Contact Us

STM32L071RZT6

Brand: ST
ST STM32L071RZT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32L071RZT6 — MCU & Embedded Processors | Superb Automation

STM32L071RZT6

ST — MCU & Embedded Processors

Product Overview

The STM32L071RZT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32L071RZT6: 192 Kbyte, LQFP64 body

STM32L071RZT6 is a member of the STM32L071xx access line low power family described by DS10690 Rev 7. The order code fixes 192 Kbytes of Flash, 20 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled and 1.8 to 3.6 V without it supply.

Order code and memory

Order codeSTM32L071RZT6
Program Flash192 Kbytes
SRAM20 Kbytes
Data EEPROM6 Kbytes with ECC
PackageLQFP64, 10 x 10 mm, 64 pins
Maximum general purpose I/O51
Analog input channels16 channels on the 12 bit converter
Digital to analog converternot present
Segment LCD drivernot present on this part
Supply voltage1.65 to 3.6 V with the brownout reset enabled and 1.8 to 3.6 V without it
Maximum CPU clock32 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient
DatasheetDS10690 Rev 7

Peripheral and electrical parameters

CoreARM Cortex-M0+ at up to 32 MHz, 0.95 DMIPS per MHz, memory protection unit
Clock sources1 to 25 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC and a PLL for the core clock
Low power modes93 microamps per MHz in Run mode, 0.86 microamps in Stop with the RTC and 20 Kbytes of RAM retained, 0.29 microamps in Standby on three wakeup pins and 41 microamps for a 12 bit conversion at 10 ksps
Timerseleven timers: two 16 bit timers with four channels, two 16 bit timers with two channels, one low power 16 bit timer, two 16 bit basic timers, the RTC, SysTick and the two watchdogs
Serial interfacesup to six SPI blocks of which one is I2S, three I2C blocks of which two carry SMBus and PMBus, four USARTs of which two carry ISO 7816 and IrDA, one UART and one LPUART that wakes from Stop
Analogone 12 bit ADC at 1.14 Msps and two ultra low power comparators; this line carries no DAC
Memory interfacenot present on this body
Flash and EEPROM enduranceflash and EEPROM cycling are listed separately, with retention stated at 85 C and at 105 C after 10 kcycles
Thermal resistance junction to ambient46 C/W on LQFP64
Input tolerance5 V tolerant on up to 51 I/O of the 64 pin body, all mappable on 16 external interrupt vectors
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC and the backup registers alive with the main rail off
Statusfull production per the datasheet cover

Points to check before this part goes on a BOM

The order code is R for 64 pins, Z for 192 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. It is the top density of the document, and the SRAM and EEPROM stay at 20 and 6 Kbytes, so the step up buys program space only.

The 64 Kbyte difference over the 128 Kbyte code is the space a radio stack or a mesh protocol takes, and a firmware image that has to hold both a stack and an application image for a boot swap needs the top density. Nothing else in the part changes with the flash letter.

192 Kbytes is organised with the same ECC and the same page size as the smaller densities, so an application written for the 128 Kbyte code moves without a memory map change other than the size of the region it uses for storage. The EEPROM address stays at the same offset.

The low power figures carry over unchanged: 0.86 microamps in Stop with the RTC and 20 Kbytes retained, 0.29 microamps in Standby on three wakeup pins, and 93 microamps per MHz in Run mode. The larger flash costs nothing in the sleep states that decide the product life.

The LQFP64 is rated 46 C/W junction to ambient, which is 435 mW at an 85 C ambient against a 105 C junction. On a node in a sealed enclosure the ambient is the problem, and the part has to be derated for the temperature rise inside the box rather than the room.

16 analog channels on the 1.14 Msps 12 bit converter and no DAC on this line. A node that needs an analog output for a 4 to 20 mA loop has to use a PWM channel and a filter, or move to a part with a converter, and that is a bill of materials decision rather than a firmware one.

The LPUART, the two ISO 7816 USARTs and the three I2C blocks are the interfaces a metering node uses, and the 192 Kbyte code keeps all of them. A code from the 072 branch would add USB at the cost of moving to a different document and a different set of errata sheets.

There is no pin compatible part above this density in the document. A product that outgrows 192 Kbytes has to leave the L0 family for the L1 or L4 lines, and that is a different pinout, a different core and a different current budget in every case.

Where this order code fits

It is the 192 Kbyte member of the same family, chosen where the firmware carries a radio stack or a protocol suite and the node still has to sleep at under a microamp. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What does the Z suffix mean? 192 Kbytes of Flash. The R prefix fixes 64 pins, T the LQFP body and 6 the industrial range, so Z is the only field that differs from the 128 Kbyte code in the same body.

Does it have more RAM than the 128 Kbyte code? No. Both carry 20 Kbytes of SRAM and 6 Kbytes of EEPROM. The step up in the flash letter buys program space and nothing else.

Can it drive a 4 to 20 mA loop? Not directly. There is no DAC on this line, so a loop driver needs a PWM channel with a filter and an external amplifier, or a part from a line that carries a converter.

Is it the largest density in the family? In this document yes, at 192 Kbytes. Above that the choice moves to another family with a different core, so the pinout and the current budget are both new.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.