Contact Us

STM8S103K3T6C

Brand: ST
ST STM8S103K3T6C is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S103K3T6C — MCU & Embedded Processors | Superb Automation

STM8S103K3T6C

ST — MCU & Embedded Processors

Product Overview

The STM8S103K3T6C from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S103K3T6C: 8 Kbyte Flash STM8S MCU in LQFP32

STM8S103K3T6C is the 8 Kbyte Flash member of the STM8S 8-bit line in a LQFP32 body (7 by 7 mm), with 640 bytes of true data EEPROM, 1 Kbyte of RAM, 28 general purpose I/O, 4 analog inputs and 21 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.

Order code and memory

Order codeSTM8S103K3T6C
Program Flash8 Kbytes
Data EEPROM640 bytes, 300 kcycle endurance
RAM1 Kbytes
PackageLQFP32, 7 by 7 mm
Pin count32
Maximum general purpose I/O28
External interrupt pins27
High sink outputs21
ADC channels4 of 16
Controller area networknot present
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 4 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

The 103K3 is the low density part on a 32-pin LQFP: 8 Kbytes of Flash, 640 bytes of EEPROM and 1 Kbyte of RAM, with 28 I/O and a 16 MHz ceiling. The EEPROM has no read while write capability on this family, so a routine that logs data cannot execute from the same array while it writes.

With 1 Kbyte of RAM, the stack and the buffers share one small block. A UART receive buffer of 64 bytes, a 32 byte transmit buffer and a nesting depth of four interrupts is a realistic budget; anything that streams data has to do it with small buffers and interrupt driven handoff.

Eight Kbytes of Flash means the program is written for size: the 80 instruction core with 20 addressing modes helps, but a protocol stack plus a control loop plus a bootloader rarely fits. The 32-pin body offers 28 I/O, 21 high sink outputs and the same 2.95 to 5.5 V supply range as the rest of the family.

Where this order code fits

Very small sensor and relay boards, LED drivers and simple appliance timers where 8 Kbytes is enough and the BOM is the dominant constraint. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

What is the EEPROM size? 640 bytes, with the same 300 kcycle endurance as the rest of the family but no read while write capability, so code must not execute from the EEPROM array while it is being written.

Can it run at 16 MHz? Yes, at 16 MHz with zero wait states, drawing a few milliamps at 5 V. The internal 16 MHz RC oscillator is user trimmable, so no crystal is needed for a UART at moderate baud rates.

How many I/O on the 32-pin body? 28 I/O with 21 high sink outputs, which is more high sink capability than the larger 207 bodies offer because the low density part has fewer alternate functions per pin.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the How to Reduce Component Cost page walks through the checks that keep a substitute from failing on the bench.