STM32L476ZGT6
Product Specifications
STM32L476ZGT6
ST — MCU & Embedded Processors
Product Overview
The STM32L476ZGT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32L476ZGT6: 1024 Kbyte, LQFP144 body
STM32L476ZGT6 is a member of the STM32L476xx low power line with floating point described by DS10198 Rev 11. The order code fixes 1024 Kbytes of Flash, 128 Kbytes of SRAM, the LQFP144 body at 20 x 20 mm with 144 pins, 114 general purpose I/O and 24 analog channels, and the core runs at up to 80 MHz from a 1.71 to 3.6 V on VDD and 1.05 to 1.32 V on the VDD12 core rail supply.
Order code and memory
| Order code | STM32L476ZGT6 |
| Program Flash | 1024 Kbytes |
| SRAM | 128 Kbytes |
| Data EEPROM | not present on this line |
| Package | LQFP144, 20 x 20 mm, 144 pins |
| Maximum general purpose I/O | 114 |
| Analog input channels | 24 channels on the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| Segment LCD driver | 4x44 or 8x40 segments |
| Supply voltage | 1.71 to 3.6 V on VDD and 1.05 to 1.32 V on the VDD12 core rail |
| Maximum CPU clock | 80 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient |
| Datasheet | DS10198 Rev 11 |
Peripheral and electrical parameters
| Core | ARM Cortex-M4 with single precision floating point at up to 80 MHz, ART accelerator giving zero wait state execution from flash, 100 DMIPS and 273 CoreMark at 80 MHz, 106 ULPMark PP |
| Clock sources | 4 to 48 MHz crystal oscillator, 32 kHz crystal for the RTC, 16 MHz factory trimmed internal RC, internal 32 kHz RC, internal multispeed 100 kHz to 48 MHz oscillator auto trimmed by the 32 kHz crystal, and three PLLs for the system clock, USB and audio |
| Low power modes | 100 microamps per MHz in LDO mode, 39 microamps per MHz from 3.3 V with the external SMPS, 30 nanoamps in Shutdown, 120 nanoamps in Standby, 420 nanoamps in Standby with the RTC, 1.1 microamps in Stop 2 and 300 nanoamps on the VBAT domain |
| Timers | sixteen timers: two advanced control, two 32 bit and five 16 bit general purpose, two 16 bit basic, two low power timers that run in Stop, the two watchdogs and SysTick |
| Serial interfaces | three SPI blocks plus one Quad SPI, three I2C blocks at 1 Mbit/s with SMBus and PMBus, five USARTs, two UARTs, two SAI audio interfaces, one CAN 2.0B controller, USB OTG full speed, SDMMC and SWPMI |
| Analog | three 12 bit ADCs at 5 Msps with hardware oversampling to 16 bit, two 12 bit DAC channels, two operational amplifiers with programmable gain and two comparators |
| Memory interface | external memory interface for static memories, SRAM, PSRAM, NOR and NAND, with Quad SPI as a separate interface |
| Flash and EEPROM endurance | two flash banks with read while write on the 1 Mbyte codes, and 10 years of retention at 85 C quoted for the program memory |
| Thermal resistance junction to ambient | 32 C/W on LQFP144 |
| Input tolerance | most I/O 5 V tolerant, with up to 14 I/O on an independent supply down to 1.08 V |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC and the backup registers alive with the main rail off |
| Status | full production per the datasheet cover |
Points to check before this part goes on a BOM
The order code is Z for 144 pins, G for 1 Mbyte of Flash, T for the LQFP body and 6 for the industrial range. The 1 Mbyte flash is organised in two banks with read while write, which is what allows a firmware image to be received while the current one keeps running.
114 general purpose I/O is the largest count in the family and the reason this body exists: 24 analog channels, 48 pins of display, four serial buses and a memory interface do not fit any smaller package at the same time. 14 of those I/O sit on an independent supply down to 1.08 V.
The external memory interface addresses SRAM, PSRAM, NOR and NAND with separate address and data lines on this body, and the Quad SPI interface runs alongside it. A board that buffers a long acquisition in external PSRAM and boots from Quad SPI flash uses both and still has the internal 128 Kbytes of SRAM free for the signal chain.
The LQFP144 is rated 32 C/W junction to ambient, the best of the family, so 625 mW at an 85 C ambient against a 105 C junction. The larger body spreads the heat over more lead frame, which is the opposite of what most people expect from a bigger package.
Three 12 bit converters at 5 Msps, two 12 bit DAC channels, two operational amplifiers with programmable gain and two comparators are all present at once on this body, with 24 channels bonded out. A four channel analog front end with programmable gain and a comparator trip point fits inside the part.
Sixteen timers include two advanced control blocks for motor drive and two low power timers that keep counting in Stop. A product that drives a small motor, reads a display and logs to an SD card uses the advanced timers, the SDMMC interface and the display driver at the same time, which is what the pin count is for.
30 nanoamps in Shutdown, 120 nanoamps in Standby and 1.1 microamps in Stop 2 are the same figures as the smaller bodies, so the extra pins and memory cost nothing in the sleep states. 300 nanoamps on the VBAT domain keeps the RTC and the 32 backup registers alive from a coin cell.
The 144 pin body is also the only one in the family that carries the full external memory interface, so a product that needs external memory cannot be built in the 100 pin body without accepting bank 1 only. That constraint is a package decision made before the memory map exists.
Where this order code fits
It is the 1 Mbyte member in the 144 pin body with the full memory interface, used on portable analysers and medical instruments that need every peripheral the family carries. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the One Stop BOM Sourcing page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
How many analog channels does it expose? 24 on three 12 bit converters. The 100 pin body exposes 16, so a product with more than sixteen sensors has to take the 144 pin package or an external multiplexer.
Does it support external memory? Yes, with separate address and data lines for SRAM, PSRAM, NOR and NAND, plus a Quad SPI interface. The 100 pin body is limited to bank 1 of the interface and the 64 pin body has none.
Is 1 Mbyte the largest flash in the family? Yes, in two banks with read while write. The 512 Kbyte code has a single application image space and no read while write between banks at the same density.
What is the thermal advantage of the 144 pin body? 32 C/W junction to ambient against 45 in the 64 pin body, which is 625 mW against 444 mW at an 85 C ambient. The larger lead frame spreads the heat rather than concentrating it.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.