STM32F207VGT6
Product Specifications
STM32F207VGT6
ST — MCU & Embedded Processors
Product Overview
The STM32F207VGT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F207VGT6: 1024 Kbyte, LQFP100 body
STM32F207VGT6 is a member of the STM32F205 and STM32F207 performance line described by DS6329 Rev 18. The order code fixes 1024 Kbytes of Flash, 128 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 82 general purpose I/O and 16 external channels on each of the 12 bit converters, and the core runs at up to 120 MHz from a 1.8 to 3.6 V supply.
Order code and memory
| Order code | STM32F207VGT6 |
| Program Flash | 1024 Kbytes |
| SRAM | 128 Kbytes |
| Package | LQFP100, 14 x 14 mm, 100 pins |
| Maximum general purpose I/O | 82 |
| Analog input channels | 16 external channels per converter |
| Digital to analog converter | not present |
| External memory controller | bank 1 or bank 2 only on this 100 pin body, bank 1 multiplexed NOR or PSRAM on NE1, bank 2 a 16 or 8 bit NAND on NCE2, no interrupt line because port G is not bonded |
| Supply voltage | 1.8 to 3.6 V |
| Maximum CPU clock | 120 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DS6329 Rev 18 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 120 MHz with the adaptive real time accelerator, 1.25 DMIPS per MHz, 150 DMIPS, a memory protection unit and single cycle multiply and divide |
| Clock sources | 4 to 26 MHz high speed external crystal, 16 MHz factory trimmed internal RC, 32.768 kHz low speed internal and external sources, a main PLL and a separate audio PLL for the I2S blocks |
| Timers | two advanced-control 16 bit timers with complementary outputs and dead time, four full featured general purpose timers of which TIM2 and TIM5 are 32 bit, six further general purpose 16 bit timers, two basic timers, the independent and window watchdogs, the SysTick counter and the RTC, which is the seventeen the cover counts |
| Serial interfaces | three SPI blocks two of which mux to I2S, three I2C blocks, four USARTs and two UARTs, two CAN 2.0B active controllers and one SDIO interface |
| DMA | two DMA controllers with eight streams each and a FIFO per stream, sixteen streams in total, with circular buffer support |
| ADC | three 12 bit successive approximation converters with a 0.5 microsecond conversion time, each sharing up to 16 external channels, up to 24 channels across the three on the larger bodies and up to 6 Msps in triple interleaved mode |
| DAC | two 12 bit channels with output buffers |
| Ethernet | 10/100 MAC with dedicated DMA, MII or RMII, IEEE 1588 timestamping |
| Camera interface | parallel camera interface present in the line, but the usable data width on this body follows the pin table and is limited to the low byte |
| Cryptographic acceleration | not present on this part |
| Programmable voltage detector | programmable voltage detector with selectable thresholds, plus power on reset, power down reset and brownout reset |
| Debug port | serial wire debug and JTAG, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC, the 4 Kbytes of backup SRAM and the backup registers alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C and 1 kcycle at 105 C, with 30 years of retention at 85 C after one kcycle, 20 years at 55 C after 10 kcycles and 10 years at 105 C |
| Thermal resistance junction to ambient | 46 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant, with fast I/O toggling to 60 MHz on the larger bodies |
| USB | one OTG full speed port on the device pins and one OTG high speed port that needs an external ULPI PHY |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
One megabyte of Flash in a 100 pin package is the reason this code exists. A board that runs the whole application from internal memory, with a TCP stack, a file system for logs and a bootloader, needs the top density, and the 100 pin body keeps the board small. The SRAM is the full 112 plus 16 Kbytes, so the memory profile matches the 144 pin 1 Mbyte part exactly.
Ethernet on 100 pins is practical with RMII and tight with MII. RMII needs the 50 MHz reference clock, which can come from the PHY or from the microcontroller's MCO output, and about nine signal pins on port A and port C. MII needs sixteen, which on this body forces the memory controller down to NAND only, so most boards in this package choose RMII.
The camera interface is on the silicon but this body cannot carry a wide parallel bus for it. Boards that need 10, 12 or 14 bit camera data take the 144 pin part; on 100 pins the interface is limited to the pins that are actually bonded, which is the low byte. The distinction matters because the datasheet feature list is written for the family, not for the package.
The memory controller is reduced here exactly as on the STM32F205 100 pin part: bank 1 multiplexed NOR or PSRAM on NE1, or bank 2 as a 16 or 8 bit NAND on NCE2, with no interrupt line because port G does not exist on this package. A board that needs a non multiplexed bus, four chip selects or a NAND ready line moves up to the 144 pin body.
The 46 C/W of the LQFP100 gives about 430 mW at 85 C ambient. Running 1 Mbyte of code at 120 MHz with the MAC active and RMII reference clock on is the heaviest configuration on this line in this package, and the 100 pin body has fewer pins to spread the I/O current over than the 144 pin one, so the pin current and the core current both belong in the same budget.
Where this order code fits
It is 1 Mbyte of Flash with Ethernet in the 100 pin body, the configuration used by networked controllers that have to fit a 14 x 14 mm package and still run a full application from internal memory. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Does this part have Ethernet and 1 Mbyte of Flash at the same time? Yes. The G density is 1 Mbyte of Flash and the F207 line carries the 10/100 MAC. It is the smallest package in which the two come together.
Can a camera sensor be connected on this package? Only with the pins the 100 pin body bonds for the interface, which limits the data width to the low byte. A 10, 12 or 14 bit sensor needs the 144 pin or 176 pin body.
Which package is smaller, this one or STM32F207IGH6? This one in board area at 14 x 14 mm against 10 x 10 mm for the UFBGA176, so the ball grid is physically smaller. The LQFP100 is easier to inspect and rework, which is why it is the more common choice outside high volume assembly.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.