CAN gateways, multi axis motion controllers and vehicle or off highway control units that need 68 I/O, 16 analog inputs and a large program image on one device. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the MCU Cross Reference page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

How many CAN channels? One beCAN 2.0B active controller at up to 1 Mbit/s, with the receive and transmit pins shared with port GPIO.

What is the junction to ambient figure? 38 C/W for the LQFP80 at 14 by 14 mm, with 443 mW of allowed dissipation at 85 C ambient.

Is there a version without CAN? Yes, the STM8S207MB on the same body. The CAN pins become GPIO, so a board can carry both variants if the firmware differs.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the One Stop RF Supply page walks through the checks that keep a substitute from failing on the bench.