Contact Us

STM32L152VDT6

Brand: ST
ST STM32L152VDT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32L152VDT6 — MCU & Embedded Processors | Superb Automation

STM32L152VDT6

ST — MCU & Embedded Processors

Product Overview

The STM32L152VDT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32L152VDT6: 384 Kbyte, LQFP100 body

STM32L152VDT6 is a member of the STM32L151xD and STM32L152xD low power line described by DS8576 Rev 13. The order code fixes 384 Kbytes of Flash, 48 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 83 general purpose I/O and 25 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down supply.

Order code and memory

Order codeSTM32L152VDT6
Program Flash384 Kbytes
SRAM48 Kbytes
Data EEPROM12 Kbytes with ECC
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O83
Analog input channels25 channels on the 12 bit converter
Digital to analog converter2 channels of 12 bits
Segment LCD driver4x44 or 8x40 segments
Supply voltage1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down
Maximum CPU clock32 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient
DatasheetDS8576 Rev 13

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit
Clock sources1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC trimmed to plus or minus 1 percent, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC, and a PLL that also produces the 48 MHz USB clock
Low power modes230 microamps per MHz in Run mode with both flash banks active, 11 microamps in Low power run and 4.4 microamps in Stop with the RTC running
Timerseleven timers: one 32 bit timer, six 16 bit timers with up to four compare channels, two 16 bit basic timers and two watchdog timers
Serial interfaceseight SPI blocks of which two are I2S, two I2C blocks, five USARTs, one USB 2.0 device port and one SDIO interface
Analogone 12 bit ADC at 1 Msps, two 12 bit DAC channels, three operational amplifiers and two ultra low power comparators, with capacitance sensing on up to 33 channels
Memory interfacenot present on this body
Flash and EEPROM enduranceprogram memory rated 10 kcycles at 105 C with 300 kcycles typical, EEPROM 30 kcycles minimum, and retention of 30 years at 85 C against 10 years at 105 C
Thermal resistance junction to ambient43 C/W on LQFP100
Input tolerance5 V tolerant inputs on the general purpose ports, all mappable on 16 external interrupt vectors
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC and the backup registers alive with the main rail off
Statusfull production per the datasheet cover

Points to check before this part goes on a BOM

The order code is V for 100 pins, D for 384 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. The 152 prefix is the display part, so this code combines the largest density of the D document with the widest glass driver it offers.

The combination that matters here is 48 Kbytes of SRAM plus a 4x44 or 8x40 segment driver. A controller that holds a waveform table, a calibration set and a display map in RAM and drives 320 segments from the same chip does not need an external driver or a second microcontroller.

12 Kbytes of EEPROM with ECC is enough for a metering identity block, a calibration record and a rolling event log without an external serial EEPROM. That removes a part, a footprint and a bus from the board, which on a metering product is also a certification question rather than only a cost one.

The two flash banks support read while write, so a firmware update can be received while the application keeps the display and the metering running. On a product that must not lose the display during an update that is a requirement and not a convenience.

The LQFP100 is rated 43 C/W junction to ambient, which is 581 mW at an 85 C ambient against a 110 C junction. The display drive itself is microamps, so the thermal question is the backlight, the relay and the power stage around the part.

4.4 microamps with the RTC running and 11 microamps in Low power run are the two figures for a product that blanks the display at night and keeps the clock and the tariff table. The VBAT domain keeps the RTC and the backup registers alive with the main rail removed.

The memory interface is multiplexed only on this body, which saves pins for the 48 the glass takes. A board that needs a non multiplexed interface has to move to the 132 or 144 pin body, where the segment count is the same but the pin budget is not.

The 151 code in the same body has no driver and is otherwise identical. In a shortage the 151 will run the firmware but will not light the glass, so the substitution check has to look at the prefix before it looks at the memory.

Where this order code fits

It is the top of the display branch: 384 Kbytes, 48 Kbytes of SRAM and a full glass driver in a 100 pin body, used on panel controllers and metering products that show a lot and compute a lot. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the One Stop BOM Sourcing page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What is the largest display this part drives? 320 segments in the 8x40 arrangement, or 176 in the 4x44 arrangement. Both use 48 pins, so the choice is segment count against backplane count and viewing angle.

Can it run the display and a firmware update at the same time? Yes. The two flash banks support read while write, so the application keeps running from one bank while the new image is written to the other, and the display does not blank during the transfer.

Does it need an external EEPROM? Not usually. The 12 Kbytes of on chip EEPROM cover an identity block, calibration and an event log, so a serial EEPROM on the board is a choice rather than a requirement.

What is the difference from the 256 Kbyte version? STM32L152VCT6 in the xC document has 256 Kbytes of Flash, 32 Kbytes of SRAM, 8 Kbytes of EEPROM and a single flash bank. The pinout is the same, so the upgrade does not move the board.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.