STM8S207C8T6
Product Specifications
STM8S207C8T6
ST — MCU & Embedded Processors
Product Overview
The STM8S207C8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S207C8T6: 64 Kbyte Flash STM8S MCU in LQFP48
STM8S207C8T6 is the 64 Kbyte Flash member of the STM8S 8-bit line in a LQFP48 body (7 by 7 mm), with 1536 bytes of true data EEPROM, 6 Kbyte of RAM, 38 general purpose I/O, 10 analog inputs and 16 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.
Order code and memory
| Order code | STM8S207C8T6 |
| Program Flash | 64 Kbytes |
| Data EEPROM | 1536 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP48, 7 by 7 mm |
| Pin count | 48 |
| Maximum general purpose I/O | 38 |
| External interrupt pins | 35 |
| High sink outputs | 16 |
| ADC channels | 10 of 16 |
| Controller area network | not present |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 10 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
The step from C6 to C8 doubles the program array to 64 Kbytes and raises the data EEPROM from 1024 to 1536 bytes, which is not a linear rule: the 64 Kbyte 32-pin part keeps 1024 bytes, so EEPROM size has to be read from the order code table and not inferred from the Flash figure.
Current at 24 MHz is 11.0 mA typical with code executed from Flash at 3.3 V, 18 mA maximum, and 4.0 mA typical with the same code executed from RAM. That difference is the practical argument for moving the interrupt heavy inner loop into RAM on a part whose Flash is read with one wait state at 24 MHz.
The 48-pin body gives 38 I/O, 35 external interrupt pins and 16 high sink outputs, and it does not carry the VREF pins. If the analog front end needs a reference independent of the 3.3 V rail, this package cannot provide one, and the choice moves to the 64-pin R part or to an external reference on an ADC input.
Where this order code fits
Industrial gateways that need more program space than a 32 Kbyte part but must stay in a 7 by 7 mm body, plus appliance control boards where the 16 high sink outputs drive displays and relays without external drivers. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
Is the C8 a drop in for the C6? Pinout and package are the same, but the program array is twice the size and the EEPROM is 1536 instead of 1024 bytes. Code that reads the EEPROM size from a fixed address or assumes a 32 Kbyte boundary must be rebuilt.
What is the fastest ADC conversion at 3.3 V? The ADC clock is limited to 4 MHz when VDDA is between 3 and 5.5 V, and a conversion takes 14 clock cycles, so 3.5 microseconds. The 6 MHz ADC clock needs VDDA at 4.5 V or more.
What temperature grades exist? Suffix 6 is minus 40 to plus 85 C and suffix 3 is minus 40 to plus 125 C. The 24 MHz clock ceiling belongs to the 105 C and below range.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Component Lead Time Solutions page walks through the checks that keep a substitute from failing on the bench.