STM32L100R8T6
Product Specifications
STM32L100R8T6
ST — MCU & Embedded Processors
Product Overview
The STM32L100R8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32L100R8T6: 64 Kbyte, LQFP64 body
STM32L100R8T6 is a member of the STM32L100C6 and STM32L100R8/RB access line described by DocID024295 Rev 6. The order code fixes 64 Kbytes of Flash, 8 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 20 analog channels, and the core runs at up to 32 MHz from a 1.8 to 3.6 V supply.
Order code and memory
| Order code | STM32L100R8T6 |
| Program Flash | 64 Kbytes |
| SRAM | 8 Kbytes |
| Data EEPROM | 2 Kbytes with ECC |
| Package | LQFP64, 10 x 10 mm, 64 pins |
| Maximum general purpose I/O | 51 |
| Analog input channels | 20 channels on the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| Segment LCD driver | 4x32 or 8x28 segments |
| Supply voltage | 1.8 to 3.6 V |
| Maximum CPU clock | 32 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient |
| Datasheet | DocID024295 Rev 6 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit |
| Clock sources | 1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz internal RC, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC and a PLL for the 48 MHz USB clock |
| Low power modes | 214 microamps per MHz in Run mode, 9 microamps in Low power run, 1.2 microamps in Stop with the RTC, 0.9 microamps in Standby with the RTC and 10 nanoamps of I/O leakage |
| Timers | ten timers: six 16 bit general purpose timers with up to four compare channels, two 16 bit basic timers and the independent and window watchdogs |
| Serial interfaces | two SPI blocks at 16 Mbit/s, two I2C blocks with SMBus and PMBus, three USARTs with ISO 7816 and IrDA support and one USB 2.0 device port |
| Analog | one 12 bit ADC at 1 Msps, two 12 bit DAC channels and two ultra low power comparators |
| Memory interface | not present on this body |
| Flash and EEPROM endurance | flash rated 10 kcycles with retention stated after 100 kcycles at 85 C in the same table |
| Thermal resistance junction to ambient | 45 C/W on LQFP64 |
| Input tolerance | 42 of the 51 I/O on the 64 pin body are 5 V tolerant, all mappable on 16 external interrupt vectors |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC and the backup registers alive with the main rail off |
| Status | full production per the datasheet cover |
Points to check before this part goes on a BOM
The order code is R for 64 pins, 8 for 64 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. The 100 prefix is the access line: the peripheral set is fixed at two SPI, two I2C, three USART and one USB, and there is no multispeed RC or crystal-less USB option.
2 Kbytes of EEPROM against 4 in the 151 line is the visible cost of the access line, and 8 Kbytes of SRAM against 16 is the invisible one. A firmware image that keeps a display map and a calibration table fits in 8 Kbytes, and one that keeps a protocol stack with buffers usually does not.
The display driver covers 4x32 or 8x28 segments on the 64 pin body, so 128 or 224 segments from 36 pins. That is the same driver capability as the STM32L162 branch, which is what makes the access line usable for a metering product where the glass is already specified.
The LQFP64 is rated 45 C/W junction to ambient, so 444 mW at an 85 C ambient against a 105 C junction. The part draws 6.85 mA at the full 32 MHz from a 1.8 V rail, which is about 12 mW, so the budget belongs to the display, the relays and the regulator.
1.2 microamps in Stop with the RTC is 10.5 mAh over a year and 0.9 microamps in Standby is 7.9 mAh, with 10 nanoamps of I/O leakage on top. On a thermostat that sleeps between readings the cell life is set by those two numbers plus the display, and the display is usually the larger of the three.
20 analog channels on a 1 Msps 12 bit converter is generous for an access line part, and it is the reason this code appears on multi sensor boards. The channels share port C with the display lines, so a full 4x32 glass leaves fewer than twenty channels available in practice.
There is no EEPROM ECC difference to worry about at this density, but there is a real limit: 2 Kbytes at four bytes per record is 512 records per full cycle, and the endurance table states retention after 100 kcycles at 85 C, which is a different qualification from the 30 kcycle figure in the other line.
The pin compatible code above is RBT6 with 128 Kbytes and 10 Kbytes of SRAM. It is the only step up in this document, and it keeps every pin function, so a product that outgrows 64 Kbytes does not need a new board revision, only a new part number.
Where this order code fits
It is the 64 Kbyte member of the access line with a glass driver, so it fits thermostats, timers and simple meters that need a display and a fixed feature set at the lowest part cost. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
What is left out compared with the STM32L151 line? Half the EEPROM and half the SRAM at the same flash density, no multispeed internal RC, no capacitive sensing and a smaller set of serial ports. The display driver, the USB port and the converter are present.
How many segments can it drive? 128 segments in the 4x32 arrangement or 224 in the 8x28 arrangement, using 36 pins on the 64 pin body. The 48 pin body of the same line drives 4x18.
Is 8 Kbytes of SRAM enough? For a thermostat or a timer with a display map, a calibration table and a serial port, yes. A product that buffers records or runs a file system needs the 128 Kbyte code with 10 Kbytes, or a part from the 151 line.
What is the retention figure for the EEPROM? The endurance table states retention after 100 kcycles at 85 C, which is a different qualification from the 30 kcycle figure quoted in the STM32L151 documents. Re qualification has to read the table rather than assume one figure for the family.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.