STM8S207R8T6
Product Specifications
STM8S207R8T6
ST — MCU & Embedded Processors
Product Overview
The STM8S207R8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S207R8T6: 64 Kbyte Flash STM8S MCU in LQFP64
STM8S207R8T6 is the 64 Kbyte Flash member of the STM8S 8-bit line in a LQFP64 body (14 by 14 mm), with 1536 bytes of true data EEPROM, 6 Kbyte of RAM, 52 general purpose I/O, 16 analog inputs and 16 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.
Order code and memory
| Order code | STM8S207R8T6 |
| Program Flash | 64 Kbytes |
| Data EEPROM | 1536 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP64, 14 by 14 mm |
| Pin count | 64 |
| Maximum general purpose I/O | 52 |
| External interrupt pins | 36 |
| High sink outputs | 16 |
| ADC channels | 16 |
| Controller area network | not present |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 16 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
This is the 64 Kbyte member of the 64-pin group, with 52 I/O, 36 external interrupt pins, 16 high sink outputs and the full 16 channel ADC including the VREF pins. It is the natural step up from a 48-pin C8 when the analog count or the reference requirement forces a wider body.
The ADC clock limit is worth fixing before the board is routed: 4 MHz with VDDA between 3 and 5.5 V, 6 MHz only when VDDA is at 4.5 V or more, and 14 clock cycles per conversion. At 3.3 V that is 3.5 microseconds per channel, so a 16 channel scan at full speed takes about 56 microseconds plus sampling and setup.
With no CAN block, the 207R8 is a control and measurement part. A gateway that needs both CAN and 64 Kbytes on 64 pins goes to the STM8S208R8, which also carries 2048 bytes of EEPROM rather than 1536.
Where this order code fits
Multi axis control boards, instrument clusters and industrial I/O modules that need 16 analog inputs, a reference pin and 52 I/O on a 14 by 14 mm body. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
How long does a 16 channel scan take? At a 4 MHz ADC clock and 14 cycles per conversion, 3.5 microseconds each, so about 56 microseconds of conversion time for 16 channels before sampling and multiplexer settling are added.
Is the reference pin differential? Both VREF+ and VREF- are bonded on the 64 and 80-pin devices, so the converter can measure against a reference pair rather than the analog supply.
What replaces it if it goes obsolete? The 208R8 adds CAN on the same footprint. Outside ST, the nearest candidates are 8-bit parts with a different core and toolchain, so the firmware port is the real cost.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the OEM Procurement page walks through the checks that keep a substitute from failing on the bench.