STM32L052R8T6
Product Specifications
STM32L052R8T6
ST — MCU & Embedded Processors
Product Overview
The STM32L052R8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32L052R8T6: 64 Kbyte, LQFP64 body
STM32L052R8T6 is a member of the STM32L052x6/x8 low power line described by DS10182 Rev 10. The order code fixes 64 Kbytes of Flash, 8 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V supply.
Order code and memory
| Order code | STM32L052R8T6 |
| Program Flash | 64 Kbytes |
| SRAM | 8 Kbytes |
| Data EEPROM | 2 Kbytes with ECC |
| Package | LQFP64, 10 x 10 mm, 64 pins |
| Maximum general purpose I/O | 51 |
| Analog input channels | 16 channels on the 12 bit converter |
| Digital to analog converter | 1 channel of 12 bits |
| Segment LCD driver | not present on this part |
| Supply voltage | 1.65 to 3.6 V |
| Maximum CPU clock | 32 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient |
| Datasheet | DS10182 Rev 10 |
Peripheral and electrical parameters
| Core | ARM Cortex-M0+ at up to 32 MHz, 0.95 DMIPS per MHz, memory protection unit |
| Clock sources | 1 to 25 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC and a PLL for the core clock |
| Low power modes | 88 microamps per MHz in Run mode, 0.8 microamps in Stop with the RTC and 8 Kbytes of RAM retained, and 5 microseconds wakeup from flash |
| Timers | nine timers: one 16 bit with four channels, two 16 bit with two channels, one 16 bit low power timer, one 16 bit basic timer for the DAC, the RTC, SysTick and the two watchdogs |
| Serial interfaces | up to four SPI blocks of which one is I2S, two I2C blocks with SMBus and PMBus, two USARTs with ISO 7816 and IrDA, one UART, one LPUART and one USB 2.0 port that runs without a crystal |
| Analog | one 12 bit ADC at 1.14 Msps, one 12 bit DAC channel and two ultra low power comparators |
| Memory interface | not present on this body |
| Flash and EEPROM endurance | flash and EEPROM cycling are listed separately, with 30 years of retention at 85 C after 10 kcycles and 10 years at 105 C |
| Thermal resistance junction to ambient | 45 C/W on LQFP64 |
| Input tolerance | 45 of the 51 I/O on the 64 pin body are 5 V tolerant |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC and the backup registers alive with the main rail off |
| Status | full production per the datasheet cover |
Points to check before this part goes on a BOM
The order code is R for 64 pins, 8 for 64 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. Memory and core match the 48 pin code exactly, so the difference between the two is 14 more I/O and 6 more analog channels.
51 general purpose I/O with 45 of them 5 V tolerant is a useful ratio for an interface board that has to accept 5 V sensors. The 5 V tolerance is a pin property and not a level shifter, so a 5 V sensor can connect directly where the pin is tolerant and needs a divider where it is not.
16 analog channels against 10 on the 48 pin body is the reason this code appears on sensor concentrators. The channels share the ports with the USB pair and the crystal, and on a board that enumerates over USB two of the sixteen are already spoken for.
0.8 microamps in Stop with the RTC and 5 microseconds wakeup are unchanged from the smaller body, so a battery powered board does not pay for the extra pins. The LQFP64 is rated 45 C/W junction to ambient against 55 for the LQFP48, which is 444 mW against 364.
The USB port enumerates without a crystal, which on a 64 pin board with sixteen analog inputs is worth more than on a dongle: it frees two pins that would otherwise carry a crystal and removes a component that has to be placed close to the part.
The single 12 bit DAC channel and the two comparators share pins with the analog inputs, so the effective channel count on a board that uses the DAC drops by one or two. That arithmetic belongs in the pin budget and not in the datasheet summary.
2 Kbytes of EEPROM and 8 Kbytes of SRAM are the same as the 48 pin code. A product that stores a calibration table and a device identity is fine, and a product that logs readings needs an external memory part or a larger code from another family.
The 48 pin code C8T6 is the footprint alternative and the 053R8T6 adds the display driver at the same 64 pins. A board that needs neither the extra pins nor the display stays on the 48 pin part and saves board area.
Where this order code fits
It is the same 64 Kbyte part in the 64 pin body, used where sixteen analog channels and a wider set of serial ports are needed alongside the crystal-less USB port. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the BOM Shortage Recovery page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
How many 5 V tolerant pins does it have? 45 of the 51 I/O on this body. Tolerance is a pin property, so a 5 V sensor connects directly only on those pins and needs a divider elsewhere.
Does the extra package size change the current consumption? No. The die and the core are the same, so Run, Stop and Standby currents match the 48 pin code. Only the thermal resistance and the pin count change.
Is there a version with a display driver? STM32L053R8T6 in a separate document, same 64 pin body and same memory, adds 4x32 or 8x28 segment drive alongside the crystal-less USB port.
What is the largest memory in this family? 64 Kbytes of flash and 8 Kbytes of SRAM for the 052 line. The 071 line in another document goes to 192 Kbytes of flash with 20 Kbytes of SRAM and a different peripheral set.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.