Contact Us

STM32L152VCT6

Brand: ST
ST STM32L152VCT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32L152VCT6 — MCU & Embedded Processors | Superb Automation

STM32L152VCT6

ST — MCU & Embedded Processors

Product Overview

The STM32L152VCT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32L152VCT6: 256 Kbyte, LQFP100 body

STM32L152VCT6 is a member of the STM32L151xC and STM32L152xC low power line described by DocID022799 Rev 13. The order code fixes 256 Kbytes of Flash, 32 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 83 general purpose I/O and 25 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down supply.

Order code and memory

Order codeSTM32L152VCT6
Program Flash256 Kbytes
SRAM32 Kbytes
Data EEPROM8 Kbytes with ECC
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O83
Analog input channels25 channels on the 12 bit converter
Digital to analog converter2 channels of 12 bits
Segment LCD driver4x44 or 8x40 segments
Supply voltage1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down
Maximum CPU clock32 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient
DatasheetDocID022799 Rev 13

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit
Clock sources1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC trimmed to plus or minus 1 percent, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC, and a PLL that also produces the 48 MHz USB clock
Low power modes185 microamps per MHz in Run mode, 8.6 microamps in Low power run, 1.4 microamps in Stop with the RTC, 1.15 microamps in Standby with the RTC and 0.44 microamps in Stop with 16 wakeup lines armed
Timerseleven timers: one 32 bit timer, six 16 bit timers with up to four compare channels, two 16 bit basic timers and two watchdog timers
Serial interfacesup to eight SPI blocks of which two are I2S, two I2C blocks with SMBus and PMBus, three USARTs and one USB 2.0 device port; five of the eight SPI blocks are USARTs used in synchronous mode
Analogone 12 bit ADC at 1 Msps, two 12 bit DAC channels, two operational amplifiers and two ultra low power comparators, with capacitance sensing on up to 23 channels
Memory interfacenot present on this body
Flash and EEPROM enduranceprogram memory rated 10 kcycles at 105 C, EEPROM cycling stated separately in the same table, and retention given as 30 years at 85 C against 10 years at 105 C
Thermal resistance junction to ambient43 C/W on LQFP100
Input tolerance70 of the 83 I/O on the 100 pin body are 5 V tolerant, all mappable on 16 external interrupt vectors
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC and the backup registers alive with the main rail off
Statusfull production per the datasheet cover

Points to check before this part goes on a BOM

The order code is V for 100 pins, C for 256 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. The 152 prefix carries the display driver and the step-up converter that keeps the glass contrast stable as the supply falls.

83 general purpose I/O out of 100 pins is the same ratio as the x6/8/B 100 pin body, but this part adds 32 Kbytes of SRAM, 8 Kbytes of EEPROM and two operational amplifiers in the same footprint, so an upgrade from the 128 Kbyte code does not touch the pinout review.

The glass driver reaches 4x44 or 8x40 segments, 176 or 320 segments on 48 pins. A controller that shows a measured value, a setpoint, a bar graph and six annunciators uses the 8x40 arrangement, and the bias network for eight backplanes is the part of that decision that has to match the glass.

The LQFP100 in this document is rated 43 C/W junction to ambient, so at an 85 C ambient against a 110 C junction the budget is 581 mW. A backlight or a relay driver sharing the board is the usual consumer of that budget, not the microcontroller.

1.4 microamps in Stop with the RTC is 12.3 mAh over a year, and 0.44 microamps in Stop with the wakeup lines armed is where a controller that wakes on a key press lives. The 32 Kbytes of SRAM stay powered in that mode, so a measurement in progress survives the sleep.

25 analog channels on a 1 Msps 12 bit converter is the ceiling for this document. At 3.3 V one LSB is 0.806 millivolts, so a 10 millivolt signal is twelve counts and the two operational amplifiers in front of the converter are what make small signals worth sampling.

The 8 Kbytes of EEPROM hold calibration and totals across a firmware update because they are a separate array from program flash. The double bank flash in the xD document is where read while write appears; on this part the flash is a single bank and a write stalls the core unless the routine runs from RAM.

The step up in this document is the xD part with 384 Kbytes, which is a different document and adds the memory interface for external static memory. The step down is RBT6 at 128 Kbytes, which keeps the 100 pin footprint but gives up 16 Kbytes of SRAM and 4 Kbytes of EEPROM.

Where this order code fits

It is the widest member of the 256 Kbyte line with the glass driver, so it goes on analysers, dosing controllers and utility meters that need a full annunciator display and 25 analog inputs. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What does the part offer over the 128 Kbyte code in the same body? Double the flash and SRAM, double the EEPROM, two operational amplifiers, 25 analog channels and the step-up converter for the display. The pin count and the footprint do not change.

Is the display driver the same as the smaller body? The 100 pin body drives 4x44 or 8x40 segments, against 4x18 in the 48 pin body. The larger glass needs the larger package because the segment lines are bonded out only there.

How long can it hold data with the main rail off? The VBAT domain keeps the RTC and the backup registers alive from a separate cell. The data EEPROM is non volatile and does not need that rail, so calibration survives a full power removal.

What is the 384 Kbyte equivalent? STM32L152VDT6 in the STM32L151xD document, same 100 pin body, 48 Kbytes of SRAM, 12 Kbytes of EEPROM and an interface for external static memory.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.