Contact Us

STM8S208C8T6

Brand: ST
ST STM8S208C8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S208C8T6 — MCU & Embedded Processors | Superb Automation

STM8S208C8T6

ST — MCU & Embedded Processors

Product Overview

The STM8S208C8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S208C8T6: 64 Kbyte Flash STM8S MCU in LQFP48

STM8S208C8T6 is the 64 Kbyte Flash member of the STM8S 8-bit line in a LQFP48 body (7 by 7 mm), with 2048 bytes of true data EEPROM, 6 Kbyte of RAM, 38 general purpose I/O, 10 analog inputs and 16 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. The beCAN 2.0B active controller is part of this order code and runs at up to 1 Mbit/s.

Order code and memory

Order codeSTM8S208C8T6
Program Flash64 Kbytes
Data EEPROM2048 bytes, 300 kcycle endurance
RAM6 Kbytes
PackageLQFP48, 7 by 7 mm
Pin count48
Maximum general purpose I/O38
External interrupt pins35
High sink outputs16
ADC channels10 of 16
Controller area networkbeCAN 2.0B active, 1 Mbit/s
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 10 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

The C8 in the 208 line is the 48-pin CAN node: 64 Kbytes of Flash, 2048 bytes of data EEPROM and 6 Kbytes of RAM, with the beCAN 2.0B active controller at up to 1 Mbit/s. The EEPROM is twice what the same pin count and Flash size gives in the 207 line, which matters when a node stores a configuration block and an event log alongside the application.

The 48-pin body has 10 of the 16 analog channels and no VREF pins, so the CAN node that also measures analog signals is working against VDDA as its reference. The controller itself needs an external transceiver and a 120 ohm termination at each end of the bus, and the pin pair is shared with GPIO, so the transceiver enable line has to come from one of the remaining 38 I/O.

CAN traffic does not stop the CPU from being the bottleneck: the part runs at 24 MHz with one wait state on Flash access under the WAITSTATE option bit, and zero wait states only to 16 MHz. At 1 Mbit/s a full standard frame occupies about 130 microseconds of bus time, which is well inside what this core can service at either clock.

Where this order code fits

CAN nodes in pumps, drives, battery systems and vehicle body controllers, where a 48-pin board has to carry the bus and a modest analog front end at the same time. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the MCU Cross Reference page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

Does the part include the transceiver? No. beCAN is the protocol controller only. A 5 V or 3.3 V CAN transceiver, its supply decoupling and the bus termination are external.

How much data EEPROM? 2048 bytes with a 300 kcycle endurance, twice the 1024 bytes of the 207C6.

Can I clock it at 24 MHz on a 3.3 V rail? Yes, with the WAITSTATE option bit set. Below 3.3 V the ADC clock falls back to 4 MHz and the analog timing changes, but the core clock is not limited by the supply in the 2.95 to 5.5 V range.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Obsolete Part Cross Reference Hub page walks through the checks that keep a substitute from failing on the bench.