Contact Us

STM32L151CCU6

Brand: ST
ST STM32L151CCU6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32L151CCU6 — MCU & Embedded Processors | Superb Automation

STM32L151CCU6

ST — MCU & Embedded Processors

Product Overview

The STM32L151CCU6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32L151CCU6: 256 Kbyte, UFQFPN48 body

STM32L151CCU6 is a member of the STM32L151xC and STM32L152xC low power line described by DocID022799 Rev 13. The order code fixes 256 Kbytes of Flash, 32 Kbytes of SRAM, the UFQFPN48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 14 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down supply.

Order code and memory

Order codeSTM32L151CCU6
Program Flash256 Kbytes
SRAM32 Kbytes
Data EEPROM8 Kbytes with ECC
PackageUFQFPN48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels14 channels on the 12 bit converter
Digital to analog converter2 channels of 12 bits
Segment LCD drivernot present on this part
Supply voltage1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down
Maximum CPU clock32 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient
DatasheetDocID022799 Rev 13

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit
Clock sources1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC trimmed to plus or minus 1 percent, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC, and a PLL that also produces the 48 MHz USB clock
Low power modes185 microamps per MHz in Run mode, 8.6 microamps in Low power run, 1.4 microamps in Stop with the RTC, 1.15 microamps in Standby with the RTC and 0.44 microamps in Stop with 16 wakeup lines armed
Timerseleven timers: one 32 bit timer, six 16 bit timers with up to four compare channels, two 16 bit basic timers and two watchdog timers
Serial interfacesup to eight SPI blocks of which two are I2S, two I2C blocks with SMBus and PMBus, three USARTs and one USB 2.0 device port; five of the eight SPI blocks are USARTs used in synchronous mode
Analogone 12 bit ADC at 1 Msps, two 12 bit DAC channels, two operational amplifiers and two ultra low power comparators, with capacitance sensing on up to 23 channels
Memory interfacenot present on this body
Flash and EEPROM enduranceprogram memory rated 10 kcycles at 105 C, EEPROM cycling stated separately in the same table, and retention given as 30 years at 85 C against 10 years at 105 C
Thermal resistance junction to ambient33 C/W on UFQFPN48
Input tolerance70 of the 83 I/O on the 100 pin body are 5 V tolerant, all mappable on 16 external interrupt vectors
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC and the backup registers alive with the main rail off
Statusfull production per the datasheet cover

Points to check before this part goes on a BOM

The order code is C for 48 pins, C for 256 Kbytes of Flash, U for the UFQFPN body and 6 for the industrial range. The flash letter moved from B to C between the x6/8/B document and this one, and with it the SRAM doubled from 16 to 32 Kbytes and the EEPROM from 4 to 8 Kbytes.

The UFQFPN48 in this document is rated 33 C/W junction to ambient, so with a 110 C junction limit and an 85 C ambient the part can shed 758 mW. That is a better figure than the LQFP48 of the same pin count because of the exposed pad, provided the pad is actually soldered down to copper.

The 8 Kbytes of EEPROM are double what the x6/8/B codes carry, which matters for anything that logs: at four bytes per record there are 2048 records per full cycle, and the endurance table gives the same 30 kcycles minimum, so about 61 million record writes before the array is outside its rating.

This is a 151 part, so there is no segment driver. The 152 codes in the same document carry 4x18 segments in this body, and the step-up converter for the glass is part of that driver, which is why display boards in the 48 pin body come from the other prefix.

Two operational amplifiers appear on this line and not on the x6/8/B codes. They sit in front of the 12 bit converter and can buffer a sensor bridge without an external part, which is often the reason a board moves up from the smaller document rather than adding an op amp to the BOM.

The 185 microamps per MHz in Run mode is a lower figure than the 214 of the previous generation, and 0.44 microamps in Stop with 16 wakeup lines armed is the mode a battery logger spends its life in. The 1.4 microamps figure in the same table is Stop with the RTC, which is the number for a part that keeps time between readings.

37 general purpose I/O out of 48 pins is the same allocation as the smaller document, so a board that outgrew 128 Kbytes can keep its pin functions and change only the memory. That is the practical upgrade path in this body, and it does not require a new pinout review.

The 14 analog channels share pins with the USB pair, the crystal and the debug port. On a part with 32 Kbytes of SRAM the temptation is to sample more channels, and the honest count of free analog pins after USB and debug is closer to nine on a full application board.

Where this order code fits

It is the 256 Kbyte part in the 48 pin quad flat no lead body, used where the firmware needs a file system or a protocol stack but the board cannot take a 64 pin package. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How much memory does this part carry? 256 Kbytes of Flash, 32 Kbytes of SRAM and 8 Kbytes of EEPROM, all with ECC on the flash and EEPROM arrays. It is the largest memory available in the 48 pin body of this line.

Does it have the segment display driver? No. The prefix 151 marks the part without the LCD driver. STM32L152CCU6 in the same document is the equivalent with 4x18 segments.

What is the thermal headroom in this package? 33 C/W junction to ambient, which is 758 mW at an 85 C ambient with a 110 C junction. The figure depends on the exposed pad being soldered to a copper area on the board.

Can the existing 48 pin board take it directly? Only if the board already uses the UFQFPN48 footprint. The LQFP48 codes in the smaller document are not footprint compatible, so moving up in memory also means moving the land pattern.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.