Contact Us

STM8L151R8T6

Brand: ST
ST STM8L151R8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8L151R8T6 — MCU & Embedded Processors | Superb Automation

STM8L151R8T6

ST — MCU & Embedded Processors

Product Overview

The STM8L151R8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8L151R8T6: 64 Kbyte ultra-low-power STM8L MCU in LQFP64

STM8L151R8T6 is a 64 Kbyte Flash member of the STM8L ultra-low-power line in a LQFP64 body (10 by 10 mm), with 4 Kbytes of RAM, 2 Kbyte of data EEPROM, 54 general purpose I/O, 28 channels on the 12 bit converter and 2 channel of 12 bit DAC. The supply range is 1.65 to 3.6 V without brown out reset, 1.8 to 3.6 V with it and the core runs at up to 16 MHz. This order code has no LCD controller, so every port pin belongs to the application.

Order code and memory

Order codeSTM8L151R8T6
Program Flash64 Kbytes
Data EEPROM2 Kbyte with ECC and read while write
RAM4 Kbytes
PackageLQFP64, 10 by 10 mm
Pin count64
Maximum general purpose I/O54
ADC channels28 of the 12 bit converter
DAC channels2 of 12 bits with output buffer
LCD controllernot present on this order code
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage1.65 to 3.6 V without brown out reset, 1.8 to 3.6 V with it
Maximum CPU clock16 MHz, 16 MIPS peak
Run current200 uA per MHz plus 330 uA static
Halt current400 nA typical
Active halt1.4 uA typical with the real time clock running
Low power modes5.9 uA typical in low power run, 3 uA in low power wait
Wake up time4.7 microseconds from halt
Analog to digital converter12 bit, up to 1 Msps, 28 channels, internal reference voltage and temperature sensor on chip
Digital to analog converter2 channel of 12 bits with output buffer, 7 microseconds typical settling into 5 k and 50 pF
Comparators2, one fixed threshold and one rail to rail, both can wake the core
Timersthree 16 bit general purpose timers, one 16 bit advanced control timer with three channels, one 8 bit timer, beeper timer, window and independent watchdog
Serial interfacestwo SPI blocks, one I2C at 400 kHz, three USARTs with ISO 7816 and IrDA
DMA4 channels covering the ADC, both DAC channels, I2C, SPI1, SPI2, USART1 to USART3 and the five timers
Data EEPROM endurance300 kcycle with ECC and read while write
Program memory endurance10 kcycle, 30 years retention at 85 C
Identification96 bit unique ID, single wire interface module, USART bootloader

Points to check before this part goes on a BOM

The R8 is the 64 pin, 64 Kbyte member without the LCD controller, so all 54 port pins and 28 converter channels belong to the application. This is the part for a control board that needs a large pin count and a real analog front end but has no glass to drive: the two SPI blocks and three USARTs cover a radio, a host link and a service port at the same time, and the 4 Kbytes of RAM absorb the buffers that a 2 Kbyte part cannot.

Twenty eight channels on a 10 by 10 mm body means a board can measure three phase currents, a DC link, winding temperatures, an ambient sensor and a battery divider without a multiplexer, and still keep spare channels for factory calibration. The converter takes its reference from the VREF+ and VREF- pins rather than VDDA, and the datasheet gives separate accuracy tables for a 1.8 to 2.4 V reference and a 2.4 to 3.6 V reference, which is the first thing to check when a low voltage rail is used as the reference node.

On the power side the numbers are 200 uA per MHz plus 330 uA static in run mode, 5.9 uA in low power run, 3 uA in low power wait, 1.4 uA in active halt and 400 nA in halt, with a 4.7 microsecond wake up. With this many pins the leakage budget deserves attention: at 50 nA per floating I/O, 54 pins left in their reset state can dominate the halt current, so unused ports should be configured as outputs or pulled to a rail in firmware.

Where this order code fits

Motor and valve control boards, multi channel data loggers, portable analyzers and industrial remote I/O with 54 I/O and no display. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How is the R8 different from the R6? The R6 is the 32 Kbyte, 2 Kbyte RAM, 1 Kbyte EEPROM version in the same 64 pin body. The R8 doubles Flash to 64 Kbytes, RAM to 4 Kbytes and EEPROM to 2 Kbytes; pinout and peripherals are the same.

Can all 28 ADC channels be used together? They can be scanned in sequence, yes, with the 4 channel DMA moving results into RAM. The channels are multiplexed through one converter, so simultaneous sampling of all 28 is not possible and phase sensitive measurements need the sample timing planned.

What reference does the DAC use? The same VREF+ pin as the converter. Both 12 bit DAC channels have output buffers with a 7 microsecond typical settling time into 5 k and 50 pF.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.